Inter VLAN Routing using Layer 3 switch | CISCO Certification

hi friends welcome to all in this video we are going to see how to configure inter VLAN routing using a layer 3 switch here we are going to use a 3 layer switch 3 5 6 0 also 2 switches to + 6 0 the number of PCs right we will rename these devices this is multi research it will give us M us you CC s1 this is s2 also we have a number of PC so PC 0 pc-1 pc2 then a pc 3 pc 4 and PC fine now we will connect to these devices coming to connections copper spray through here we will use the FA 0 / 1 - FA 0 / 1 this is for one VLAN and again we will connect F s euro / - 2f s 0/24 this is for the second villain here FA 0 stars - to this PC 0 FS 0 / 3 to this PC 1 then FS Rosen's 23 to this PC - so here this pc 0 pc 1 will be in one VLAN then a pc 2 will be in another villain now we will connect two years to FA 0 / 3 - FA 0 / 1 then FS 0 / 4 - f a0 / 24 then we will connect these pieces from s to F a0 starts - to PC 3 FS 0 / 3 to pc 4 then FS Roslin's 23 to pc 5 here we are going to use a two vielen vielen ten and a VLAN 20 we will highlight those VLANs a VLAN 10 and VLAN 20 so these two pieces p c0 and pc one in VLAN 10 also this pc true and pc 4 also in a VLAN 10 here is VLAN 10 and these two pcs pc 2 and pc 5 will be in VLAN 20 this is for VLAN 20 this is her VLAN 10 here we will use the network across as 192.168.1.0 / 24 and this is sephora VLAN 20 here we will use the network at rest as 192.168.1 2.0 / 24 no I would like to label all the ports are used in these switches so here we can see the port FA 0 / 1 only some multi-layer switch and on s 1 FS 0 / 1 so we will label that if 0 / 1 here also F 0 / 1 and here we can see F 0 starts - and on s 1 FS 0/24 you see so FA 0 / 2 this is the first Earth or net 0/24 also here we can see at the port FA 0 sonars 2 which is going to which is connected to PC 0 or so here we can see FS 0 / 3 which is connected to PC 1 we will label that also you have 4 0 stars - and this is AF 0 / 3 or so here we can see the port fase Roslin's 23 which is connected to pc 2 0 / 23 coming to the link between the multi-layer suchan the s2 here we can see the port FS 0 / 3 and to the other side the FS 0 / 1 FS 0 / 3 this is f 0 / 1 and here we can see the F 0 / 4 and the FS 0/24 into this IDs AF 0/24 also coming to the PC so here we can see the port FS 0 / 3 and here we can see this is oh this is FS Rosner's - and this is FS Roslin's 3 we can verify that once more here we can see FA 0 stars 3 which is connected to PC 4 and this is FS 0 / 2 which is connected to PC 3 here we can see the port the FA 0 / turn D 3 which is connected to PC v c yv labeled all these ports because we have to assign the correct port - it's our respective VLAN correctly coming to a topology here we can see the link between this multi-layer switch and the s1 as well as this s2 we can see two links why we given these two links obviously one link is for this avail and 10 and the other one is for a VLAN 20 the same way we can see the links between multi-layer switch and this s 2 know what we will do we will highlight the needed VLANs for these links here we are using this color right so this is for real and 20 here we will use this link for VLAN 20 so I would like to highlight this link and coming to this side here we will use this link will highlight with this color alright so we'll choose the color for the VLAN 10 and here we will use this link for VLAN 10 also here we will use this link for VLAN 10 right now if you observe this topology very easily we can identify the ports which would be as a into its respective VLAN if we consider this uchi s1 here we can see the port fs0 slams 23 and Shiraz last 24 we will assign to VLAN 20 or so here we can see FS 0 / 1 0 / 2 and 0 / 3 we will assign to VLAN 10 coming to the switches to here we can see the port FA 0 / 23 and 24 we will assign to VLAN 20 or so we can see the port FA 0 / 1 0 / 2 and 0 / 3 we will assign to VLAN 10 also coming to our multi-layer switch here we can see the ports if is 0 / 2 and the FA 0 / 4 we have to assign to VLAN 20 or so here we can see the faster parent 0 / 1 & 0 / 3 will be assigned to VLAN 10 coming to the configuration first of all we will configure all these pcs we will configure at this VLAN 10 pcs pcs your OPC 1 pc 4 and PC 3 coming to PC 0 and here we can see that network actress what be insane for VLAN 10 192.168 or 10 dot 0 / 24 so coming to IP configuration here we will give the IP address 192.168.1.1 and here is the subject to mask and here we will use the default