2.2.5.5 Packet Tracer - Configuring Floating Static Routes

Video Statistics and Information

Video
Captions Word Cloud
Reddit Comments
Captions
- so welcome to all in this video we are going to see the packet tracer activity configuring floating static routes this packet tracer activity is from a CCNA routing and switching here we can see the topology and also we can see the packet tracer activity in this packet tracer activity we are going to configure an ipv4 floating static route just failover to the ipv4 floating static route and the configure and test to fail over for an ipv6 floating static route we will come to a path to one your configure and ipv4 floating static route so before that we will configure an ipv4 static default route configure exactly connected static default or route from edge router yes here we can see edge router to the Internet the primary default route should be through is p1 yes here we can see is p1 so the primary route from this edge devices PCA and PCB to internet I mean to this web server is is p1 you will come to edge router anti-vehicle configure this default route enable configure terminal and we will give I P route 0.0.0.0 space 0.0.0.0 and so we have to specify the exit interface so we have to check out the toll to the primary the default route I mean the primary default route is is p1 to reach to this Internet so here we will verify the interface exit interface yes it is the CDL 0 / 0 / 0 we will set that here serial 0/0 slot 0 next teaser display the contents of the routing table verify that the default route is visible in the routing table yes so we can see using the show command show IP route on edge router yes coming to its router yes we are in privileged more will give show IP route until we can see yes here we can see the default route and the exigence of phase zero zero zero zero zero what command is used to trace a path from a PC to a destination yes we have a command called trace earth to trace a path from a source to a destination next we can see now from PC a trace the route to the web server ok coming to the topology here we can see the device PCA and here is our web server right the route should start at the default gateway exactly so that is 192.168.10.10 so for this interface the default gateway for this PC a and to go through the tender tender 10.1 address yes if you see this interface that is serial 0 0 0 on its rotor the IP address is a 1000 1000 10.2 so here this IP address enter 10 to 10 dot 1 is obviously the IP address of this interface a serial 0 0 0 star 0 on is p1 ok now if not check your static default route configuration but before coming to pca we can see the IP address of this web server a one nine eight dot zero dot zero two one zero so we are going to try cert to this web server from pca coming to pc a command prompt - here we are going to give a trace search and to the IP answers for destination IP address 19.0 dot 0 one-zero yes here we can see it is tracing route and here we can see the IP address this IP address offer the default gateway of this PC and here we can see the IP address 10.10 door 10.1 yes as a trolled under this is the destination IP address and trace completed well now we will go to a step to configure an ipv4 a floating static row yes now we will see what is protein static route now what is that mean straight to distance of a static route yes we know that ministrations of a static route I mean the recursive is obviously 1 next is configure a directly connected floating static default route with an administrative distance of 5 the route should point to ISP - yes here we can see we are going to set the static default route with administrative distance this is nothing but the floating static route coming to the topology here we can see we are going to set the floating static defaulter route through is pa2 so here we have to check the exit interface so that is the serial and we'll check it here serial 0 / 0 / 1 come on now we will come to yet rotor enable configure terminal here we are going to give IP route 0.0.0.0 space 0.0.0.0 and here the exit interface is serial 0 / 0 / 1 and here we can see we can specify the distance metric for this route so as i specified here we are going to give 5 next is view the running configuration and to verify that the ipv4 floating static default route is there as well as the ipv4 static default route okay we will come to a Giroux taranta we will verify that so running config yes we will verify that now yes here we can see that this is the primary default route and also we can see the floating default route what we set now we will go to the next display the contents of the routing table is the ipv4 floating static route visible in the routing table explained obviously it will not but we will verify that coming to its router it will give show IP route yes here we can see the how only the primary default route yes through serial zeros are zeros are 0 which is going through is p1 to the Internet yes here the floating static route is not visible in this routing table keep in mind rotors will only place the best path in the routing table so this I mean the floating static route will be will only be visible in the routing table when the primary route goes down great joke now we will come to party to just sail over to the ipv4 floating static route on edge the route are administratively disabled the exit interface of the primary route yes here we can see on edge router the primary route is through serial zeros are 0 0 0 and we are going to disable this interface using Nauset command coming to the edge router will go to the interface before that we have to go to the global configuration mode configure terminal interface serial 0/0 smart 0 and we are going to set on it using shuttle and we're afraid that the ipv4 floating static route is now in the routing table okay we will verify that now you show IP route and to here we can verify years now we can see the exit interface is serial 0 / 0 / 1 it's through ie sp2 to the internet yes you can see when we disable