The EASIEST Beam Installation We've EVER DONE!

Video Statistics and Information

Video
Captions Word Cloud
Reddit Comments
Captions
hey gang welcome back to the channel i'm paul with studpack in our previous video you saw that we built this temporary wall to support our ceiling and part of our roof because we had to remove the original load-bearing wall in preparation for our new beams which we are still waiting on now remember that oven we put out by the street and jordan said the oven will be gone before the beams are here well that's true we are still waiting on the beams today's tuesday they promised me tomorrow wednesday six days after i ordered them and you'll notice on this wall right here i put the studs under the joist that's how i do it and that's really how it should be done they're doing good except for this little guy right here this treated one it's got quite a bow in it today but don't worry little buddy as soon as we get that beam in here we're going to take the load off of you now speaking of cost a lot of you are asking about the cost of our structural engineer and how did i find him so they have a flat fee of 500 and that includes a site visit and their drawing that we submit to the city along with our permit i found my guy through my brother-in-law so i kind of got lucky i had an end but i actually did a search on my phone for structural engineer and in our city of about 350 000 the company that we actually use came up second in that search so it shouldn't be too hard to find if you're in a smaller town i would probably go to the permanent office and ask them who they recommend so remember when i said that we had the original drawings to this house and that satisfied our engineer well what if you don't have drawings to your house what are you gonna do well let me show you in our previous video i mentioned a 12 inch long bit that i had i don't know anywhere where that's 12 inches so i went home and actually got the bit and here it is it's three quarter inch 24 inches long and i bought this years ago to determine the depth of a footing on a job i was doing in southern california just for the engineer so this slab we're standing on should be about four inches thick i've got a piece of tape here what do you say we give her a whirl and see how thick this slab is jordan do it all right all right i'm about halfway and i'll be able to hear it and feel it in the drill when it goes through the slab there we go there we go perfect right at four inches now let's go over here and show you how we find a footing so let's say you're in the designing phase of your project and you need to know how thick your slab is right there for that new post that new wall that new beam you're not sure there's a footing there this is how you do it you can remove a piece of baseboard and drill right here or you can pull back a corner of the carpet and there's plenty of room to drill between the tackles and the wall let's give it a go right here and see how deep this footing is i'm just going to go right there [Music] so this three quarter inch hole that deep is about at the limits of this drill i hit a piece of rebar i can tell by what the bit is doing but you get the idea i could simply move this to a new location to satisfy the engineer they make bits that cut through rebar but you see what we're trying to talk about to establish the depth of your footing so we're going to leave that there and let me show you today's project if you look way up there you see a two by four that is nailed to the bottom of the roof rafters and the roof rafters are 24 inches on center they're two by sixes and then we have these braces coming down from that 2x4 to the top of this load-bearing wall now those braces have to go because they're in the way of our new beam so this morning i use my dot laser you've seen us use it before to get this 2x4 directly under the one that's attached to the bottom of the roof rafters the roof rafters are two by sixes 24 inches on center so we're going to build a temporary wall from this 2x4 on the slab to that by four on the bottom of the roof once we do that we can remove these braces that are now taking the roof load to our load-bearing wall that has to come out now i bought 16 foot two by fours to go from here all the way to the roof and you may be wondering why aren't we supporting the ceiling well remember this ceiling is at eight foot and it comes down because we're reframing it at nine foot now i could take the ceiling down first but then i would need a really tall step ladder so i could stand on the top step of that one to reach way up there but since i had this ceiling here i can use it as a walkway to put in our wall i'll be up there with a nail gun jordan's going to be cutting the lumber outside bringing it in we'll build this wall and then we can take this ceiling down so that 2x4 up there is at an angle and i need to support it properly so why don't we take a walk outside and i'll show you how we're going to do that well we're outside at our dumpster and let's let this 2x4 that i've got on this step right here represent that two by four that's on the bottom of our roof rafters and so right now we have another two by four like that that's going down to the top of our load-bearing wall that has to come out and it's also in the way of our beam so this brace has to go out but before i can pull the brace out i need to support the roof so i jumped up in the attic and i held this under there plumb because i'm trying to match this angle i held this up there plumb i just used my torpedo level as a guide and i drew a line and that's my angle now let's go over here and i'll show you the next step i just use my speed square to make a corresponding 90 degree line this goes away and that forms a bird's mouth just like that so this was my template that i used to mark the ends of these six 16 foot two by fours i've already got these four cut i mean i made the initial cuts with my circular saw just like you see here and i'm going to finish them with the jigsaw so why don't we finish those two real fast and get that done there we go those six are all ready to go now you may be wondering what is this cut you made right there well remember i'm going to be in the attic and jordan's got to come down here and measure these all by himself and cut them and bring them to me so that little kerf is going to be a spot for him to hook that tape measure and pull his number from here pretty cool huh what do you say jordan you ready to put these