gateway as small will copy this you will use the first usable IP address from this a network over nine two dot one sixty eight dot 10.2 one coming to pc one the Stolp IP configuration and here is the address what we are going to use for this PC you'll use the next Tetris at 10.11 then the default gateway then coming to PC 3 desktop IP configuration shall we use a tender toe default the gateway coming to PC for desktop IP configuration here is the IP address then the default gateway now we will configure these pcs PC to and PC 5 which is in VLAN 20 and here we can see the network actress we are saying for a VLAN 20 192.168.1.0 / 24 coming to PC to the store by the configuration and here we will use xx dot 10 and we will copy this actress here is the subnet mask and the default gateway here we can see 20 row 2 1 coming to PC 5 desktop IP configuration here is the IP address xx dot 11 to mask and the default gateway now we will verify the connectivity here we can see the VLAN 10 all the devices will be communicating each other we can see pc 0 pc-1 pc2 and pc 4 I will communicate to each other also PC 2 and PC 5 will communicate to each other so we will verify that this is 0 command prompt here we will let ping to 192.168.1.1 here we can see we are getting the replay now we will ping to toe also will ping to 13 we are getting the replay you will try to ping to a PC 2 which is in VLAN 20 that is so 20 dot 10 Rico's timed out no we are not getting the replay also we will ping from PC to to PC 5 ping to 192.168.1.1 and here we can see we are getting the replay we'll try to ping to PC 0 which is in VLAN 10 so here we have to give a 10.11 will get 10.10 this is the IP address of a pc 0 request timed out no you are not getting the replay here we can see the IP address of each of pcs on its respective VLANs no we will verify the VLANs so by default all the ports are connected to the default of VLAN that is VLAN 1 we can verify that using the show command show VLAN brief and here we can see the details all the ports from FS 0 / 1 tilde 24 or so G 0 / 1 and G 0 starts - they are assigned to VLAN 1 coming to us to show we then briefed and here also we can see the same result now we will come to the configuration first of all we will do it on this with gs1 configure terminal we will set the hostname as yes 1 we will create the VLAN oops VLAN 10 and we will name it us students the creativi line 20 name it as the faculty now we will verify these VLANs chauvelin brief here we can see the details VLAN 10 and the VLAN 20 starers is active now we will assign thoughts to the VLAN here the first 20 ports I mean from FS 0 / 1 till FS or oznas 20 we will assign to VLAN 10 configure terminal interface arrange fasterthan or 0/1 tilton g support mode as access support access avail and 10 in the remaining ports we will assign to a VLAN 20 will exit interface range e faster third 0 / 21 till 24 we will search for the modest access support access a VLAN 20 now we will verify the details show VLAN brief and here we can see the details here we can see the ports FS 0 / 21 till 24 is a same to VLAN 20 name difficulty or so here we can see the ports from FS 0 / 1 till FS Rosner's 20 is assigned to VLAN 10 students and remaining 2 ports at G 0 / 1 + GC rows - is in the default - VLAN coming to topology we can verify at the wheel despot assignments here we can see FS 0 / 1 0 / 2 + 0 / 3 they are in a VLAN 10 and here we can see FS 0 / 23 and the 0/24 they are in VLAN 20 now we will do it on other Suchi as to enable configure terminal hostname as s2 VLAN 10 name as the students VLAN 20 name as a faculty chauvelin brief and here we can see the details we lent 10 and a VLAN 20 now we will assign ports to the VLANs configure terminal interface or a in chief master third 0 / 1 till 20 we will assign to VLAN 10 before that we have to change the mode such reporter mode as access such a port access VLAN 10 now we'll go to interfaces fasterthan at 0 / 21 till 24 so cheap or timorous access such a port access a VLAN 20 now we will verify show VLAN breathe and here we can see the details the ports FS euro / 21 till 24 we assigned to VLAN 20 name difficulty or so we can see the ports FS 0 / 1 till 20 we are saying - VLAN 10 named students and here we can see two ports G 0 / 1 & 0 / 2 is in be a default VLAN topology here we can verify the port assignment to the VLAN here we can see the port FS 0 / 1 0 / 2 + 0 / 3 they are assigned to VLAN 10 and here we can see the port FS 0 / 23 and 0/24 are assigned to VLAN 20 now we will come to our multi-layer