this path through is p1 to the internet it takes over through serial 0 / 0 / 1 through is p2 to the Internet now we will trace the route from PCA to the web server yes so we are going to trace from PCA to this web server obviously it will go through is p2 to this web server we will see the IP access of serial 0 / 0 / 1 that is 1/10 or 10,000 or 6 we will come to PC a command from here we are going to give tray cert yes here we can see the IP address 10 to 10 to 10.5 yeah previously it was the 10 to 1000 10.1 now it is going through is b2 to the internet timing to this observer yes hmm with the backup route work yes obviously it works now if not wait a few more seconds so for convergence and then retest if the backup route is still not working investigate to your floating static route configuration ok now anyway in this activity it is working now restore connectivity to the primary route yes so we will enable this interface seriously row / 0 / 0 on edge router so that it will a traffic through is p1 to the Internet configure terminal we will go to the interface serial 0/0 star 0 and we will give a no-shit command next to user trace the route from PCA to the web server to verify that the primary route is re stored yes we will verify that coming to PCA will give tray cert and here we can see yes now we can see it goes through is p1 to the Internet and out enter 10.1 well now we will come to part 2 3 that is configure and test failover to an ipv6 floating static route yes previously we have seen for ipv4 now we are coming to ipv6 configure an ipv6 a floating static route here the ipv6 static the folder root 2 is p1 is already configured so what is our duty configure an ipv6 floating static default route with an administrative distance of 5 so we have to I mean we are going to configure your floating ipv6 floating static default route with an estate to distance of 5 and here we can see the root should point to ipv6 access here they given the access of ISP to now we will come now we will come to its rotor ok enable so before going to I TV 6 a floating static route I am going to check show ipv6 interface briefs so that we can check the IP access or serial 0 / 0 / 1 here we can see the ipv6 address off the interface 0 0 / 0 / 1 DB h : a : 2 w : true so we have to specify the next to hope actress that is the IP address or the IP address offer the router in this is p2 in the same network so that is a two double : one we will set that now configure terminal here we are going to give ipv6 route double colon slash zero and we are going to specify that next hop Archos ipv6 up source of next hope that is two thousand to one I will copy from there okay here it is As I am going to copy that we will paste it yes until now we will specify administrative distance as five next is a view the running configuration to verify that the ipv6 the floating static default route is now listed under the ITD's ecstatic default route yes we will verify that now coming to the router here we are going to give so running config and we are going to verify our discipie v6 for floating static route yes here we can see here we can see the default route and here we can see floating a default route without mr. distance of sign well now we will come to step two just failover to the ipv6 floating static route on edge router administratively disabled the exit interface of the primary route yes so in this router we are going to disable this interface so that we will have we can communicate through is p2 we will come through its rotor no will disable it to enable configure terminal we are going to the interface serial 0 so R 0 0 0 and we are going to shut it down now verify that the ipv6 a-floating static road is now in the routing table okay we will verify that okay show IP v6 route here we are going to years here we can see that floating static route with administrator distance 5 now we will trace the route from PCA to the web server ok so we are going to trace from PCA to this web server and here is the address 2001 : DB 8 : f : f : f w : 10 okay we will copy that Atris yes here it is now we'll come to PC a you give tray search and the IP address ipv6 address yes here we can see here we can see the details so the first two ipv6 address is the default gateway of a PC a that is the ITV 6 address or for this interface of adjure router and to the second one we can see this is an ipv6 address of the router in is p2 which is connecting to edge router and so you can see this is the ipv6 address of our web server yes did the backup route work yes it works so if not to wait a few more seconds for convergence and then retest if the backup route is still not working investigate your floating starter route configuration okay here it is working perfectly now we will restore connectivity to the primary route we have to go to edge router enable configure terminal we have to go to the interface serial cero cero cero until we are going to give a no-shit command we can see these interfaces up now also we will verify that so ipv6 route yes here we can see that finally trace the route from PCA to the web server to verify that the primary route is all restored we will come to PCA and we will trace to this web server so coming to command prompt we already given touch yes yes here we can see the network changes a colon one here we previously it was a colon true now it is changed into a primary default route well great job we configured the packet tracer activity configuring floating static routes successfully runs if you have any doubt a please comment below also if you like my videos give a thump also you can subscribe my channel to get future uploading video information in to your Gmail stay tuned bye bye
Info
Channel: Tech Acad
Views: 42,854
Rating: undefined out of 5
Keywords: floating static routes
Id: GMUR3p1Qrds
Channel Id: undefined
Length: 19min 7sec (1147 seconds)
Published: Sat Jun 24 2017
Related Videos
Note
Please note that this website is currently a work in progress! Lots of interesting data and statistics to come.