In December 2019, the City of Fort Lauderdale,
Florida experienced a series of catastrophic ruptures in a critical wastewater transmission
line, releasing raw sewage into local waterways and neighborhoods. Recognizing the need for
improvements to their aging infrastructure, the City embarked on a plan to install
a new pipeline to carry sewage from the Coral Ridge Country Club pumping station
across 7 miles (or 12 kilometers) to the Lohmeyer Wastewater Treatment Plant.
But just drawing a line on the map hides the enormous complexity of a project
like this. Installing an underground pipeline through the heart of a major urban area while
crossing three rivers is not a simple task. Underground utilities are usually installed by
a technique known as trenching. In other words, we excavate a trench down from the surface, place
the line, backfill the soil, and repair whatever damage to the streets and sidewalks remains. That
type of construction is profoundly disruptive, requiring road closures, detours, and pavement
repairs that never quite seem as nice as the original. Trenches are also dangerous for the
workers inside, so they have to be supported to prevent collapse. Beyond the human risk,
in sensitive environmental areas like rivers and streams, trenching is not only technically
challenging but practically unachievable because of the permits required. In fact, trenching
in urban areas to install pipelines these days is for the birds. When the commotion of
construction must be minimized, there are many trenchless technologies for installing pipes
below the ground. One of those methods helped Fort Lauderdale get a 7-mile-long sewer built in less
than a year and half, and is used across the world to get utility lines across busy roadways and
sensitive watercourses. I’m Grady and this is Practical Engineering. On today’s episode, we’re
talking about horizontal directional drilling. This video is sponsored by Curiosity
Stream and Nebula. More on them later. If you’ve ever seen one of these machines on
the side of the road, you’ve seen a trenchless technology in action. Although there are quite
a few ways to install subsurface pipelines, telecommunication cables, power lines, and sewers
without excavating a trench, only one launches lines from the surface. That means you’re much
more likely to catch a glimpse. Like laparoscopic surgery for the earth, horizontal directional
drilling (or HDD) doesn’t require digging open a large area like a shaft or a bore pit to get
started. Instead, the drill can plunge directly into the earth’s surface. From there, horizontal
directional drilling is pretty straightforward, but it’s not necessarily straight. In fact, HDD
necessarily uses a curved alignment to enter the earth, travel below a roadway or river,
and exit at the surface on the other side. Let me show you how it works and at the end, we’ll
talk about a few of the things that can go wrong. The first step in an HDD installation is
to drill a pilot hole, a small diameter borehole that will guide the rest of the
project. A drill rig at the surface has all the tools and controls that are needed.
These rigs can be tiny machines used to get a small fiber-optic line under a roadway or
colossal contraptions capable of drilling large-diameter boreholes for thousands
of feet at a time. As such, many of the details of HDD vary across projects, but the
basic steps and equipment are all the same. As the drill bit advances through the earth,
the rig adds more and more segments of pipe to lengthen the drill string. Through this pipe,
drilling fluid is pumped to the end of the string. Drilling fluid, also known as mud or slurry,
serves several purposes in an HDD project. First, it helps keep the drill bit lubricated and
cool, reducing wear and tear on equipment and minimizing the chances of a tool breaking
and getting stuck in the hole. Next, drilling fluid helps carry away the excavated soil or rock,
called the cuttings, and clear them from the hole. Finally, drilling fluid stabilizes and seals
the borehole, reducing the chance of a collapse. I have here an acrylic box partly full
of sand, a setup you’re probably quite familiar with if you follow my channel. Turns
out a box of sand can show a lot of different phenomena in construction and civil engineering.
Compared to soils that hold together like clay, sand is the worst case scenario when it comes
trying to keep a borehole from collapsing. If I pull away this support, the simulated
borehole face caves in no time. If I add groundwater to the mix, the problem is even
worse. Pulling away the support, the wall of my borehole doesn’t stand a chance. Let me
show you how drilling fluid solves this problem. I’m mixing up a handcrafted artisanal batch of
drilling mud, a slurry of water and bentonite powder. This is a type of clay created by
volcanic ash that swells and stays suspended when mixed with water. It’s pretty gloopy stuff,
so it gets used in cosmetics and even winemaking, but it’s also the most common constituent in
drilling fluids. If I add the slurry to one side of the demo, you can see how the denser
fluid displaces the groundwater. It’s not the most appetizing thing I’ve ever put on camera, but
watch what happens when I remove the rigid wall. The drilling fluid is able to support the face
of the sand, preventing it from collapsing. In addition to supporting the sand, the drilling
fluid seals the surface of the borehole to reduce migration of water into or out of the interface.
