One of the most versatile pieces of tech
for 3D printing is Octoprint - it’s a little webserver that runs on a Raspberry Pi and lets you
remote-control a 3D printer from your computer. Or so you thought. Because the thing is, Octoprint
is so much more than just a way to start and check in on prints remotely: It’s turning more and
more into a full-on 3D printer operating system. There are plugins now that do everything from
AI print watching over sending status infos over your favorite messenger to timelapse tools
that let you do this: [Octolapse timelapse] So today I’m going to walk you through the
setup process on a Raspberry Pi, go over the hardware you need and I’m going to share some
of my favorite plugins for Octoprint. Just like I’m going to share this video’s sponsor, Elegoo!
In this video, I’m going to be using the Elegoo Neptune 2, which is finally starting to have
better worldwide availability. But also, Elegoo have just announced the Mars 3 LCD resin print
now with a 4K monochromatic screen, larger build volume, and an included ChiTuBox Pro license. And
with the Mercury X, Elegoo now have a curing and washing station that fit for the large-format
Saturn. Check them out at the links below. So let’s start out with the hardware needed. First
of all, you’re going to need a Raspberry Pi. I’m using a Pi 4 with 2GB of RAM, and while OctoPrint
can run on almost any Raspberry Pi ever made, you should stick to a Pi 3 and up for
the best experience. Alternatively, you can also run OctoPrint on a Windows, Linux or
Mac OS machine that you already have - as long as that’s not going to reboot in the middle of your
prints someday. I’m looking at you, Windows 10. But for a Raspberry Pi, you’re also
going to need a USB power supply, the recommendation is to not use a “charger”, but
instead something that’s actually labelled a USB power supply. Though from a technical standpoint,
there’s not really any difference between what they do, and especially after the 4, the Pis
have also gotten much better power stages on them as well, so they’re not that finicky
about the power supply you’re using anymore. However, in either case it should be one with
ample power, so your 1A charger you got from Apple is not going to work. I’ve had great experiences
with the chargers / supplies from Anker, this basic dual- or triple-output one works perfectly.
Or if you have a strong 5V supply in your printer, you can also hotwire that onto a USB cable. Just
make sure to shut down the Pi through OctoPrint cleanly before you power off your printer.
Speaking of USB cables, you’ll definitely need a decent one of those, the Pi 4 uses USB-C
now, which is great, but many cables you get with gadgets and the likes are still too flimsy
to provide stable power to the Pi. So, again, I really like the cables from Anker, but if you
have for example a spare USB power delivery charge cable from your laptop, that should work, as well.
The Raspberry Pi itself can detect when there are issues with your power supply, and OctoPrint
will in turn show you a warning when it does. Lastly, to complete the set of parts for basic
functionality, you need an SD card, any card works, but getting one that’s at least decently
fast is going to speed up load times a lot. I’ve got a bunch of these Samsung Evo Plus cards
from my cameras that work fine in a Pi as well, but any card that has an “A” rating
for application performance, like A1 or A2, will work just fine as well. I mean, get
something halfway decent and you’re fine, really. So that’s all the hardware that you actually
need to get Octoprint running, all linked in the description below, but really, if you’re setting
up OctoPrint, you probably want a webcam feed, too. Now, there are two basic options -
getting a USB webcam, or getting a Raspberry Pi camera module. Either one works. The Raspberry
Camera is a fantastic value, but you’re going to need to print some sort of mount or enclosure,
on the other hand, USB webcams are all kind of “meh” for image quality, they’re still good enough
to check in on prints, but most importantly, they’re a bit more convenient to use.
The standard camera would still be the “720p” Logitech C270, but even most
off-brand webcams aren’t any worse for image quality and they pretty much all
work with OctoPrint with no fuss. But if you want something that’s proven,
get a Raspberry Pi Camera or the C270. And that’s it for hardware! Well,
you will also need a computer and a card reader for the setup, but we’re
just going to assume you already have those. Now, for the setup, we’re actually not going to
install OctoPrint directly, we’re going to use OctoPi, which is sort of the official Raspberry
Pi image that has everything already laid out, OctoPrint set up in there, and it’s ready to get
going. Now, I’m going to strongly recommend that you use the official OctoPi image. You’re going
to find modified OctoPrint or OctoPi images from people that say “hey, we’ve got everything
set up for you, it’s got all the plugins already installed”, but the thing is, if it’s
just from some random dude on the internet, you don’t know what else is also installed on
those images and how well they’ve been set up. So, you know, you’re basically inviting the person
making that image into your home network. Best case, everything is fine, perhaps they run
a Bitcoin miner on your Pi when it’s idle, but maybe they’ve got a full-on backdoor set up
in that image that allows them to snoop around your devices, or perhaps they intentionally
burn your printer down one day. You never know. I trust Gina Häußge, who makes OctoPrint, and by
extension, also Guy Sheffer, who makes OctoPi, and, again, I would highly recommend sticking
to their official releases. Setting up plugins the normal way isn’t that hard anyway.
So let’s get started with the setup. I’d actually recommend using a pretty new, but
super convenient way of setting up OctoPi, and that is through the Raspberry Pi imager
you can get from raspberrypi.org/software. Install and run the imager. Under “Choose OS”,
select “Other specific purpose OS” and choose OctoPi. This will automatically download
the newest version of OctoPi for the setup. Then pick your SD card under “Choose Storage”, but
make sure that card has no important files on it, because they’ll be gone in a second. Now, for
our special magic trick, press CTRL + SHIFT + X, and this will bring up the imager’s
secret “Advanced options” menu. Here, enable “Enable SSH”, and pick a modestly secure
password for the “pi” user. Choosing anything that isn’t the default “raspberry” password
will automatically help protect your OctoPi install from malicious actors on the network.
