6.4.1.2 Packet Tracer - Skills Integration Challenge

hi friends welcome to war in this video we are going to see the packet race our activity skills integration challenge here we can see our addressing table also here we can see our Avilan table coming to the scenario in this activity you will demonstrate and to reinforce your ability to configure routers for interval and communication and to configure static roads to each destinations outside of your network among the skills you will demonstrate are configuring inter VLAN routing static and default routes here we can see our requirements we will let you when bavin configure inter VLAN routing on r1 based on the addressing table yes here we can see all addressing table also we can see the router r1 here in our topology coming to our addressing table here we can see the device are run and its interfaces that is serial 0/0 spanner 0 also here we can see the sub interfaces a Gigabit Ethernet 0 sonars 0.10.0 30.8 e 899 and its IP address subnet mask also we can see the VLAN number here we will let check in r1 we will check the interface details your show running config and we will verify the interface here we can see the interface a serial 0 / 0 / 0 is already configured also here we can see the interface a Gigabit Ethernet a 0/0 is not configured so here we have to configure the sub interfaces also here we can see it's shut down first of all we will configure or the sub interface a Gigabit Ethernet 0 smart 0.10 here we can see the IP address a submit to mask also VLAN number coming to r1 configure terminal we have to go to that sub interface interface a Gigabit Ethernet co-star 0.10 so we have to give a encapsulation dot1q then the VLAN ID as specified in our crossing table that is 10 also we are going to set the IP a truss here is that reserved for this interface 1 7 2.30 1.10.10 to 5 5 to 5 5.0 now we will configure the next just have interface a Gigabit Ethernet does euros now 0.20 you will exit and we will go to that sub interface 0.20 no we have to give encapsulation dot1q 20 also we have to set the IP address so it's quite easy here we have to change 170 2.31 dot that 20.1 as per our addressing table also we will go to the next 2 sub interface that is 0.30 and in encapsulation dot1q 30 also we have to set the IP address it's 1 7 2 door that you 1.30 dot 2 1 now we will go to the sub-interface 0.88 eurisk at 0.88 so we know how we are accessing these commands I mean the previously entered commands so we have to use the shortcut I mean be able to use the key up or down arrow from our keyboard so that we get all the commands what already used previously well hurry how to give a hint capsulation door to one q88 also here to set the IP address here or is that so 88.1 right next to sub interface is gigabit a torrent 0 slash 0 to 99 here we can see the VLAN is 99 and this is the native VLAN so we have to set accordingly in this r1 right we have to go to the interface so gigabit authority rose or 0.99 here we are going to give a encapsulation dot1q 99 also we have to make this as native VLAN so we have to give the command in a to you also we have to set the IP at Russ so 1 7 2 Road 31 dota 99.1 coming to the policy here we can see the interface that we got the third 0/0 in this router r1 is it down we have to activate this interface so once we activate this interface all the sub interface also will be activated so we will go to that interface interface we go with the third 0/0 and here we are going to queue the command in ohshit on so that all the sub interface also will be activated here we can see those messages you can see the sub interfaces here door 20 or 30 . 88 also 99 coming to the next two requirements the configure chunking or es 1 coming to your topology here we can see our s 1 which is connecting to our router r1 we are going to configure at ranking in this interface a gigabit Authority 0/1 enable configured terminology how to go to that particular interface it is Gigabit Ethernet 0 / 1 which is connecting to our router r1 here we are going to give a support mode answer trunk also we are going to set trunk native VLAN 99 copy running-config - static config we will verify the trunking in s1 show interface trunk here we can see the details porta gigabit authority rose slasher 1 a modern encapsulation status is trunking also we can see native VLAN 99 also we will verify in our router r1 whatever sub interfaces we configured show IP interface brief here we can see the details whole the sub interface and our IP address also we can check the show running config here we can see with with submit to mask now we will go to the next door requirement configure for or directly at naturally static route on heq to each VLANs 10 20 30 and 8800 Regency the router HQ or so here we can see different VLANs seville anton VLAN 20 VLAN 30 and reveal an 88 here we are going to configure these networks as a directly attached to the static route in this router or hgq now we will come to the configuration enabler configure terminal here we have to give IP route then we have to specify the destination prefix Network our trust 1 7 2.31 toward 10.0 for this of interface we got with the torrent 0 star 0.10 now we have to give this a prefix mask 255.255.255.0 also we have to give you the exit interface or a serial 0 / 0 0 also we have to give a tour Network atras we have to change only here 1 7 2.31 dot at 20.0 also we have a 30.0 and finally 80 8.0 coming to the next door requirement configure directly identity static routes on heq to reach outside host configure the primary path through the serial 0 / 1 star 0 interface configure the backup route through the serial 0 / 1 / 1 interface with a 10 ad that is administrative distance coming to the topology here we can see from this heq to this outside host we can traverse through these 2 connection either serial 0/1 zero interface or in serial 0 / 1 / 1 interface so here early dimension the configure the primary path through the serial 0 / 1 / 0 interface that is the upper interface in this a topology and the backup routed through the serial 0 / 1 / 1 interface right here we can see outside host Network a trust to node 9.16 5.20 0.0 also we can see the prefix length as last 27 and that is 255.255.255.0 coming back to HQ configuration here we are going to give IP route then the network address here is that calls for the prefix mask 255.255.255.0 for all so we have to give the exit interface so as mentioned primary it is a serial 0 / 1 / 0 next we are going to configure the backup route through serial 0 / 1 / 1 interface if the administrative distance 10 here we can see that interface so here we are going to use the previous command except one change that is CDL 0 / 1 / 1 also here we are going to set the administrative distance as specified that is 10 now we will go to the next requirement so that is configure it directly attach the default or route on R 1 so here we are not going to configure all these natural routes for this or remote network so here we are going to configure a directly attach a default or route with the exit interface or serial 0 / 0 / 0 coming to the configuration on R 1 enable configure terminal here we are going to give IP route 0.0.0.0 space 0.0.0.0 also we have to give serials Eurostar zeros are zero coming to the last oracular Mensa verify connectivity by making sure all the pieces can ping outside host so you are going to ping from these pieces to this outside host first of all we will try from pca let stop command prompt here is the actress yes we are getting to replay now we will try to try from PCB here is the actress we are getting the replay you will try from PCC link to outside host we are getting the replay and finally we will ping from PC - Dee we are getting the replay well had that solve this by Catrice our activity skills integration challenge firstly we can see the completion status 82 out of 82 friends if you have any doubt in this packet tracer activity please comment below also if you like my video give a thump and if you like to get my future uploading video info intro Gmail you can subscribe this channel thank you

Channel: Tech Acad

Views: 38,426

Keywords:

Id: TsMdHHE5aNQ

Length: 14min 35sec (875 seconds)

Published: Thu Feb 22 2018