switch here we can see the ports FS 0 / 1 and this grows large 3 we have to assign to VLAN 10 and the ports FS 0 starts - and the FS 0 / 4 we have to us a into VLAN 20 coming to our switch enable configure terminal we'll set the hostname as ms we will create the VLANs before that we will let check the VLAN sadhu show will end brief and here we can see the details here we have the default to VLAN and all the ports are assigned to this default to VLAN so we will create two VLAN 10 and we will name it as a students will create VLAN 20 name it as faculty you can verify this a do show VLAN brief and here we can see those billions created 10 and 20 now we will assign the ports to its or respective VLANs configure terminal interface or a into faster third at the 0 / 1 and the faster turn at the 0 / 3 switch report mode as access switch port access a VLAN 10 so here we can see that now they are in amber FS 0 / 1 and the 0 / 3 we assign to VLAN 10 now we will go to the interfaces fasterthan at Ciro's Lars - and faster third 0 / 4 such a port modest access such a port access a VLAN 20 now we can verify this support assignment chauvelin brief find here we can see the details here we can see the ports FA 0 / 2 + 0 / 4 is assigned to VLAN 20 name the faculty also we can see the for CFS 0 / 1 & 0 / 3 are assigned to VLAN 10 named students here the VLAN 10 and the VLAN 20 will communicate each other no it won't here we can verify that we will use this add a symbol P do and we will send from PC 0 to PC 2 that is from VLAN 10 to VLAN 20 here we can see it's failed but we can try from VLAN 10 to VLAN 10 PC 0 to PC for successful from PC to to PC 5 it's successful so here inter VLAN configuration we have to do now yes so here we have to do two more configuration the first one needs to be helped we enable IP routing on this multi-layer switch Yama's also we have to create two new interfaces on this multi-layer switch EMS to provide IVR coming to the configuration enable configure terminal here we are going to enable IP routing on this multi-layer switch by giving this command to IP routing now we will create the interfaces of for the VLANs 10 and 20 interface VLAN 10 here we can see the interface VLAN 10 change that state to up so here we will give the IP address here for the VLAN 10 be given the default gateway as over nine two dot one six eight dot ten to one now we have to give this to mask 255.255.255.0 5.25 5.0 now we will create the next interface interface VLAN 20 here we can see now this interface VLAN 20 also change the state to up will give the IP a trust so here we used 192.168.0 to 1 and this up it to mask 255.255.255.0 we can verify that show IP interface brief here we can see that a VLAN 10 and the VLAN 20 here we can see status is up also protocol up now we will verify the connectivity coming to pc 0 command prompt here are we will a ping to the default gateway of a VLAN 10 that is one nine two dot one sixty eight dot 10.2 one here we can see we are getting the replay also we will ping to the default gateway for the VLAN 20 that is a 2002 one here we can see we are getting the replay no we will ping from pc 0 to pc 3 in the same VLAN that is VLAN 10 coming to pc 0 ping two one nine two dot one sixty eight dot ten dot its toll here we can see we are getting the replay now we will the ping from pc zero to pc 2 that is from VLAN 10 to VLAN 20 ping two one nine two dot one sixty eight dot 20.2 here we can see we are getting the replay now we will do it from pc 2 which is in VLAN 20 first of all we will ping to the default to Gateway 192.168.0 to 1 here we can see we are getting the replay no will ping to 10.1 sure we can see we are getting the replay now we will ping from PC to 2 PC for you both are in a VLAN 20 it's 20 . 11 here we can see we are getting the replay now we will ping from PC to 2 pc 0 and that is from VLAN 22 wheel and 10 ping to 192.168.1.1 here we can see we are getting the replay here we can see the IP address of the interface VLAN 10 VLAN 20 but we configured our normal teeler such a mess well in this video we have seen how to configure inter VLAN routing using a layer 3 switch front see how in need out in this topic please comment below also if you liked my video give a thump and share with your friends and if you like to get this type of videos in future considered subscribing thank you

Channel: Tech Acad

Views: 23,273

Keywords: CISCO Switch VLAN, Layer 3 Switch, VLAN Switch, Inter VLAN routing

Id: g3-_mtCBC_Y

Length: 27min 17sec (1637 seconds)

Published: Sun Jun 24 2018