Unboxing - Full SETUP of Bambu Lab P1S 3D Printer - in 4K

hello 3D printer friends hello bamboo lab users I'm sitting here next to the p1s this is the third iteration of the p1p in under a year which is somewhat concerning however it is also somewhat exciting as it brings a lot of things to the table that people kind of wished the p1p had originally mainly an enclosure originally we had the p1p that came with the early bird kit that consisted of the camera the LED light and the auxiliary fan all three of those items required you to install them yourself the light and the fan actually required you to print things to install them but before we do that we have to attach our gigantic Park cooling fan to our gigantic 3D printed part then bamboo wisened up and smartly released a revision of the p1p that came with the camera the LED but no auxiliary fan the auxiliary fan was optional however the camera and the LED were installed by bamboo themself you will see the new p1p LED light bar is pre-installed this was a great move on the part of bamboo and made the p1p setup a much easier faster and smoother process now just a few short months later we have a new p1p the p1s the p1s comes with the led the camera and this time the auxiliary fan on top of other upgrades as well as a full enclosure obviously all these other little upgrades such as fans camera light auxiliary fan cable chain Etc are nice but the selling point will be the enclosure let's go ahead and pop it out of the box set it up and find out what this new toy is all about as typical of bamboo lab p1p series printers the box is really Hefty and kindly marked with big bright red fragile glass signs to keep your delivery guys from playing football with it hopefully the cardboard itself is thick and strong however mine does have a dent in it on the sides there are also handles so that people carrying your box can grab it pick it up and put it down properly hopefully another small but important detail is the tape not all packing tape is created equally and sometimes you'll get boxes where the tape is ripped peeling off and things like that are happening the bamboo lab tape is strong and not one single section of it as given way at all keeping this box sealed the way the manufacturer intended it I'm cutting the tape with the Westcott carbo titanium scissors the blades on this thing will take your fingers off when you unfold the flaps on the box you'll be greeted with a QR code that says scan to watch the unboxing tutorial you won't need to do this since you're doing it right now with me however to utilize a QR code you simply hold your camera to this code and a link will appear on the screen you touch that link to open the link destination Inside the Box you will notice Bamboo's exceptional packaging some of you give me crap for having a problem with the way bamboo packs their accessories however they pack their printers at a very high level and I'm very pleased with this we're gonna remove that piece of bubble we're gonna remove these top pieces of foam and we are going to Simply peel away these two foams of packing bag those of you who have watched the bamboo ads on the internet they show them grabbing the printer and it's picking it up out of the bag and dropping it on the table we're going to go ahead and do that I'm grabbing the two flaps from the bag with the p1s inside lifting straight up success getting the p1s out of this bag could be a little bit of a challenge but you can handle it simply rip open the top and fold it back down and lift the printer up from on top of the bag push in the bag aside [Music] all right if you are a seasoned bamboo lab p1p user you are in for a pleasant surprise with the new appearance of the p1s as you will immediately be greeted by its beautiful enclosure and it's glass top in its glass front door let's freedom of those coverings I am starting with the door simply removing the tape you'll notice a small flap on the inner portion of the door this plastic protection is basically a bag or an envelope that's sealed in the same way a bubble envelope would be with it open you can now back this bag out and there you have it the p1p magnetic door here on the top you're going to run into the same situation we are again going to remove the tape and we are gently going to lift cover up be careful because it will come off again this is basically a plastic bag so you're going to separate the adhesive or just caveman it and rip it open and then slide the bag off the cover placing the cover back on and making sure it's actually in one piece mine sure is let's go ahead and remove the cover placing it somewhere safe so we can start unpacking and setting up our new toy I'm going to go ahead and start removing all the tape here's a piece of tape over your micro SD card be careful with the card I noticed my card is actually loose so go ahead and click it out and then click it back in take your foam off take your foam off take your box of Parts out here you can see the new p1s cable chain assembly pre-installed included with the p1s reaching inside your machine either with the front door or from the top you can grab this foam right here gently slide it upward [Music] and remove it it may catch on the bed please be careful here's some super dry you might want to save this remove the other side and you now have a clear visual on one of the other major upgrades of the p1s which is their new golden Pei bed bamboo has in fact told me that this bed has significant performance improvements over the original p1p bed behind this bed you're going to see two pieces of foam and under the bed you are going to see two pieces of foam just like the p1p we are going to leave those in place until we turn the printer on at which point the bed will rise and we will remove that foam for now we'll focus our attention right here to the hot end and we are going to free it from its zip ties and cardboard covering just reach in clip the zip tie behind it is this little red thing this is a warning that you have a belt right next to this zip tie and there is a possibility of clipping the belt while removing the zip tie don't do that make sure you are on only the zip tie and clip the zip tie gently remove the zip tie both zip ties are off now we are going to free the hot end from the cardboard and we are going to take our sweet time doing it I like to rip the cardboard so that it opens up like this and then you pull it up and then be careful because of the new cable chain being in the way we're just going to work that cardboard through the cable chain and toss it away freeing up and exposing for the first time our beautiful bamboo lab hot end cover you will see the hot end cover has some green tape so we're just going to go ahead and peel that green tape off now for the first time we can look at some of those included upgrades the golden Pei bed the pre-installed auxiliary fan the pre-installed camera and the pre-installed LED light bar those of you with Keen eyes will notice that the auxiliary fan no longer uses the large stand that the previous p1p had us print and install underneath it the new fan is now mounted to the enclosure door of the printer itself before we get carried away don't forget right here in The Poop Shoot is a piece of foam just get your finger in there just give it a slight little pull and now your poop shoot and nozzle cleaner are good to go shift your eyes over to the right and grab that piece of tape right there too for now we can put the cover back on or leave it off speaking of the cover p1p owners will notice not the power cable and Bowden tube no longer protrude over the case and interfere with covers it now comes through from inside the printer through this little connection right here some p1p owners were actually 3D printing their own and doing this modification it's now part of the printer itself now we have our traditional box of toys so let's pop it open again the box is sealed with industrial strength tape so you're going to have to cut that open strong army or using your fingernail probably isn't going to cut it [Music] a tiny little spool of green pla basic very disappointing the same pathetic screen from the p1p the same spool holder as the p1p the power cord a piece of boating tube a nozzle declogger and a small mystery box inside the small mystery box is a little Allen key an extra 0.4 nozzle extruder screws double-sided tape for the phone holder that is included on the memory card spool holder screws hot end clip and screws nozzle cleaners razor blade and double-sided tape for the scraper also included on the memory card another Allen key thermal grease for the spare hot end and wow one two three four five packs of lubricant grease what does bamboo lab know about this new p1s that we don't hmm the p1s no longer comes with the new Green Bamboo 3D printer adhesive I still can't help but feel this is the acknowledgment that there was in fact adhesion issues with the original print bed and those issues have been resolved with the new golden Pei bed hiding inside your p1s all the way in the