【セリア】【キャンドゥ】 セリア火起こし器をシンデレラフィット 3か所の100均材料2個DYIで、炎がキレイな二次燃焼ウッドガスストーブへカスタム！本家ソロストーブに近づきたい！キャンプ道具、プチプラ

Thank you for watching kurukoya. This is my first challenge, but I would like to process it to make camping goods. Yes , let's start with the material introduction. This is a ceria fire starter, a new product this spring. Originally, it is used as a fire starter, but it is a good subject for making a secondary combustion stove, so I would like to take on this challenge. And this is also a powder sieving device purchased from Ceria. This is what you use when making sweets. Shake like this! I would like to use this as a substitute for the combustion chamber. And the other last material is here. Well, this is an oil pot purchased by Can Do. This time, I will use this inner lid. The reason is that the mouth of the fire starter has a feeling of resistance, but it fits tightly ! After that, Cinderella fits! So here is the image of this secondary combustion stove! Good masking tape should be left as easy to peel off when peeled off by No Yes Well can I have it a little folded at this last use so do with a material which is in as much as possible the house you dressing to 1.5cm the vinyl tape from the top in the Yes I got a straight line with the feeling Yes! Next, I will make a mark with magic, but since I will make 6 holes, I would like to make a mark while imagining an equilateral triangle . If you want to hit that 8 places, you can stack two squares. .. .. Well, I think I can arrange it here and there. If the image doesn't match , I'll sprinkle it with alcohol many times, so I think this is better. Then I'll mark it. Marking has been completed all around. Because on top of the vinyl tape, I So this was the end to which I think Yes safely work up here and want this also to do with the extent indelible you I will drill holes in the place that put the earlier mark this time to dent stick did not like of you to be the best of the highlight I bought this hole saw! Well, I'd like to make a hole with this . Let's do a trial drive. It's cool! It feels like Bruce Willis of Armageddon is shaving the bedrock! Yes, then I will peel off the tape. It is okay to remove the tape . Now, I would like to make a hole with a hole saw. The diameter of the hole at the end also with 6 points Let's open this hole diameter better is it's balanced manner good of was good be may not do Somehow this hole who drilled a hole in the thin drill to it earlier you go that's 15mm beneath you after all is more of 6 mm takes Bali I rasp has come out pretty burrs because pushed by ne drill There is still a good balance! File it. Make it smooth so as not to get injured. There is a burr that seems to pop out, so push it in and crush it and push it to the other side . In This completes the time being, the next I want to decide from the measure the width of flour sifter to the I hollowing out the does what about hollowing out the size of the lid in the first oil pot, which will be the last step you can If you can do this exactly as it is, I think it's okay if you can refer to this measurement result! 86 86.1 85.9 It seems that this is not the correct circle for a moment . I think it is about 86. So let's set the width to 86 and guess! Let's check it again It's half of 86, so 43 Now let's just hit the center of this lid and check! After all! It's perfect! It fits this molded circle! Isn't it exactly Cinderella fit! You don't have to draw a circle with magic and cut it, right? I'll drill a hole for the tip of the scissors . I wish I had a circular cutter, but I don't have one, so this time I cut it with a snips. I will! I will cut this patiently. It is definitely better to have a circular cutter! I finally feel like I'm addicted to it ! If this is left as it is, the cut part will be jagged, so I would like to make it as flat as possible. I will push it with the butt of Magic and dent it. It's still a little wavy, but this is fine! Let's put it in a bonfire can. After all, it feels good. Insert a powder sieve into this. It looks good! When assembled, it looks good. You can't see the jagged edges, and the secondary combustion holes are also nice! This stove sucks air from the bottom and burns it with secondary combustion . That's why I use this powder sieve to remove ash! I will use it effectively because it is hollowed out! As you may have noticed, we will use it as a rostrum! This is ok for the wood stove, but I also want to make what I need when cooking. I will use the miso-boiled mackerel cans that I always have at home! Cut this part to make a trivet. The size and diameter of the canned food is 7.5 cm! With one cut, spread it out and fit it in. Thinking carefully, this time it was full of Cinderella fits! I put a skillet on it! I would like to cook like this Additional firewood can be replenished from the gap with the trivet like this Finally, the storage takes the inner lid like this and fits comfortably in this

Channel: くるこや【 kurukoya 】

Views: 91,763

Keywords: 自作, 自作ギア, DIY, ＤＩＹ, solostove, ソロストーブ, キャンプ, デイキャンプ, ストーブ, 自作ストーブ, 二次燃焼, 二次燃焼ストーブ, 薪ストーブ, ネイチャーストーブ, １００均, 100円均一, スリーコイン, ３coins, 3coin, カスタム, アウトドア, アウトドア用品, カトラリー, ロストル, 火起こし器, 火起こし, 焚火, 焚き火, 焚き火缶, 火起こし缶, ストーブ缶, 缶ストーブ, ロケットストーブ, シンデレラフィット, Cinderella, cinderellafit, プチプラ, 新商品

Id: LvHvybCWKIE

Length: 16min 53sec (1013 seconds)

Published: Tue Apr 27 2021