Step by Step Papa Pump Install

we're to show today how easy it is to install a zero energy popper pump pump kick everything you need to connect to your flight work and start pumping water the only other things you will need for installations PTFE tape of pipe wrench and an air pump with a pressure gauge if he followed your pipe installation instructions what coming into the chamber should be at least 150 mil off the ground the supply pipe will need to be threaded that you can buy steel pipe pre Freddie first applies of PTFE tape to the friend winding in a clockwise motion now I would put at least four to five rounds on possibly more just screw on the stock bail until it goes hand tight that's quite tight in there grab your pipe wrench and you'll need to do them up several turns from here we need to open them up a flat for you to take a couple of times [Music] I just emptied it out several times for anything B&N from here we'll be good to fit the pump sometimes the adapter is attached to the front of the pump already just remove it and apply some PTFE tape again using enough tape to ensure we make the seal again screaming hand tight once your hand side rep you see spanner which comes in your kit and turn him on a couple more times again ensuring that you make the seal before we fit the pump just double check inside the coupling here that the o-ring is securely in place this will complete our seal when we fit the pub which we just screw straight up and you can see now where we had 150 mil rise on the pipe from the bottom of the tank just to make it easy to turn the pump body on you will feeling go tight hand tight just turn him until you can place him upright without too much difficulty and now we have it before feeling the delivery hose take off the tape we need to just check the develop rubbers on a delivery end or in the correct order and the first rubber in against the seat should be this way around we now all relate their positions so like so and again we all take the position and that we're ready to fit the delivery hose in order to fit the delivery house we'll take off the coupling closest to the team now we can easily turn on the wrestlers he put a pump just turn him on to these hand tight and then finishing off of the seats manner from here we want to position the tee so he's facing upwards so we can easily fit the pressure vessel this point is a good idea to support a pump suitable size bit of wood or concrete block is fine you need to easily be able to remove it so you can service a pump efficiently to finish it off tape up the delivery pipe if we undo the coupling slightly you'll go together easier with paper to tighten them on about turning the whole pipe will finish you off final tighten and para grips not too much just to make sure nice and tight and then we do up the rest of the coupling so that we're not turning the pipe so we're going to continue in the delivery hose there's no need for tape here and so they're sealing the join again we're just going to do them up hand tight there's no need to use grips on this now we need to attach the pressure vessel first we'll need to prime it in order to primum we will calculate the height we're pumping our water to which is this place here is 50 meters now it's 50 meters that I would equate to around about 5 bar but for our air pressure we reduce that by half a bar so I'll be priming this tank to four and a half bar for this setup if you have a particularly high delivery head you may need to contact us for more advice just don't screw the cup it's not your pump and make sure you can hit the pressure you need to hit which in this instance is falling off fit the exhaust extension to the exhaust port and it just pushes to feed the Pressure Vessel I'm gonna touch it to the T connector and screw it more on the tool time it doesn't need any tape it'll go straight up and now we're ready to start the pump our fresh investments Prime's the water in the system and all we're gonna do is open him up and you should see him start straightaway what here is a nice even feet no done beating no misfiring just underneath the exhaust extension yeah you have directions fully opening and sharp now we turn it clockwise we'll open up the valve towards the plus sign to fully open - obviously - the closed sign if we now open him up you will hear the feet even and become slower and essentially we're coming slightly more efficient and we're pumping more water we can look this top blue using the ring beep our position once the pump has been pressurized at no point should you ever just take this pressure vessel off without first releasing the pressure and will do this by turning him twice you can already see the air coming out and now we're just going to leave him safely done now we have been working pump and our first life war is being committed to that plank up the hill we're here to go 24 hours a day seven days a week you know anything they need to do sometimes time check that your filters appear then you throwing through enough water and in potentially a couple years time you may need to change the rubber seal inside [Music] you

Channel: Water Powered Technologies

Views: 320,571

Rating: 4.6609416 out of 5

Keywords: Ram Pump, Hydro Ram, Renewable Energy, Water Pump, Green Energy, Water Powered Technologies, Farm Water, Water Solutions, Off-grid Water

Id: mQCyjkubYFU

Length: 9min 52sec (592 seconds)

Published: Fri Sep 15 2017