back is one additional Bell for you to discover filtering the air through these slots right here is your fancy new refillable carbon filter foreign to install these toys and prepare the printer for testing first thing we're going to do is install the screen the screen comes taped in a little bag just slide it out and there's a protective film on it you can keep this film on it for a little bit if you'd like or just peel it off right now there's a clip right here and there's a clip inside it only fits one way match it up and clip it into place I like to use my fingernail and just push on the plastic to lock it in I don't think anything has changed but I do feel like that was easier to connect than my p1p screens were but then again that could be all in my head with the screen like this we're going to guide this wire into the orifice of the screen itself line up these notches with the slots and simply push left congratulations your p1p now has a screen now we're going to pop this door open and we are going to unlock the print bed and we are going to find three screws indicated by those little red arrows and unscrew them simply put the Allen key on the screw and turn it counterclockwise there's another one in the back right there it's tough to reach get your Allen key on that and unscrew it there's one more on the other side again indicated by the red arrow get your Allen key on it and remove it swing your printer around and look for this section right here clearly marked spool holder assembly holes oddly enough one of those holes is occupied we are going to remove it with our Allen key [Music] with that removed look for the bag that says four spool holder and take those two screws out take a wild guess what they're for this bull holder goes like this if you're not sure it actually says top right there on the spool holder I find your easiest way to do this is to pass your Allen key with the screw on it through the holder and hold it in place again start that first screw now with that first screw firm enough to hold it in place I'm going to put the second screw on the Allen key and pass it through the same way and secure that one too you now have a spool holder on the back of your p1p now with your shiny new p1s fully assembled it's time to load the filament bind it to the handy app and run our first test print please do notice the initial patching foam under the bed is still in place plug your p1p in and install your filament unlike many other printer models you will not have to switch your power to 110 it will already be set for you you simply plug the printer in and that's it to load up your filament we're going to swing the printer around and grab the sample it came with looking for it and peeling off the tape holding the filament end in place when dealing with filaments you never want to let go of this end because it can spring back cross underneath itself and create a loop and that Loop will create a jam if you can get this tape off super if not simply clip it with your snippers have a look at your filament spool holder your filament spool simply goes over it and it rests like this what's the filament coming over this way we are going to take the filament guided into the Bowden tube and simply push it until it stops those of you who own p1ps will notice they have simplified this process there's no longer a coupler here this is a much leaner setup than the original p1p setup at the filament spool and here you can see our fancy green filament has entered the printer traveled through the modem tube and entered the direct drive of our fancy p1s hot end if you do not have the bamboo handy app installed on your device now is the time to do it install that handy app on your phone and turn your printer on bamboo would like that before use you please make sure you have read the user manual carefully we're going to say okay we are going to say okay we are going to tell it where we are I am in North America and if you do not have the bamboo handy app on your phone already simply open your camera and point it to that QR code and it will take you to download the bamboo handy app now we are simply going to open our phone camera and point it at the QR code a link will open and we're going to touch that link that will take you to the download for the bamboo handy app if you already have the app you can simply wait a moment and it will open the app for you you then check the two boxes and choose confirm to bind the screen is asking me to pair I'm going to press ok to pair now I wait for the app to finish the app will then prompt me for Wi-Fi this is the Wi-Fi I will use with the printer you'll be using 2G Wi-Fi type in your password and press bind you will notice your machine went back to the opening screen don't be concerned that's perfectly fine please confirm you have removed the three screws with the Allen key we have done that finally let's run the self-test routine to check the status of your printer I'm going to press start please note the foam is still in your printer and your app will download a G-Code file and start to do its thing if you'd like you can open the door and you can check it out the official instructions say to leave the foam until the testing is done however I like to go ahead and remove the foam gently right now if you'd like you can close the door or you can leave the door open [Music] thank you your self-test is complete your printer is ready enjoy printing something tells me this printer is going to have a firmware update I'm going to press finish you can either wait for this firmware update to appear or you can scroll down new firmware is available do you want to update now it's as if I can predict the future we are going to say ok to update we are going to say okay to update again OTA means over the air so it's going to download and then install the firmware update for you thank you the firmware was successfully updated confirm and now you will see your firmware represents the new number you can simply press the back button and back out and then return to your home screen where you'll notice it says ready to print and there it is the bamboo lab p1s the new enclosure makes it an absolute thing of beauty whereas the p1p kind of looked like a skeleton of a printer with its beautiful glass front door and its lovely glass top lid the p1p has transformed from the low budget ugly duckling of the bamboo lineup to a complete and beautiful package that will stand out and finally look the part in your Workshop during printing your p1p will automatically create a time lapse that time lapse video is stored on this micro SD card to remove it push it down and release then remove the card place this card into a card reader on your computer where you will find the video and time lapse of your prints I'd like to talk to you about memory cards memory cards are very important for the correct function of your 3D printers even on the web and app controlled bamboo lab p1p the micro SD card is extremely important as it is required for the printer to work it also is required to record your video and beloved time lapse content we are not going to trust this content on a cheap unbranded Chinese memory card I am going to suggest replacing it immediately with a quality card of 32 gigabytes I use this card right here this is a SanDisk u3 high endurance micro USB card the high endurance cards are meant to endure impact extreme temperature and constant read and write usage amazingly in today's world this incredible card costs about eight dollars please when buying on Amazon watch who you are buying from I will leave a link to this exact legitimate card in my description to replace the card simply take your finger and depress the memory card and then release the card will push forward you can then pinch and remove it install the new card pins forward by gently aligning it to the memory card slot then using your finger to depress it until you hear the click it will lock into place considering the price difference at the time of recording is one hundred dollars getting the p1s over the p1p is an absolute no-brainer I do have concerns that the p1p was upgraded this drastically inside of one year however it does show that while some people dismiss specific competitors such as creality and their enclosed K1 series bamboo lab clearly does not and is taking competition very seriously having swiftly upgraded the p1p to match features of the K1 series and likely features of other upcoming competitors and more specifically adding things that p1p owners wanted it is very nice to see inside of a year the p1p go from a bare bones skeleton of a machine with accessories you needed to install yourself evolving into a machine with those accessories included installed by the manufacturer and then the entire printer reiterated into a fully enclosed unit with those accessories ready to roll day one in your print shop you are on the 3D rundown YouTube channel I'm Greg Adventure your instructor on 3D rundown.com and unboxing setting up this beautiful bamboo lab p1s printer was today's adventure [Music]

