Rockwood Pop Up Camper - Instructional Video

for over 25 years Rockwood has grown to become a name synonymous with camping and the great outdoors let's see how easy it is to set up a new Rockwood camping trailer setup begins with cranking the dolly jack to level the camper next release the four latches that hold the roof secured remove the lifter crank handle from its storage area and slide it in the crank shaft when the handle is securely in place turn it clockwise to raise the roof the rock wood lifter system has an automatic break if the handle is released at any time cranking up or down the roof will hold its position the guide wire will tell you when the roof is extended to full height you can see rock wood uses wider lifter posts these posts are twice the size of many competitors and will add more support and stability to the roof set the safety supports on the opposing corner liquor arms setting the stabilizer jacks is an easy operation for any member of the family be sure the jacks will rest on a solid surface such as hard-packed soil or boards this simple procedure distributes the campers weight among the four stabilizers make sure the roof is in the up position prior to setting the jacks this will assure proper leveling in the premiere models a crank down jack with sand pads as a standard feature simply crank down the jacks to stabilize the trailer after all stabilizers are set slide the bunk end out until it is fully extended remove the bunk supports from under the mattress the support poles fit easily into the frame and attach to the buck locking it into position notice the bed ends are made of plywood and not particle board rock would permanently attaches their tent material to the bunk end to ensure dry bedding during setup and takedown in the event of rain it also provides extra safety if someone were to lean against it from the inside adjust the side bunk tent assembly and secure the corner with the velcro fastener velcro fastens the tent to the length of the bunk notice the storm flaps Rockwood uses on the tent material this feature allows water to run off the tent as opposed to collecting on the extrusion or rolling around onto the wood of the bed ends a shock cord is also added for safety next velcro the lifter post cover in place for added protection against the elements and insects now repeat the bunk and setup procedure on the other bunk end rain or shine you'll feel secure knowing that rock wood uses the strongest most water-resistant tent in the industry vinyl on is a 5-piece sectionalized tent with down facing interlocked seams and double stitched at all tension points see your owners manual for more information on how easy it is to clean and maintain your tent for years and years of a the remaining setup procedures are done from inside the camper set the galley into position by flipping it up onto the cabinet on the premier models simply grab the handles on top of the galley and lift into place next zip the tent corners the five piece tent assembly makes it easy to repair or replace a panel should the need ever arise remove the dinette cushions and place the table to the side or on the bed remove the stove from its storage position and put it in its place on the galley next position the seat cushions and supported back cushions on the bases in many models Rockwood uses a free-standing table so it can be utilized both inside and outside the camper simply unfold the table legs and lock into place rock wood uses the fantastic vent in all series except the Limited's this 12-volt 3-speed fan is quiet dissipates condensation and exchanges the air in your tent camper allowing you to breathe natural ambient outside air setting the screen door on a rock wood is a snap release the door by turning the to twist locks as the door swings down lift it up and align the tabs into the slots on top of the sidewall twist the retainers to hold the top of the door secure attach the two door sections together and release the retainer clip on the side of the door now simply attach the tent to the screen door with the velcro strips next put the overhead support pole into the bed bow and push into place notice that all supports are powder-coated and won't leave unsightly marks on the interior tenting now adjust the length of the pole until the bunk material is stretched tight zip the last two corners of the tent set the other bunk and pole into place and you're ready to go camping Rockwood also offers tent campers with EZ glide slide-out dinettes there are a few additional steps you'll need to do release the slide room by unscrewing the threaded locks take hold of the handle and pull out the slide room attach the cotter pins to the steel pins extruding from the sidewall at the seal similar to the bed ends Rockwood attaches the tent material to the slider so simply attach the velcro strips to both sides of the slide out from the inside attach the rafter Pole to the tent bow and stretch the tent into position insert the end of the rafter pole in the metal clip and adjust the tension assemble the dinette seats and your Rockwood tent camper is ready to use rock wood has combined Amish craftsmanship at over 25 years of experience to build you a camper of exceptional quality and value thank you for choosing rock wood

Channel: JD Berry Trick shot

Views: 48,040

Rating: 4.7192984 out of 5

Keywords:

Id: HyTu6mkOlBA

Length: 6min 37sec (397 seconds)

Published: Thu Nov 07 2013