It is undoubtedly unintuitive that water
flows in the soil and rock below our feet. A 1904 Texas Supreme Court case famously noted
that the movement of groundwater was so “secret, occult and concealed” that it couldn’t be
regulated by law. Even now, the rules that govern groundwater in many places are still well
behind our collective knowledge of hydrogeology. So it’s no surprise that misconceptions
abound around water below the ground. And yet, roughly half of all drinking water
and irrigation water used for crops comes from underneath the surface of the
earth. You can’t really look at an aquifer, but you can look at a model of one I built in my
garage. And at the end of the video, I’ll test out one of the latest technologies in aquifer
architecture to see if it works. I’m Grady and this is Practical Engineering. In today’s episode,
we’re talking about groundwater and wells. This video is sponsored by Curiosity
Stream and Nebula. More on them later. Not all water that falls as precipitation runs off
into lakes and rivers. Some of it seeps down into the ground through the spaces between soil and
rock particles. Over time, this infiltrating water can accumulate into vast underground reservoirs. A
common misconception about groundwater is that it builds up in subterranean caverns or rivers.
Although they do exist in some locations, caves are relatively rare. Nearly all groundwater
exists within geologic formations called aquifers that consist of sand, gravel, or rock
saturated with water just like a sponge. It just so happens you’re watching the number
one channel on the internet about dirt, and there are a lot of interesting things
I can show you about how aquifers behave. I built this acrylic tank in my garage to
illustrate some of the more intriguing aspects of groundwater engineering. I can fill it up with
sand and add blue dye to create two-dimensional scenarios of various groundwater conditions. It
also has ports in the back that I can open or close to drain various sections of the model.
And, on both sides, there’s a separation that simulates a boundary condition on the aquifer.
Water can flow through these dividers along their height. Most of the shots you’ll see of this have
been sped up because, compared to surface water, groundwater flows quite slowly. Depending on
the size of soil or rock particles, it can take a very long time for water to make its way
through the sinuous paths between the sediments. The property used to characterize this speed
is called hydraulic conductivity, and you can look up average values for different types of soil
online, if you’re curious to learn more. In fact, different geologic layers affect the presence
and movement of groundwater more than any other factor, which is why there is so much variability
in groundwater resources across the world. Like all fluids, groundwater flows from areas
of high pressure toward areas of low pressure. To demonstrate this, I can set the left boundary
level a little higher than the one on the right. This creates a pressure differential across the
model so water flows from left to right through the sand. I added dye tablets at a few spots so
you can see the flow. This is a simple example because the pressure changes linearly through
a consistent material, but any change in these conditions can add a lot of complexity. In purely
mathematical terms, you can consider this model a 2D vector field because the groundwater can
have a different velocity - that is direction and speed - at any point in space. Because of
this, there are a lot of really neat analogies between groundwater and other physical phenomena.
My friend Grant of the 3Blue1Brown YouTube channel has an excellent video on vector field mathematics
if you want to explore them further after this. We often draw a bright line between groundwater
and surface water resources like rivers and lakes because they behave so differently. But water
is water. It’s all part of the hydrologic cycle, and many surface waters have a
nexus with groundwater resources, meaning that changes in groundwater may impact
the volume and quality of surface water resources and vice versa. Let me show you an example.
In the center of my model, I’ve made a cross section of a river. The drain at the bottom of the
channel simulates water flowing along the channel, in this case leaving my model. If I turn on
the pumps to simulate a high water table in the aquifer, the groundwater seeps into the river
channel and out of the model. The dye traces show you how the groundwater moves over time. If you
encounter a situation like this in real life, you might see small springs, wet areas of
the ground, and (during the winter) even icicles along slopes where the groundwater
is becoming surface water before your eyes. Likewise, surface water in a river can flow
into the earth to recharge a local aquifer. I’ve reconfigured my model so the pump is putting
water into the river and the outer edges of the reservoir are drained, simulating a low water
table. Some of the water in the river flows back out of the model through the overflow drain,
showing that while not all the water in a river seeps into the ground, some does. You can see
the dye traces moving from the river channel into the aquifer formation, transforming from surface
water into groundwater as it does. As you can see, surface water resources are often key locations
where underground aquifers are recharged. This is all fun and interesting, but much
of groundwater engineering has more to do with how we extract this groundwater for
use by humans. That’s the job of a well, which, at its simplest, is just a hole into which
groundwater can seep from the surrounding soil. Modern wells utilize sophisticated
engineering to provide a reliable and long-lasting source of fresh water. The basic
components are pretty consistent around the world. First, a vertical hole is bored into
the subsurface using a drill rig. Steel or plastic pipe, called casing, is
placed into the hole to provide support so that loose soil and rock can’t fall into the well.
A screen is attached at the depth where water will be withdrawn creating a path into the casing.
Once both the casing and screen are installed, the annular space between them and the bore
hole must be filled. Where the well is screened, this space is usually filled with gravel
or coarse sand called the gravel pack. This material acts as a filter to keep fine
particles of the aquifer formation from entering the well through the screen.