In most HDD operations, the drilling fluid flows in through the drill string and back out of the
borehole, carrying the cuttings along toward the entry location where it is stored in a tank or
containment pit for later disposal or reuse. So far HDD follows essentially the same steps as
any other drilling into the earth, but that first ‘D’ is important. Horizontal directional
drilling means we have to steer the bit. The drill string has to enter the subsurface from
above, travel far enough below a river or road to avoid impacts, evade other subsurface
utilities or obstacles below the ground, and exit the subsurface on the other side
in the correct location. I don’t know if you’ve ever tried to drill something, but
so far when I do it, I’ve never been able to curve the bit around objects. So how is it
possible in horizontal directional drilling? There are really two parts to steering a drill
string. Before you can correct the course, you need to know where you are in the first
place, and there are a few ways to do it. One option is a walkover locating device that
can read the position and depth of a drill bit from the surface. A transmitter behind the bit
in the drill string sends a radio signal that can be picked up by a handheld receiver. Other
options include wire-line or gyro systems that use magnetic fields or gyroscopes to keep track
of the bit's location as it travels below the surface. Once you know where the bit is,
you can steer it to where you want it to go. I’ve made up a batch of agar, which is a
translucent gel made from the cell walls of algae. I tried this first in the same acrylic box,
but the piping hot jelly busted a seam and came pouring out into my bathtub, creating a huge mess.
So, you’ll have to excuse the smaller glassware demo. My simulated drill string is just a length
of wire. There are two things to keep in mind about directional drilling: (1) Although they seem
quite rigid, drill pipes are somewhat flexible at length. If I take a short length of this wire
and try to bend it, it’s pretty difficult, but a longer segment deflects with no problem. And, (2)
you don’t have to continuously rotate the drill string in order to advance the borehole. You can
just push on it, forcing the bit through the soil. My wire pushes through the agar without much
force at all, and a drill string can be advanced through the soil in a similar way, especially
when lubricated with water or drilling fluid. The real trick for steering a drill string is
the asymmetric bit. Watch what happens when I put a bend on the end of my wire and advance
it through the agar. It takes a curved path, following the direction of the bend. If I rotate
the wire and continue advancing, I can change the direction of the curve. The model drill string is
biased in one direction because of the asymmetry, and I can take advantage of that bias to
steer the bit. I can steer the string left, then rotate and advance again to steer the bit
to the right. I’m a little bit clumsy at this, but with enough control and practice, I could
steer this wire to any location within the agar, avoid obstacles, and even have it
exit at the surface wherever I wanted. This is exactly how many horizontal directional
drills work. The controls on the rig show the operator which way the bit is facing. The
drill string can be rotated to any angle (called clocking), then advanced to change the
direction of the borehole. Sometimes a jet nozzle at the tip of the bit sprays drilling fluid
to help with drilling progress. If the nozzle is offset from the center, it can help create a
steering bias like the asymmetric bit. Just like the Hulk’s secret is that he’s always angry, a
directional drill string’s secret is that it’s always curving. The rig operator’s only steering
control is the direction the drill string curves. And hey, if that sounds like something you’d like
to try for yourself, my friend Dan Shiffman over at the Coding Train YouTube channel built a
2D horizontal directional drilling simulator. This is an open-source project, so
you can contribute features yourself, but it’s also really fun if you
just want to play a few rounds. If you’re into coding or you're wanting to get
started, there is no better way than working through all the incredible and artistic examples
Dan comes up with for his coding challenges. Go check him out his video on HDD after
this one, and tell him I sent you. Once the drill string is headed in the right
direction, it can just be continuously rotated to keep the bit moving in a relatively
straight line. The pilot hole for an HDD project is just an exercise in checking the
location and adjusting the clock position of the drill string over and over until
the drill string exits on the other side, hopefully in exactly the location you
intended. But, not all soil conditions allow for a drill string to simply
be pushed through the subsurface. Rocky conditions, in particular, make
steering a drill rig challenging. An alternative to simply ramming the bit through
the soil is to use a downhole hydraulic motor. Also known as mud motors, these devices convert
the hydraulic energy from the drilling fluid being pumped through the string to rotate a
drill bit that chews through soil and rock. This allows for faster, more efficient drilling
without having to rotate the whole drill string. The housing of the mud motor is
bent to provide steering bias, and the drill string can be clocked to
change the direction of the borehole. Once the pilot hole exits on the other side, it
has to be enlarged to accommodate the pipe or duct. That process is called reaming. A reamer is
attached to the drill string from the exit hole and pulled through the pilot toward the drill
rig to widen the hole. Depending on the size of the pipe to be installed, contractors may ream
a hole in multiple steps. The final reaming is combined with the installation of the pipeline.
