Solidworks tutorial | How to make Pressure Vessel in Solidworks

Video Statistics and Information

Video
Captions Word Cloud
Reddit Comments
Captions
welcome back to CAD CAM tutorial today we are going to design an assemble a pressure vessel in SolidWorks this is the pressure vessel asme standard 8 so let's see how to make in SolidWorks tang and manhole-cover are different here we will assemble so let us see how to do in SolidWorks you now here we will make the first part of Pressure Vessel tank pressure tank so let's start we will select front plane a sketch first draw a center line draw a vertical and a horizontal center line make sure it is vertical and it is horizontal now let's start choose a line draw a line and just go back this point and it automatically converts a radius part click up to here and again go to this point and it automatically convert and up to this line point okay now we will assign the dimension first we will assign this distance keep thousand mm 40 mm okay make this radius 120 mm and this radius 1200 mm okay but select this construction line and this point make relation coincide that's it okay now one more define the distance from this centerline 595 mm okay now select let us do the offset entity select here 5mm and select it should be outer dimension and select yes now just do one thing mirror this select this all line and mirror about this vertical line see is going to mirror here okay now select line and connect from this bottom line to this line again select from top line to this line and here bottom just close now act it now our geometry is fully defined 5mm and this is 120 mm now select revolve ooh boss base select this line as a axis choose 360 degree okay now here we will assign the first material polished steel so this is the our tank you can see half section view see this is the over tank that's it now let's first define one plane so choose top plane plane and make the length 740 mm slip direction okay now select this plane is sketch normal do one thing draw a horizontal line and make sure it is passing through origin now draw here some circles let us define the dimension 114 mm okay make three circles equal one two and the last one make relation equal now let us define the distance from here to this line 198 mm and the distance between these two lines 600 mm key 400 mm 520 mm and just sick actually this decision we want 170 but delete it delete this distance now define this distance 170 mm here we want to make one pallet okay now choose offset entities we want to make offset for each circle keep offset 3.6 select this circle inside try this circle and try the last circle okay again choose offset entities and here we will define 6.5 mm and select this circle make sure inside okay now this 4 circles created now we will extrude it this all circles and make the length 151 it should go little inside the tank see is going little inside the tank select ok now again choose the same sketch or select this previous sketch select extruded cut and here clear this and select inside line reverse direction select inside line that's it and you can little increase now this is going to cut the hole inside the pipe okay now see it makes the now just hide this plane now you can see it here this is the inlet and outlet ports for pressure vessel now let us move for the next part now choose front plane is sketch normal and choose your corner rectangle and draw a rectangle select this line and draw up to here now define the length and width 250 mm 5 mm and the distance from this line keep 372 mm okay again choose corner rectangle and here also we want to define one more we find the length to 55 mm and the distance from here to this line 372 mm okay now we will select revolver boss/base now we will try to revolve it first do one thing draw a center line now select revolve Oh boss base now see it is 360 degree we want not 360 degree keep 65 degree one direction and select direction to also see 65 degree both direction okay now see a support is created tank support now let's move for the next part again choose front plane a sketch normal choose corner rectangle and here also we want to draw select this top line keep 250mm 5mm and the distance from one end to this end line keep 125 mm okay select one centerline what vertical centerline make sure it is vertical now select this all line just mirror about this line okay now it is mirror here now we will make it revolve you boss/base delete this line choose centerline and draw a horizontal line exists now select this horizontal line and try to revolve a boss/base see it is also going to revolve here 360 degree but we want only eight eight degree both direction okay now this is the base plate for lifting hook here we will make lifting hook let us try to make lifting hook choose front plane a sketch and here we will make some lifting hook so first draw a center line choose a mid line select line connect from one end to this end go up exit draw here two circles only small one big now let us define the dimension 60 daya and this outer one 120 this height keep 45 degree and the bottom length select 100 mm choose line connect this line to this exit now select both the lines and circle and make relation tangent okay choose mirror now mirror these three lines 1 2 & 3 there are about this line okay choose from entity and trim these inside lines select ok now define the center from 90 mm now this geometry is fully defined okay now we want to mirror these two next direction so do one thing just select draw a 1 vertical line okay it's vertical just mirror select this all geometry mirror about