The space along the unscreened casing is usually filled with clay, which swells to
create an impermeable seal so that shallow groundwater (which may be lower quality) can’t
travel along the annular space into the screen. Wells use pumps to deliver water that flows into
the casing up to the surface. Shallow wells can use jet pumps that draw water up using suction
like a straw. But, this method doesn’t work for deeper wells. When you drink through a straw,
you create a vacuum, allowing the pressure of the surrounding atmosphere to push your beverage
upward. However, there’s only so much atmosphere available to balance the weight of a fluid in
a suction pipe. If you could create a complete vacuum in a straw, the highest you could draw a
drink of water is around 10 meters or 33 feet. So, deeper wells can’t use suction to bring
water to the surface. Instead, the pump must be installed at the bottom of the well so that it can
push water to the top. Some wells use submersible pumps where the motor and pump are lowered to
the bottom. Others use vertical turbine pumps where only the impellers sit at the bottom driven
by a shaft connected to a motor at the surface. All that pumping does a funny thing to an
aquifer. I can show you what I mean in the model. As water is withdrawn from the aquifer, it
lowers the level near the well. The further away from the well you go, the less influence
it has on the level in the aquifer. Over time, pumping creates a cone of depression around
the well. This is important because one well’s cone of depression can affect the capacity of
other wells and even impact nearby springs and rivers if connected to the aquifer. Engineers use
equations and even computer models to estimate the changes in groundwater level over time, based
on pumping rate, recharge, and local geology. One fascinating aspect of deeper aquifers
is that they can be confined. My model isn’t quite sophisticated enough to show
this well, but I can draw it for you. A common situation is that an aquifer exists at
an angle to the ground surface. It can recharge in one location, but becomes confined by a less
permeable geologic layer called an aquitard. Water flowing into a confined aquifer can
even build up pressure, so that when you tap into the layer with a well, it flows readily
to the surface (called an artesian well). It can happen in oil reservoirs as well, which is
why you occasionally see oil wells blow out. A part of the construction of wells that I didn’t
mention yet is the top. A well creates a direct path for water to come out of an aquifer, and
if not designed, constructed, and maintained properly, it can also be a direct path into the
aquifer for contaminants on the surface. In my model, I can simulate this by dropping some dye
into the well to represent an unwanted chemical spilled at the surface. Say some rainwater enters
too, washing the contaminant through the well into the aquifer. Now, as groundwater naturally
moves in the subsurface, it carries a plume of contamination along as well. You can see how
this small spill could spread out in an aquifer, contaminating other wells and ruining the resource
for everyone. So, wells are designed to minimize the chances of leaks. The uppermost section
of the annular space is permanently sealed, usually with cement grout. In addition, the
casing is often extended above the surface with a concrete pad extending in all directions
to prevent damage or infiltration to the well. We’ve been talking so much about how to get water
out of an aquifer, but there are some times where we want to do the reverse. Injection wells are
nothing new; deep belowground can be a convenient and out-of-the-way place to dispose of unwanted
fluids including sewage, mining waste, saltwater, and CO2. But until recently, it hasn’t been
a place to store a fluid with the intent of taking it back out at a later date.
Aquifer Storage and Recovery or ASR is a relatively new technology that can help
smooth out variability in water resources where the geology makes it possible. Large-scale
storage of water is mostly restricted to surface water reservoirs formed by dams that are expensive
and environmentally unfriendly to construct. With enough pressure, water can be injected through a
well into an aquifer. You can see on my model that introducing water to the well causes the level
in the aquifer to rise over time. Eventually, this water will flow away, but (as I mentioned)
groundwater movement is relatively slow. In the right aquifer, you won’t lose too much water
before the need to withdraw it comes again. Taking advantage of the underutilized
underground seems obvious, but there are some disadvantages too. You need a goldilocks
formation where water won’t flow away too fast, but is also not so tight that it takes super-high
pressure for injection. You also need a geologic formation that is chemically compatible with the
injected water to avoid unwanted reactions and bad tastes. Of course, you always have costs,
and ASR systems can be expensive to operate because the water has to be pumped twice -
once on the way in and again on the way out. Finally, you can have issues with speed. In many
places, the surplus water that needs to be stored comes during a flood - massive inflows that arrive
over the course of a few hours or days. A dam is a great tool to capture floodwaters in a reservoir
for later use. Injection wells, on the other hand, move water into aquifers too slowly for that.
They’re more appropriate where surplus water is available for long durations. For example, one
of the few operating ASR projects is right here in my hometown of San Antonio. When water demands
fall below the permitted withdrawals from our main water source, the Edwards Aquifer, we take the
surplus and pump it into a different aquifer. If demands rise above the permitted withdrawals,
we can make up the difference from the ASR. You can add more injection wells to increase the
speed of recharge, but above a certain pressure, some funny things start to happen: underground
formations break apart and erode in a phenomenon called hydraulic fracturing or just fracking.
Breaking apart underground formations of rock and soil has been a boon for the oil and gas industry.
But, just like that Texas groundwater in 1904, the regulation of fracking is mired in confusion and
controversy, in no small part because it happens below the surface of the earth, hidden from public
view. I’ll save those details for a future video. And if you’re eager to see the next Practical
Engineering episode as soon as possible, you should know that my videos go live on Nebula
before they’re released here on YouTube. Nebula’s a completely ad-free streaming service built
by and for your favorite independent creators like Wendover Productions, Real Engineering,
and me. It’s a way for us to try new ideas and longer videos that might not work well on
advertising-supported platforms like YouTube. And, we’re super excited to continue our partnership
with Curiosity Stream, a service with thousands of documentaries and non-fiction titles on
pretty much every subject you can imagine. Curiosity Stream loves independent creators and
wants to help us grow our platform, so they’re offering free access to Nebula when you sign
up at CuriosityStream.com/practicalengineering. I know there are a lot of streaming services
right now, and if you add them all up it would be hundreds of dollars a month. That’s
why this bundle is such an awesome deal. You get access to two platforms (Nebula and
Curiosity Stream) for less than $15 a year. I love space exploration, and Curiosity Stream has
a bunch of excellent documentaries on the topic, including this one on building the James
Webb Telescope that recently launched. Or, watch Sam from Wendover Productions try
to break the law while evading his production team in the Nebula-exclusive series, Crime Spree.
It’s a great way to support my channel and a whole host of your other favorite educational creators.
Plus it’s just a good deal. Do us both a favor and click that link in the description. Thank you
for watching, and let me know what you think!