This step is called the pull back. The pipe to be installed in the borehole is lined up on
rollers behind the exit pit. The end of the pipe is attached to the remaining assembly, and the
whole mess is pulled with tremendous force through the borehole toward the rig. Finally, it can be
connected at both ends and placed into service. That’s how things work when everything goes
right, but there are plenty of things that can go wrong with horizontal directional drilling too.
Parts of the drill string can break and get stuck in the pilot hole. Drilling can inadvertently
impact other subsurface utilities or underground structures. The pipeline can get stuck or damaged
on pullback. Or, the borehole can collapse. The controversial Mariner East II pipeline in
Pennsylvania experienced a litany of environmental problems during its construction between 2017
and 2022. Most of those problems happened on HDD segments of the line and involved
inadvertent returns of drilling fluid. That’s the technical term for the situation when
drilling fluid exits a borehole at the surface instead of circulating back to the entrance
pit. The inadvertent returns in the Mariner East II line created water quality issues in
nearby wells, led to sinkholes in some areas, and spilled drilling fluid into sensitive
environmental areas. The pipeline owner was fined more than $20 million over the course of
construction due to violations of their permits, and they are still mired in legal battles and
extreme public opposition to the project to date. In the case of Mariner East II, most of
the drilling fluid spills were partially related to the difficult geology in Pennsylvania.
Clearly HDD isn’t appropriate for every project. But in most cases, trenchless technologies
are the environmentally-superior way to install subsurface utilities because they
minimize disruptions on the surface to the people in urban areas and sensitive
habitat around rivers and wetlands. This video’s sponsor is actually two sponsors,
Curiosity Stream and Nebula, which is awesome because you get access to both for less than the
price of similar services. Nebula’s a completely ad-free streaming service built by and for your
favorite independent creators like Wendover Productions, Real Engineering, and me. It’s a way
for us to try new ideas and longer videos that might not work well on ad-supported platforms
like YouTube. My videos go live there the day before they go on YouTube, and one of my favorite
parts of Nebula is rewatching some of my favorite creators’ back catalogs of videos without any
ads. And, we’re super excited to continue our partnership with Curiosity Stream, a service with
thousands of documentaries and non-fiction titles on pretty much every subject you can imagine.
Curiosity Stream loves independent creators and wants to help us grow our platform, so they’re
offering free access to Nebula when you sign up at CuriosityStream.com/practicalengineering. I know
there are a lot of streaming services right now, and if you add them all up it would be hundreds
of dollars a month. That’s why this bundle is such an awesome deal. You get access to
two platforms (Nebula and Curiosity Stream) for less than $15 a year. I have kids,
so when we have the TV on in house, I want to make sure it’s something that expands
their minds. Curiosity Stream has a huge library of kid-friendly content, like this series that
covers every single national park in the US. This is the stuff that used to be on TV
when I was a kid, and it’s so good. Plus, watch Sam from Wendover Productions try to break
the law while evading his production team in the Nebula-exclusive series, Crime Spree. This bundle
is a great way to support my channel and a whole host of your other favorite educational creators.
Plus it’s just a good deal. Do us both a favor and click that link in the description. Thank you
for watching, and let me know what you think