this line see is going to mirror here okay now let's try for extruded boss choose here red plane select 8mm merge okay now this is the lifting hook for Pressure Vessel we will you can lift this hook this tank with the help of this hook okay now again choose front plane is sketch and here we want to create some base so select corner rectangle just below this point keep the length 250 by 5 mm and the distance from outer line 388 mm okay okay again choose one corner rectangle and draw this below this point 388 mm this is the distance okay and extrude this actually we are going to make the base for this tank and choose here Direction D D 155 see select Direction D - 555 this is the base plate for base select okay now we will create one plane so choose top plane plane 7:40 3.5 mm okay choose this plane sketch normal and here we will draw a 1 circle for a Inlet first draw a center line now draw a circle here dot let's define the diameter 89 mm choose offset entity draw a one circle select this circle inside keep 5.5 mm okay now define the length from here to this line one sixty nine point five mm okay now select extruded boss keep the length one sixty nine point five reverse direction it should go inside 10mm to the tank okay that's it now hide this plane this is the inlet now again choose the same axis extruded cut and selected here select clear select this inside circle only and we want to cut so make little deeper okay now see a hole is created inside the tank now here we will make some manhole choose right plane a sketch normal and draw a vertical and horizontal line select line and start to draw from here again choose a line exit now let us define this distance for ninety eight point eight keep 10mm this meg little upward defined only three mm that's it 225 keep 23 mm 5 mm the length 60 3.9 and this length 40 7.5 mm okay this one little drag up upward direction that's it and this overall length make sure this length should be now here we will change for this dimension 220 and this one make 308 point let us make five okay your drag this one inside okay select this both the lines collinear relation select these three lines centerline and this two line and make relation goes anti-symmetric okay then define this length keep 34 mm and the distance from here to this line keep 35 mm okay now select the distance from bottom line to this line to 94.9 okay now our geometry is defined let's define this also six okay now select revolver boss/base select this line as a axis see it is going to rotate revolve select okay now see it is revolved now select this phase sketch select this inside circle convert it and choose extruded cut and cut up to inside because we want to make a hole okay now see the hole is created here now we will make the base so first we will do one thing select write plane plane and we want to create a plane reverse direction key 497 mm no we want actually the midpoint for this so cancel it select this plane plane and choose this side so see it comes mid that select both the end faces okay now our plane is created select this plane sketch normal so let us make the base first first draw a center line select line start from up and connect with Bank exit now let us define the length from here to here or cancel it do just mirror this line this both the lines okay now connect this end to this end okay now just make this length delete this variation first now try to change delete this symmetric relation again we need to draw relate this caused and coincident or relation let us do one thing delete this also now define 1,050 okay now select these three lines there is solution and make relations symmetric now it is in center okay now select this outer line convert line connect with this line mirror this line okay now let's extrude it cancel first trim this outer circle okay it is coincident now select extra boss here and here choose 8mm but make sure melt midplane okay now see now select this phase is sketch normal and here also select corner rectangle and you start from this line and connect with outer outer line of this draw a center line define the distance 100.3 the width 8mm this is the actual rim or we'd get now select mirror select this and mirror about this line okay now again choose now I start from this point up to this line define the width 8mm okay now we will make one relation select these three lines and make relations a metric okay now these three geometries are created now we will now these three strips or we'd get created here so let's extrude it and extrude up to choose here surface select this outer surface and make sure it is unmerge result because this is the wid gate and another part of this tank select okay that's it now choose this plane plane number three Bearer and select the bodies select this three bodies separately select okay now you can see it is mirror now select write plane mirror now here we will select select first feature this body then part and mirror select okay now see it is mirror so this plane number third you can hide now the base is ready see this is the base of pressure vessel or tank the base is ready now we will add some flange and some hole in manhole here we will change the color steel the whole body so it will look visible okay this brush is brushed steel it looks nice now select this face is sketch normal and here we will create the holes first draw a circle and create the diameter 755 mm okay select this circle and make as a construction geometry now draw a circle here and keep the diameter 30 mm okay choose circular pattern select the center point and here select this circle and increase