[How To] Clean and Lube Your Remington 870 in 10 Minutes

Video Statistics and Information

Video
Captions Word Cloud
Reddit Comments
Captions
- If you've ever wanted the quick and dirty on cleaning your scatter-gun without the rambling dialogue and the poorly focused camera shots of the other guys, stick around because today we're going to show you how to clean your Remington M870. All nice and pretty-like. What is up guys my name is John with pewpewtactical.com, your definitive source for gun reviews, gear guides and all things that go bang. We probably don't need to tell you how brutally efficient and simple shotguns are. So we won't. Remington's 870 series shotguns are absolute workhorses. And you can definitely run them quite dirty before they really need a good scrubbing. But the good news is, they're about as easy to clean as they are to use. So let's hop on in. Now we've got a complete M-Pro 7 cleaning kit before us today and it includes their gun cleaner, oil, and copper remover. Plus lots of other essentials. Peep the description below for a link to all the products we used to clean our shotgats as shown in this video. First things first, check your chamber and make sure the shotgun is clear and unloaded. Additionally, check your magazine tube and make sure that your follower's visible, indicating that there are no shot shells in the tube. From here, locate the magazine cap on the barrel end of the mag tube, and unscrew it by twisting counterclockwise. You can see that I've got a magazine tube extension on my 870, so yours is going to look probably a little bit different. Keep a tiny bit of pressure on the cap, as once you unthread it entirely, the spring will push it forward and might escape if you aren't paying attention. Pull your entire magazine tube spring and follower out of the magazine tube. You're now free to separate the barrel from the receiver of the shotgun by pulling it forward. Next, remove the forend assembly by turning the shotgun upside-down and pressing in on the two tabs inside of the receiver. There is one tab on either side of the receiver, so if you're having some trouble, try pressing them in one at a time, and moving the forend assembly forward until it comes loose. Once you've released the forend assembly, move it forward and your bolt and bolt carrier will come free as well. With your shotgun on safe, use your punch to remove the two pins located directly above the trigger assembly. You can now remove the entire trigger group from the receiver. Spritz the inside of the receiver with a bit of your gun cleaner. And then set it aside while we work on the rest of the internal components. Spray your bolt and your bolt carrier with cleaner as well and set them aside. Take your barrel assembly and spray your cleaner down both ends. Inspect your forend assembly's rails for carbon buildup. And wipe them down with a microfiber towel after spraying it with some cleaner. Additionally, wipe down your trigger group as well. If you notice a fair amount of gunk, you can spray the trigger components down with a bit of cleaner. And wipe them down with your microfiber rag. If you've got a lot of fouling in your trigger group, you can go ahead and clean it deeper by very carefully holding the hammer, taking the trigger group off the safe, and slowly depressing the trigger. This will allow you to access the space behind the hammer. Once complete, re-cock the hammer. And set the trigger assembly aside. Retrieve your barrel assembly and go ahead and grab your 12-gauge bore brush out of your cleaning kit. Run your bore brush down the barrel several times, from the rear forward. Once you've loosened up all that grime with the bore brush, go ahead and attach a cotton gun cleaning patch to the bore brush itself, and then run it through the barrel to pick up all of the loose debris and residue. That's a dirty boy. Once those patches are coming out of your barrel relatively clean, go ahead and set it aside and grab your receiver. Use your microfiber towel to wipe down the inside of the receiver, paying particular attention to where the forend assembly rails interface with the receiver. Hopefully this area doesn't have too much grime built up, but you can always break out your brush and get to scrubbing if it does. Inspect your magazine tube for residue. If you've got any buildup in there, you'll want to use a dry cleaning patch to tackle it. Don't spray cleaner or lube into the magazine tube, as this will only attract more gunk in the future. Hit your bolt with your microfiber towel, and then go to town on any more stubborn grime with your brush if necessary. Pay particular attention to the inside of the bolt, and the bolt face itself. Inspect your extractor claw, and ensure that it's free of fouling as well. Boop. Repeat the wipe-down process for your bolt carrier. Apply a dab of lubricant to the surface of your hammer, and again on the trigger spring itself. Lubricate the rails of the forend assembly very lightly. And be sure to spread the lubricant out over the entire surface of the rails. Then wipe off any excess. Insert the trigger assembly back into the receiver, aligning the body pin holes once seated. Starting with the forward-most pin, tap them back into the receiver. Insert your bolt carrier into the matching notches on the forend rails, and set the bolt itself on top of the carrier. Slide the entire forearm assembly over the magazine tube, and begin to reinsert the bolt carrier group back into the receiver. Once you feel resistance, apply pressure onto the internal tabs that you pressed to remove the entire forend assembly from the receiver. Once you've got them depressed, slide the entire assembly back into place. Cycle the pump and the bolt to the rear, at about halfway forward again, giving you enough clearance to get your barrel assembly reattached to the magazine tube. Give your barrel one last check before you reinsert it back into the receiver, paying particular attention to the feed lips of the barrel itself. Reinsert your magazine follower and spring assembly back into the tube. Keep in mind, I do have a magazine tube extension on the end of my 870. But if you do not, go ahead and follow the standard reassembly instructions, including replacing the end cap that keeps the spring in place once it's rotated into the mag tube correctly. Whatever your setup looks like, go ahead and screw the end cap back on once you've got the spring reinserted. Once you've got everything reassembled, go ahead and check to make sure that your pump is cycling correctly. You're done. Now this last step isn't entirely necessary if the outside of your gun is not dirty, but mine is, so I'm gonna hit it with a little bit of cleaner and wipe it down with a microfiber rag. (cheerful music) With that last wipe-down we are done. Alright guys that's gonna do it for us today. Thank you so much for watching. If you enjoyed this content, please go ahead and subscribe to the channel, as we've got lots more guides and how-tos on the way. Once again, my name is John at Pew Pew Tactical, and we will see you next time. (slow digital music)
Info
Channel: Pew Pew Tactical
Views: 196,918
Rating: 4.9212508 out of 5
Keywords: how to clean remington 870, how to clean remington 870 express, how to clean remington 870 pump shotgun, remington 870 disassembly, remington 870, remington model 870, gun cleaning, 12 gauge, shotgun cleaning, remington 870 tactical, gun cleaning products, remington 870 express, remington 870 express tactical, remington model 870 express, shotgun cleaning and maintenance, shotgun cleaning kit, remington 870 shotgun, remington model 870 express pump-action shotgun
Id: ZgmxcN6_78Y
Channel Id: undefined
Length: 10min 21sec (621 seconds)
Published: Tue Jan 08 2019
Related Videos
Note
Please note that this website is currently a work in progress! Lots of interesting data and statistics to come.