in yep let's do it all right i'll get tooled up and head in the attic my favorite spot at least it's chilly today that's true all right let's go [Applause] [Music] [Applause] so [Music] [Music] so [Music] [Music] [Music] [Music] [Music] [Applause] [Applause] [Applause] [Music] alrighty gang that was a huge step for us today since we didn't get the beams we regrouped and we built this 16-foot wall that's supporting our roof check this out that hurts i don't think the gronk could even get through that so remember that thing is 16 feet tall we made these an eighth long so it kind of sprung the roof up and transferred the roof load to these we even repurposed some of our ceiling joists that's horizontal bracing we've got one diagonal brace and two braces back to the structure so it's supported this way and this way you also saw in the time lapse where we took down our original diagonal bracing for the roof and our ceiling joist all that stuff is outside all i got to do is sweep up and vacuum and we're ready for tomorrow i went by the lumber yard this morning to check on my beams they said they'd be here tomorrow but then they called me later and said hey look stud pack we're watching your videos unless you get 1500 likes we're not going to deliver so please guys get down there and smash that like button for us so we have some work to do tomorrow we'd really appreciate it fingers crossed for that delivery we'll see how you guys do and we'll see you tomorrow all right gang today is beam installation day we're going to put this little one up hopefully those guys deliver it keep smashing that like button but while we're waiting let's talk about these two king studs right here the plans call for king studs on the end of the beam nailed together so we use two 10-footers we just kept them long like we told you about i'm going to talk about how these are nailed together when we do the other side but what i did first i used my dot laser and remember we showed you when we cut the top plate i projected that line down to my bottom plate and i cut this spacer to ensure that these were perfectly plumb just nailed that to the bottom plate with two nails and then attached our king studs at the bottom and right here at the top so let's go over there and get that other one then we can cut our beams to length when they show up [Music] right here [Music] all right gang both kings are in you saw me put a six inch structural screw through the kings into the original top plates that wasn't called for it's just something i did for my own peace of mind just to tie our new structure into the original structure every little bolt every little screw is going to help tie all this together got a lot of weight we're dealing with right here and so speaking of weight let's talk about how these are nailed together so the plans call for the two kings and the three studs under the beam to be nailed together to uh acquire what's it called composite the plans call for the two kings and the three studs under the beam to be nailed together for composite action what that means is they're fastened together in a way that they act as one member so that when you put a vertical load on the top one of the members doesn't buckle out the load is on all three members equally and they act as one unit so on the kings what we did the nails are eight inches apart staggered so this is eight this is eight and obviously 16 along each side and about an inch from the edge and then we we nailed all these and then we flipped it over and we did the same thing so i've got a nail here and i've got a nail here got a nail here one way and a nail here the other way all the way up on both sides and the studs under the beam will get the same thing so hopefully those beams are going to show up in fact i think i hear a truck you want to go check it out see if that's our boy let's see if our gold is here all right let's go check it out all right y'all came through for us check it out there's our beams we appreciate you smashing that like button for us not only did we get our gold delivered we got some silver too look at that that's our custom-made hanger to attach the two beams about 80 bucks from simpson and we waited what six days for all this stuff pretty crazy these days how long you gotta wait faster yep now these are pretty tall i mean they're 16 inches tall look at that i think the other ones we've done have been 12. right so why don't we take this banding off go inside and take our measurement cut these and start getting them installed [Music] so [Music] so [Music] so [Music] [Music] all righty gang come on down here we got our beam assembled according to specs we pop the line three inches from the top and bottom edge specs one of the screws three inches from the top and bottom edge these are the screws we used quarter by three and a half inch structural screws the specs also wanted them 16 inches apart which is what we have here aligned with our studs that are 16 inches apart and then staggered so the bottom row is staggered eight inches from the top row just like that and whenever we're assembling a beam we're always mindful of where our joist hangers are going to go because you don't want this to happen you don't want a joist hanger over a screw that's the worst is when the nail is at the screw location so we planned all that out and then if you come on down here to my left you'll see we even planned it out for the big guy and we're fine we got a screw here one here that one gets covered and then if you see right here what you're seeing is a splice in the top lamination of the beam obviously this this can't be one sheet so they're spliced together and then the splices i think are minimum of eight inches apart for maximum strength so now that this is built we want to get our stud packs built so that when we lift this beam in the air we can slide that stud pack under them and set the beam down so let's hop outside and build those stud packs [Music] all right guys both side packs are ready we got one right here the other one's on the other end and they are nailed together just like the kings were to give us that composite action so that this guy is acting as one solid post and it is solid and if you saw from the time lapse we nailed them all together first and then cut the whole thing to length so our bottom and our top perfectly flush so now it's time to lift this beam did you eat your wheaties this morning bud i did because i was gonna have you hold it up for me while i put the stud packs in