number of holes make number of holes 30 30 number of holes we want okay now select extruded cut and here choose up to next see beyond back side okay now the manhole cover holes also created always keep prospect - so the ratio looks real now here we will make some hole for gauges or pressure gays or or men there are many gauges in pressure vessel so choose front plane plane and create one geometry just beyond the 650 mm okay select this plane sketch normal draw a vertical and horizontal line select line draw a line here select 40mm select offset entity key 5mm and select inside okay and define the width and length for 25mm and the length from this line keep 195 mm okay now just select we want to mirror it select both the circle mirror with this line okay now let's select extruded boss select reverse direction and make sure it should be inside the tank now it's inside the tank make to 80 okay now again choose the same plane sketch extruded cut and here delete and select this inside circle okay now the hole is created inside the face now we want to just mirror it so choose right plane mirror and select this cut out and extruded body she is going to mirror here okay now see it's mirror now you can hide this plane first we will save our this picture go to desktop create a folder Pressure Vessel and select this first part tank or vessel now here we will make some hinge part for the locking of this manhole so we will create first one plane select this or let's select this phase plane make hundred 120 mm okay now select this plane a sketch normal again and choose here this line draw a vertical and horizontal line okay select line select this line I think not this line we should identify at this select this is inside line again choose a line it's not going to select up to this line select this three line and make relation it should be symmetric first make what horizontal and this one vertical now let us try to make a relation symmetric 100 by 140 select corner radius 30 mm okay choose offset entity 10 select this line inside okay now close the geometry exit choose here now here you can see we created this geometry here select extruded boss select this face choose here midplane 70 okay now select this face is sketch normal and draw a circle here first draw a center line this end to this end now select circle and draw a circle keep the diameter 70 mm draw one more circle and keep the diameter 48 mm okay and select extruded boss and extrude up to 8 mm only okay see that's it now select we want to mirror this so do one thing we will choose top plane mirror and select this extruded part see is going to mirror here okay now see it's mirror now again choose this is sketch extruded curtain and here select inside circle and select extruded cut up to okay but we want to cut through all so edit and this one chews through all see it is going down okay now the hole is created that's it now hide this plane now select this face is sketch normal and here we will create some flanges keep the diameter 180 mm again draw one more circle choose here for construction and define 80 mm selects circle keep diameter 20mm select Lee's pattern select this as a center point for numbers okay now select this outer circle circle of pipe and convert it now we will extrude this and keep up to 12 13 mm okay now see the flange is ready now we will just do it we will mirror this flange first mirror against top plane okay select geometry pattern can tell it and do one thing just unmerged his body edit this flange okay it's already and merged now try to mirror top plane mirror and select here body and choose flange now is going to mirror see it's mirror now now choose right plane mirror select this body and this body okay see the flanges are mirror in top face also we will create a flange keep 220mm create one more circle 175mm and draw a circle with diameter of 30 mm keep 25mm select the circle endpoint delete and select this point as a center point okay this outer pipe circle converted and this inside circle construction line now select extruded boss and up to 15 mm okay now this is the top level flange now here also the flanges keep 220mm keep 170 and draw a circle here 25 daya select this circle as a construction geometry choose linear circular pattern select here circle and point here select the center of this select okay now this one is created now we will try to copy here this whole portion so do one thing choose linear pattern select this all and keep the dimension 600mm see it is going to transfer here okay now select this outer circle convert here also convert now the same has drawn draw one circle here now this we will extrude it now and extrude up to 15mm okay now the last flange we will try this circle this pipe keep the diameter 220 and here draw one more circle and draw a small circle now let us keep this 17025 choose circular pattern select the circle and select the center point this one select this outer pipe daya converted construction geometry now select extruded boss and keep 15mm merge okay now all the pipe outlets flanges are created now see our vessel is ready almost now save now in next part we will create the manhole cover and a lifting hook you now here the next part is manhole cover so let's start choose front plane select horizontal and vertical lines let us start from here and connect with this point now let us assign the dimension 400 6.4 mm 34 mm and this one 3 mm and define this length 60 3.9 mm okay now select the Volvo boss place select this line as a axis okay now define the material steel brushed steel or let's make a stand but brushed steel