8.3.1.4 Packet Tracer - Implementing a Subnetted IPv6 Addressing Scheme

Video Statistics and Information

Video
Captions Word Cloud
Reddit Comments
Captions
hi firms so welcome to or in this video we are going to see the packet tracer activity implementing a subnet third ipv6 addressing scheme we will go through the objectives of this packet tracer our activity in part 2 1 a determine the ipv6 subnets and addressing scheme in party to configure the ipv6 addressing on routers and 2 pcs and to verify connectivity here is our scenario your network administrator wants you to assay in 5 is large 64 ipv6 subnets to the network shown in the topology right so here is our network here we can see the topology well your job is to determine the ipv6 subnets I say in ipv6 addresses to the routers and set the PCs to automatically receive ipv6 addressing your final step is to verify connectivity between ipv6 host we will come to part 1 it remind the ipv6 subnets and at the sinks came in that step 1 determine the number of subnets I needed so I start with the ipv6 subnet 2001 : DB 8 : AC ad : 0 0 C 8 double : star 64 and assign it to the r1 land attached the gigabyte Ethernet 0 star 0 as shown in the subnet table yes here we can see that for the rest of the ipv6 subnets increment the 2001 : DB 8 : AC ad : 0 0 CA double : / 64 subnet atras by 1 and complete the subnet table with the ipv6 subnet addresses here is our subnet table and here we can see the first her Trece for the r1 interface' gigabit ethernet 0/0 now we will increment this atrocity subnet access by 1 and we will write in this spreadsheet coming to these right I'm going to drag your right will copy that and here we are going to change the value submit' value increment Y 1 1 so it will become 9 so here I am going to copy these here it will be we know that after 9 it will be yeah so it's in the hexadecimal number right so we try to drag this right so we will copy and paste your onto here we have to change the subnet beam and the last one is will be C right now we will come to a step to a sane ipv6 are trusting to the routers I see in the first to ipv6 etre cells to r1 for the tool and links and the one link right I say in the first ipv6 our trust to r2 for the two lands I say the second ipv6 address for the one link and document the ipv6 addressing scheme in the addressing table yes here we can see our addressing table is incomplete so we have to complete our addressing table also now we are going to assign ipv6 addressing to this router r1 CL I write your enable configure terminal we will go to the interface Gigabit Ethernet 0/0 and now we are going to a say in the ipv6 address until we have to get the submitter trust your yes here we can see that I am going to copy these right so coming to CLI Here I am going to paste this actress so it's a subnet a trust now we have to uh say in the horse across here so here we'll the first a trust we will use your or that is one right here will give you 64 on Jeff yes now we will press ENTER now we will assert the link local être sir so we have to give ipv6 archers so the link local address is fe80 : : one and two this is a link local address right present now we are going to give nor should command here yes now we will come to the next interface so Gigabit Ethernet 0/1 so you will go to the interface Gigabit Ethernet to 0/1 and we will set the ipv6 address so we have to check the IP address for this interface so this is a subnet atrocity or I'm going to copy researchers yes so here I am going to paste this so here we are going to change the host here we are going to use the first usable ipv6 address so here we are going to give one present or now we will set the link local across here ipv6 actress if he 8 0 w : 1 and this is a link local now we are going to give a no-shit command now we will come to the interface serial 0 / 0 / 0 so we can go directly interface serial 0 / 0 / 0 and here we are going to set the ipv6 address so here is our serial 0/0 so our 0 subnet rasuu handling yes I am going to copy this address coming to CLI Here I am going to paste it here we are going to use the first useable ipv6 address so that's one right now we will set the link local address so IP v6 our trust that is fe80 double : one link-local and now we will give no command right now we will come to the router r2 so here we can see that the interfaces are Gigabit Ethernet 0 / 0 0 / 1 and we have a serial here yes 0 0 / 0 so coming to the router CLI write enable configure terminal we will go to the interface Gigabit Ethernet 0 / 0 and we will set the ipv6 address right so we have to get the extra subnet actress here we can see that I'm going to copy these subnet extras yes so here we are going to use the first usable ipv6 address these double colon 1 & 2 now we will assert the link look at local actress ipv6 Archers so here we can see in our addressing table it's mentioned safe e 8 0 w : - so we are going to set that note Auto configure we are going to give a Fe 8 0 w : - this is link local right now we are going to give nor shut command now we will configure the interface so Gigabit Ethernet 0 / 1 so interface Gigabit Ethernet 0 / 1 coming to the actress ipv6 trust now we will check these subnet atras here we can see that I am going to copy the Searchers coming back to CL I right here we are going to paste it now we will use the first usable ipv6 across your yes it's 1 now we will set the link local 'trust so here to give ipv6 our choice we have a Fe 8 0 w : 2 as link-local right now we will give an ocean command yes now we will go to the serial interface so interface serials eurostar 0/0 now here we are going to set the ipv6 address so we have to get the van Linga trust yes you're a tease coming to the CLI right oops remove this will give the IP our trust your this is subnet uh trust now we are going to use the next atrocity or we cannot use your one because we already given this address for the interface 0 0 / 0 / 0 on the device are 1 so we are going to use the next our trust that is to write press Enter now we are going to set the link local address ipv6 archers here we are going to give fe80 : : - this is a link local address now we will give no command yes now we are going to document this ipv6 addressing scheme in our addressing table here is our addressing table and coming to the device r1 yes your we can see the interface Gigabit Ethernet 0/0 we are saying the first IP are truss so I am going to copy these so here we use the first two usable IP v6 our trust that's one coming to the next interface so Gigabit Ethernet 0 / 1 here we can see the subnet address I'm going to copy that and here we use the first useable ipv6 address it's one right coming to serial 0 / 0 / 0 it's a one link here we can see the circuit extras yes and two here we use the first usable IP v6 address and also for the are too serious 0 / 0 / 0 we use the next just say I'm going to do that also here it's two right now we will come to Gigabit Ethernet 0/0 on our - here we can see that so here it will be the first usable ipv6 address it's one and coming to the Gigabit Ethernet 0 / 1 on our - here we can see that subnet occurs copy and paste your so I'm going to change the house portion right now we will come to a party to configure the ipv6 addressing on routers and PCs and verify connectivity in that step 1 configure the routers with ipv6 accessing so they're given a not here this network is already configured with some ipv6 commands that are covered in a later course at this point in your studies you only need to know how to configure ipv6 answers on an interface well right configure R 1 and R 2 with the ipv6 address you specified in that dressing table and to activate the interface so this is the way of giving here you can see that ipv6 address then we have to give the ipv6 address and / if --ax then we have to give the link local address ipv6 at first then the link local address then we have to give this word command chilling local so we have done already this now we will come to step to configure the pcs to automatically receive ipv6 addressing configure the 4 pcs for auto configuration it should then automatically receive full ipv6 addresses from the routers right we will do this now we will come to the first PC your PC one will go to desktop IP configuration here we are going to select ipv6 configuration Auto config yes so we will do on other pcs coming to PC 2 the stop here we are going to give auto-config coming to pc 3x top IP configuration auto-config coming to pc for a stove IP configuration Auto config right now we will go to a step 3 verify connectivity between the PCs each PC should be able to ping the other pcs and routers right we will verify this now first of all we will ping from pc1 to pc2 so we have to get the IP address of a pc to here we can see that ipv6 address so all the pc to pc 3 and PC for ipv6 address so i noted on north pad coming to pc 1 will copy this a pc to ipv6 address coming to pc 1 command prompt to now we will pink to pc - yes we are getting the replay now we will get the pc 3 ipv6 address pink a pc 3 ipv6 address yes we are getting the replay now we will go to we will get the pc for ipv6 address here it is right we will ping it bring to the ipv6 address of pc 4 years we are getting the replay well so in this packet tracer activity we didn't mind the ipv6 up nets then we assign into ipv6 addresses to the routers and we set the pieces to automatically receive I P v6 addressing my difference if you have any doubt please comment below also if you like my video give a thump and don't forget to subscribe the channel so that you will get latest uploading video info into your Gmail thank you
Info
Channel: Tech Acad
Views: 45,256
Rating: undefined out of 5
Keywords: IPv6
Id: eEBN5hsW680
Channel Id: undefined
Length: 15min 41sec (941 seconds)
Published: Fri Sep 22 2017
Related Videos
Note
Please note that this website is currently a work in progress! Lots of interesting data and statistics to come.