Channel: 3D Rundown

Views: 22,261

Keywords: bambu lab p1s, bambu lab p1s 3d printer, bambu lab p1s vs x1 carbon, bambu lab p1s 3d printer review, bambu lab p1s setup, bambu lab p1s price, bambulab p1s print, bambu lab p1s test, bambu lab, bambu lab p1p 3d printer, bambu labs p1s, bambulab ams, bambu lab p1p vs x1 carbon, bambu lab p1p 3d printer review, P1S Unboxing, bambu p1s unboxing, bambu p1s, p1p vs p1s, bambu lab p1p, bambu p1p, bambu lab 3d printer, bambu lab p1 series, p1p build, p1 series, p1p bambu lab

Id: F8azd8XbTI4

Length: 25min 26sec (1526 seconds)

Published: Wed Jul 26 2023

Reddit Comments

[u/Atomic_RPM]

Appreciate the video!! Thank you!

[u/Toolman111]

Hey Greg, not to watch a video. Thank you for your time and sending these. I’ll have my P1S on Friday. I’m trying to direct messaged you, i’m not sure how to do it. I keep trying that your name won’t come up so if you got any suggestions I would appreciate it. I wanna send you a couple things. Thanks again for your time sir.

[u/Toolman111]

Thanks Greg for your time. I want to let everybody know they better grab up the New Bambu Lab ASA before it is gone, I I would say it’s gonna go very fast, Bambu Lab is sure getting a lot of my money. I gotta do something and start making some back, lol. 🤣🎚🇺🇸

[u/Toolman111]

I was trying to find that link you sent me and I can’t find it anywhere. Resend the link if you don’t mind whenever you get time.