is quite better now select this face sketch normal and here we want to create some holes first draw a path choose for construction geometry and 755 mm select circle and draw one circle here and keep the diameter 30 mm okay now choose your circular pattern select this circle and draw up to 30 holes okay now select extruded cotton and choose up to next okay now see the bolt hole created this is the hole for bolt now again choose the same surface sketch and here we want to create some choose line draw a vertical line select this line convert select circle 32mm the distance from here to this point take it down this end up to coincide here now define the gap 13 mm okay select the star point define two star points here exit define the gap 120 mm okay select both these star points and center line and make relation I think we have to define one by one let trim outside line I think the whole deleted return back select spline choose three-point are correct with this line wearer now select this both the point tangent choose trim entity and trim this outer part okay tangent this point little drag this coincide with this okay now select a line choose offset entity select this circle and keep distance 5mm now connect this line with this point again choose and same this point up to this now to stream entity and delete outer portions ok this geometry is sufficient for us select extruded boss select here up to surface select this back surface ok added and here choose unmerge result now it is looking better and visible now this is the manhole cover save this part Pressure Vessel part number two manhole cover now here we forget to add one more thing we will add here some lifting hook material so choose front plane sketch normal draw a center line and keep the distance 20 point 45 select circle and draw a big circle select butter center point arc select this point as a center and draw the circle up to up to here now let's define the diameter keep radius radius here we will select 74 by 2 that's it now select line and draw a vertical line from this and define the length 280 mm that's it now define the distance from Center Point keep 6mm okay now here choose sketch 5mm and select this end okay now exit now we will define one plane here first do one thing choose top plane plane and select this point now here we define the plane okay now select this plane a sketch normal and draw a circle here select this this is the exact PowerPoint and define the diameter 14 mm okay now exit now we will try to make extrude command soup to boss base command profile selected just select the path select okay something missing so do one thing add it make bigger 10 mm exit that's it now see now hide this plane now the manhole with lifting hook now save as now let's go for the next part you now the left next part is third part lifting support lifting accessories so select front plane a sketch select line draw a geometry now less left define this geometry 798 mm by 400 mm okay now exit from the geometry now again choose top plane a sketch select circle and draw a circle here and keep the diameter 48 mm now exit select ship boss/base now the sea this is calculated and here choose thin feature keep 3 mm but inside okay assign the material polished steel now see now we want to make one support here so select this line 45-degree plane select the same plane okay now select this plane sketch normal and draw a circle here okay select extruded boss up to next one direction select direction to up to next and choose your thickness keep 3mm - mmm inside select okay now see the support is created now hide this plane select top plane select a centerline and draw a circle here key 14mm and the distance from outer line keep 23 point 65 0.15 ok and select x2 dead cut we want to cut through all you want to make a hole here okay now see the hole is created now save this part part number three lifting support okay now let us start the assembly of Pressure Vessel you now here we will start the assembly of Pressure Vessel so select new assembly and here the assembly window open let first browse the first part choose our file from Pressure Vessel select first vessel keep plain background that's it now insert the next part lifting support make Matt select this hole and this okay define the gap 25 mm okay now see it is rotating here and there now insert the last part manhole cover first rotate the manhole cover select ok select this rod coincident this is co centric relation okay now you can see it is rotating like this manually now here we will make one relation select this face and this face Co centric relation okay now see our manhole is fixed just select perspective view choose section view or we will define select the front view and vessel front view but first right-click float now choose front plane mat okay top plane end of plane of met okay now the last one right plane and right plane of tank met okay now our geometry in perfect Center center of the assembly just check section view see this is the whole of half view of pressure vessel I hope you enjoyed this tutorial please subscribe our channel for more video and more projects in SolidWorks and thanks for watching you
Info
Channel: CAD CAM TUTORIAL
Views: 183,941
Rating: undefined out of 5
Keywords: Solidworks, tutorial, How, to, make, Pressure, Vessel, in, How to make, How to make Pressure Vessel, Pressure Vessel
Id: XkP8xTNrsDw
Channel Id: undefined
Length: 75min 14sec (4514 seconds)
Published: Fri Sep 30 2016
Related Videos
Note
Please note that this website is currently a work in progress! Lots of interesting data and statistics to come.