Cómo hacer un generador de ENERGIA GRATIS con un ALTERNADOR DE COCHE⚡💡💡⚡

We are going to modify this car alternator to turn it into a Brushless generator. First we are going to try to disassemble the alternator pulley. But we cannot because the pulley has a special bearing. So we are going to weld a piece of iron between the pulley and the bearing In this way we block the bearing of the pulley Now we can disassemble the pulley. We continue to disassemble the rear cover AND remove all the screws We remove the support of the brushes or carbons. We do not need this part We also remove the diode rectifier because we do not need it In order to remove it we have to cut the diodes Here we have the three coil connections. We remove the screws from the alternator housing We open the housing We remove the copper winding We also remove the shaft We have to cut all the iron parts of the rotor They look like iron fangs We have already cut the iron parts We put the rotor in the bench drill and smooth the iron surface that we have cut We roll insulating tape to make the surface flat to be able to stick the magnets Here we have the neodymium magnets. They have a lot of force We start to glue the magnets on one side, right where the pieces of iron that we have cut were We glue them with Instant Adhesive or Cyanoacrylate We do the same right where we have cut each piece of iron We have already glued a row of magnets Now we glue another magnet next to the magnets that we have placed It is quite complicated because both magnets repel each other. We fix them with electrical tape until the adhesive dries. And so all the magnets. They have to be glued in pairs When the cyanoacrylate dries we can remove the insulating tape All the magnets that we have glued are with the South Pole facing out Now we use another easier method to glue the magnets in pairs We glue another six pairs of magnets AND the We stick with adhesive on the opposite side, right where the pieces of iron that we have cut were. These magnets have to be glued with the North Pole outwards. All the magnets are already glued. They should look like this Now we empty a bottle of Coca Cola We need the plastic container to continue We have to cut two pieces of the plastic bottle We wrap the container with the pieces of plastic And fix the pieces of plastic with insulating tape Now we seal one end with hot silicone We prepare the Epoxy Resin mixture We fill the entire container that we have created with Epoxy Resin ... And let it dry for 24 hours ... Now we can remove the insulating tape and the pieces of plastic We mount the rotor again in the bench drill and leave the surface smooth so that the electric generator does not vibrate Here we have the finished rotor Now we are going to weld three cables in the three connections of the coils and in each weld of the cables we place heat shrink insulation Now we place the rear bearing of the shaft We mount the copper winding on the rear cover of the casing and now we put the rotor shaft in its place We put the front cover in place ... And we put the screws back to join the casing We fix an electrical connection strip with flanges to the rear cover of the electric generator ... ... and connect the three cables Now we fix this pulley on the Y axis We already have a 10,000W Brushless Electric Generator Single-phase motor coupling We are going to manufacture the motor support Now we assemble the motor pulley Now we manufacture the support of the Brushless Electric Generator We are going to use this wood to join the elements of our Electric Generator We screw the motor and the Electric Generator Now we put the transmission belt And finally we make all the electrical connections And we are going to start up our Free Power Generator And it starts perfectly !!! And here we have our Perpetual Power Generator Testing the Perpetual Power Generator We are going to connect several electrical devices As you can see we activated the switch and it does not work We are going to wind the starter cable. When we pull the cable the Generator will produce enough energy to start the engine, and the motor will continue to move the generator In this way the electrical system feeds itself and generates more electricity than it consumes We start it up and it works perfectly As we can see, it is capable of generating 220 volts And we can put different electrical appliances into operation Hit LIKE and SHARE the video !!! With this small equipment we can generate 220 volts and 10,000 watts of power

Channel: The Crazy Channel

Views: 3,441,422

Keywords: the crazy channel, Energía Gratis, Free Energy, Generador Energía, Energía Infinita, alternador, car alternator, brushless, brushless generator, Diy, mecánica, inventos, inventions, Tutorial, Energy Generator, Homemade, diy, hecho en casa, aerogenerador, electricidad gratis, generador eléctrico, free electricity, como generar energia electrica casera, como generar energia con un alternador de auto, generar energia, generar energia electrica casera, alternador para generar electricidad

Id: -ftPmhYAEr8

Length: 21min 32sec (1292 seconds)

Published: Fri Dec 31 2021