Then, one step down, you can configure your WiFi connection, simply enter your WiFi’s name
and password and choose the correct country code to prevent connectivity issues
later on. Once everything is set up, click “Save” and then “Write”.
Once that’s done, eject the SD card, drop it into your Pi and we’re ready to power
everything up. Plug in the USB cable to power up the Pi and watch the “ACT” LED, that’s going
to be lit for a while, but once that turns off, OctoPrint is going to be ready for use at
http://octopi.local. If your browser can’t find your OctoPrint install, check your router’s
network overview page to find the Pi’s IP address or the “Network” page in Windows Explorer.
Since this is the first time this OctoPrint instance is running, it’s going to show you the
first run wizard. There’s actually not much to say here, just follow the steps, set up your
printer’s dimensions and you’re good to go! All that’s left to do is to power up your printer,
and plug it in through USB. Quick sidenote here, some printers have a flaw in their electronics
where they will backpower the Raspberry Pi through the USB port, which can cause all sorts
of problems from OctoPrint crashing to the Pi’s WiFi disappearing. I’ve put the link to the
forum post about that in the description below. And at this point, you’re ready to start printing. But wait, there’s more! Once you’ve gotten
familiar with OctoPrint, surely you’ll be finding a couple of spots where you’d like to tailor the
experience to your personal needs or preferences. And this is where plugins come in! There’s
a plugin for pretty much everything. But before we go through some of the plugins
I’d recommend, here’s one quick tip that’s going to be super useful. If you use a slicer
that supports it, such as PrusaSlicer, you can directly upload your gcode files to an OctoPrint
install straight from your slicer without saving it to your computer and then having to upload it
manually. Go into OctoPrint’s settings, generate an application key, copy that into your slicer
and then tell it where to find your OctoPrint setup - default is the same octopi.local hostname.
And voila! You’ve got a new send gcode button in your slicer that is going to conveniently send
off your prints to OctoPrint and if you want to, even automatically start them once they’re
uploaded. That is a massive convenience feature. Okay, on to plugins. You can install plugins
right inside the OctoPrint interface - go into the settings again, click “Plugin Manager” and then
“Get more”. You can browse plugins right here, but the “Details” button is going to take you out
of your OctoPrint install, so the most convenient way to install a plugin is to come back to
the plugin manager on your OctoPrint page and just install them from there. So the ones
that I find really convenient for daily use are TouchUI, which gives you a basic,
mobile-friendly interface if you want to quickly check in on your prints from your
phone. By default you get the full interface, which works, but you have to zoom around quite a
bit and TouchUI makes that a lot more convenient. Next up, for printing parts - OctoPrint
includes a basic gcode viewer, but it’s only a layer view and we can certainly do better
than that. Pretty Gcode is one of the options for that. It’s a full-on 3D gcode viewer that syncs
up with your print progress. And while the way it displays extrusion lines isn’t volumetrically
accurate, it’s still super helpful to see what the print you’ve loaded up is going to look like.
But what if the print you’ve started isn’t going as intended? Well, especially if you have more
than one part on the plate of your printer, that’s a bit of a messy situation when one
of them, for example, comes loose from the bed. If you now stop the print, you can throw
out all those parts, but if you keep going, the loose extruded material from the failing
part might mess up all the other ones, too. So what the “Exclude Region” plugin allows you to do
is to tell OctoPrint to, just not send any more print instructions for that area where the part
has failed. That’s super useful and it can save you a lot of time and material should you ever
need to use it. So install it before you need it. Next up, of course, one of the coolest features
OctoPrint enables is getting those magic timelapses of your prints. Instead of your camera
just snapping a picture in a fixed interval, the OctoLapse plugin can sync that up with the end of
a layer and even create those cool nozzle orbiting effects. OctoPi is already prepared to run
OctoLapse without the extra step of installing the Python development package, so you can just click
“Install” and you’ll be ready to use OctoLapse. The setup process will still take a second.
One of the useful things that OctoLapse lets you do is to override your webcam’s exposure, white
balance and focus if you have one with autofocus, so if you just want those settings
without full-on installing OctoLapse, the “Camera Settings” plugin lets you do
exactly that for your viewing pleasure. And lastly, what if you want to check in
on your printer when you’re out on the go. Well, first of all, letting a 3D printer run
without supervision and without you being able to intervene physically is always going to be
something that comes with some risks and you should only do if you really trust your machine.
But, say you do and you want to be able to check in on your machine from anywhere, then the
OctoEverywhere plugin is exactly what you need. You can get the full OctoPrint interface wherever
you are and just check in and make sure things are doing well, and if you have to, you can stop the
print or use Exclude Region to stop things from getting worse. OctoEverywhere is a free service,
but the alternative The Spaghetti Detective is something you might want to look into
as well - it’s got a free tier that allows time-limited use and then paid unlimited plans.
But the big feature of The Spaghetti Detective is AI-based print failure detection. I did a whole
video on that and you can check that out up here. So that should get you pretty
much set with OctoPrint. A big shoutout to Gina Häußge for making
OctoPrint as a free and open source project and a shoutout to her Patrons and
supporters for making that possible as well. So if you enjoy OctoPrint, maybe
consider supporting Gina directly, too. And of course, shoutout to my Patrons and YouTube
members as well, who also make it possible for me to make these videos. Next supporter-exclusive
Q&A hangout is coming up this weekend. That’s it for today, thank you all for watching,
keep on making, and I’ll see you in the next one.