okay you ready you've seen this in the past lift heavy stuff and we could lift that if we wanted to it's not that heavy but we have a lot going on up here that thing is a tight fit in this stud in this beam cavity we have all these wires in the way we have this wall in the way this brace in the way so i'm going to get in the attic and rig up a hoist and we're going to lift this thing into place safely so what do you say jordan we switch from our carpenter's hats to our riggers hats let's do it all right let's get it done all right gang i've got a cable hoist that i bought to lift the piano so we're going to get more use out of it today and we're going to simply hang it from this rafter to lift that beam we have our dot laser set up at the midpoint of the span that way i'm lifting directly at the center and the first thing i'm going to do is drill a hole through this rafter [Applause] all right i've got this 5 8 inch bolt with more washers than i need but that's all right i'm going to put it through that hole this is going to be tricky man all right i'm gonna hook this over the bolt just so i'm not having to reach so high in the air and the washers are trapped in that so it's not going to be right exactly something just went in my ear all right now this rafter that we're lifting from is being supported here and here and there off the main roof so i'm really comfortable that it's strong enough to lift that beam what do you think that is jordan less than 200 pounds right around 200 oh yeah i think it's probably heavier than georgia okay and here's our hoist like it on there there we go all right let's see if it'll reach bud all right okay all right gang there's our setup we're ready to go i'm strapped off to the rafter up here i can crank comfortably right here and jordan's going to show you the bottom you ready here we go oh easy is it pretty balanced nothing's creaking always a good sign what was that [Music] [Music] [Applause] all right gang so i'm about all the way i can lift right now we knew that was going to happen that's why we use this strap so jordan's going to screw a block to each king stud i'm going to lower the beam onto those blocks remove this strap and hook directly to our chain then we can lift it the rest of the way okay okay all right all still good uh this guy is gonna just give us grief i can i can disconnect it you're gonna put a screw in it let me push it as much as i can all right perfect good thinking yep okay look at that is that it yep are we in yep sweet all right i'm gonna hop down and we'll put in our stud packs and then lower it back down all right coming down [Applause] all right all righty gang stud packs are in woo hoo now you notice we put in some six inch structural screws just to tie the stud pack to the kings just to join it all together and if you're wondering this is actually where our name came from if you go back and look at the fourth video we ever made we put up a beam similar to this but different in a lot of ways our family had decided on a couple of names for the channel i knew jordan didn't like either one of them so all day long we were installing stud packs and then we had to move a stud pack and at the end of the day jordan says dad i love that name sled pack and i said go for it let's do it and the rest is history so these are in all that's left is to put in the 10 joist hangers there are seven singles and four doubles and then we can remove this wall so we're gonna install the joist hangers with this palm nailer we'll be sure to put a link in the description below these things are awesome for these confined spaces they're a little loud so you gotta wear hearing protection and then if you come over here we have our bottle jack ready and we cut a stud because some of these are going to be lifted up so we're all flush on the bottom so what do you say bud you ready to finish this thing let's do it let's do it [Music] [Applause] [Music] foreign [Applause] [Music] [Music] [Music] yes did it good job [Music] alrighty guys that beam is up went just as we planned it really no hiccups at all no problems you know i think about something like that a lot and then when it all comes together it is such a good feeling the worst part of the whole thing was waiting for the beams you did see me use that palm nailer i had 80 nails to drive 10 hangers 8 nails a piece i know they make that positive placement tool where you put the tip in there and it fires the nail i just don't do this enough to warrant owning one of those so the palm nailer is a great option the other thing if you saw us under the beam we always made sure we had a block here as a secondary backup in case the come along failed so that was great and this was really a great run through for this one this one's going to be like seven feet longer and about a hundred pounds heavier than this one and look gang we don't have anywhere to lift it from i can't get up that high to that roof and i don't know that it was supported anyway so leave us a comment and let's let us know how you would raise that beam uh i know they make a genie hoist or a duct hoist as i call it and you crank it up it's like a forklift like that that may be our best option but i sure like the way that that hoist gave us total control and we could move it any way we wanted to and this beam has a lot more challenges than this one one end's going to sit in a bracket on the beam we just put in the other end's going to be on a stud pack we have this cathedral ceiling on one side and the dining room ceiling yet to be framed on the other side and we also have to account for the foyer ceiling which is already there so make sure you stay tuned for that video if you like this video be sure to smash that like button for us we'd really appreciate it leave us a comment down below and subscribe if you haven't already and we'll see you on the next you
Info
Channel: Stud Pack
Views: 33,039
Rating: 4.9884577 out of 5
Keywords: studpack, stud pack, construction, diy, home remodel, home renovation, beam installation, versa lam, how to install a beam, open floor plan, dreamhome, dream kitchen, open concept, cable hoist, how to support roof load, how to build a temporary wall, how to build a wall, jack stud, king stud, structural engineer, palm nailer, joist hanger
Id: Vnzj870d_jA
Channel Id: undefined
Length: 26min 26sec (1586 seconds)
Published: Thu Mar 04 2021
Related Videos
Note
Please note that this website is currently a work in progress! Lots of interesting data and statistics to come.