Snirt Stopper Bottom Seal Installation

Video Statistics and Information

Video
Captions Word Cloud
Reddit Comments
Captions
hello and welcome to the stopper installation video today I want to show you how easy it is to install a snort stopper on the bottom of your garage door my name is Monte buyer I am the inventor of the snort stopper and you will need these items here for the installation I got a cordless drill a tape measure and a very sharp scissor and the self tapping screws that come with this nerd stopper so this is the bottom tab that will go underneath the door the one may has a smaller bubble the top tab is the one with no bubble and which will have our company logo on that is the one that you will scoot to the door at this part of the installation video I want to show you where we'll open the door to a comfortable working height for myself or yourself as you're installing it so go ahead my assistant hit the door and now at this point we'll stop the door where I recommend for myself okay perfect so now you can see here I'm doing the installation with the door seal and the door at this height so first of all establish my height on the garage door by applying the upper tab and what I'm going to do is slide it all the way over so it just clears the track on the left side I always work from left to right because I'm right-handed so what I'm going to do is establish that and then what I'm gonna do is put my first screw in at six inches from the end so just snug and then when I'll come back and I'll notch out for my bottom tab but at this point what I'm doing is establishing my foam height and then I'm gonna pull this material tight this nut stopper and then my next screw will go at 12 inches in you will end up with screws in between you will end up screws it at every six inches when you're done but at first what I want to do is go every 12 inches and then at this point I'll have my assistant come in and she can help me hold this and pull it tight and what we want to do is work the wrinkles out of the material from being chipped so getting the next screw again we'll go like 12 inches and as you see I pull it down I got my height established and I'm gonna screw it in at 12 inches you can use the tape measure at this point if you need to to figure out your distances but I've never had to adjust a really good educated guess so another 12 inches so from working from left to right pulling the material tight pulling the wrinkles out this will give it a nice finished tight system and will sit nice and tight on your concrete when you're done [Music] now at this point what I'm going to do is determine the length where I'm going to cut off the remainder of this nerd stopper at the recommended distance so I want to cut it so the bottom tab will just clear the tab on the track on the right side so as you can see right here I'm going to cut and notch this right here basically cut this flush and then I'm going to check it and measure if I need to take any more off so this takes a good sharp scissor and I'll get it cut so it actually clears and that what I'm doing is I'm going to test it and make sure that this track is not so as you can see I have a little bit more - I need to cut so I'm gonna take off just a little bit more okay now you can see I'm just clearing that bottom tab by just about a sixteenth of an inch so at this point I'm going to put some more screws in to finish this out okay check in again making sure I'm clearing on the right side now at this point I'm gonna take my scissor and knotch my tabs on both sides so you can see the tab on the door so what I'll do is I'll just cut it flush pass that so the snoot stopper will sit nice and flat and smooth against the door you do not have to knock this tab but I like to knock some alts a sit flush under the door and you look a little cleaner every door will be a little different due to the manufacturing and how many tabs and how you want to adjust it but don't put this one right here you and do not need to screw the final end of this you can leave that run well they call it but my Glasgow is gonna go right here on this dial of a door right there and now I'm gonna do the same on the other side at this point so that's going to be my last of my initial screws of the first round at this point I could put my last screw in here and that's all I need to do for my nurse first initial so at this point I'm gonna close the door and I'm gonna make sure that my door seal is even set so I put the screws in about 1 inch or 1 foot increments go ahead close the door stand it back I'll take a look make sure I have no daylight underneath my door which as you can see this fits perfect like a glove so go ahead and raise it back up they have no gaps but if I do have any gaps at this time that's where I want to make my adjustment since I only have half the screws in go ahead and stop it please so now what I'm gonna go do is put the rest of the screws in the rest of the way and what I like to do is just pull it down just a little bit so I put a little more tab tension in on the bottom here and I'll put one screw in between all the way down so you end up with one screw every six inches when you're done [Music] okay that's my last girl so now what we're gonna do is we're going to close the door and take one more good look at tante that sits on the concrete and make sure my problems are fixed with the door seal perfect perfect fit no gaps no nothing
Info
Channel: Snirt Stopper
Views: 47,435
Rating: 4.5328469 out of 5
Keywords: Snirt, Stopper, Garage, Door, Seal, Best, insulate, Keep, out, Snow, dirt, ultimate, the, bottom
Id: Eznl_xdu8x4
Channel Id: undefined
Length: 8min 10sec (490 seconds)
Published: Sun May 13 2018
Related Videos
Note
Please note that this website is currently a work in progress! Lots of interesting data and statistics to come.