How To Make A Metal Drill Press Vise Without Welding | DIY Homemade Drill Press Vise

Video Statistics and Information

Video
Captions Word Cloud
Reddit Comments
Captions
good day guys in this video i will show you how to make a very simple but at the same time very sturdy and rigid metal drill press wise without welding stay tuned i started with this mild steel u-shaped metal beam left over it is 14 centimeters in width and 6 centimeters in the height measured anchor 26 centimeters which will be the total length of the wise next trim both sides to lower it from 6 centimeters to 2.5 centimeters in height to get a perfectly straight and level cut i use this homemade attachment for the angle grinder few bearings bolts and square tube converts this angle grinder to a rolling cutting machine of course those cuts could be made by hand but i wanted to try this jig in this build and it performed extremely well a single cut left a very nice and perfectly straight edge i drilled two three millimeters holes in both ends and with an angle grinder connected those to form a nice 38 millimeter slot on both sides i marked drilled and tapped and 10 holes here i want to make the vice a bit wider i used 25 by 25 millimeters angle iron pieces with drilled representing holes this will extend the wise bottom which mostly will be used as a clamping surface a bit of grinding was needed to make the whole surface perfectly flat the very last modification on this base was to drill and tap four holes in corners for m12 allen bolts did you remember that offcut i will use it and cut a pair of angle iron pieces for the wise jaws it not only helped to get the best use of the u-shaped metal beam but it has a very nice shape also i managed to get only two pieces from that leftover so the third one i cut from a regular angle iron found in my metal scrap here you could see that angle iron shape differences the bottom part is thicker than a vertical one which i like a lot two angle iron pieces placed at the base ends will be secured permanently while the middle one should be moved freely the process here is the same as in all connection points in its build drilling a pair of holes in each part to secure it with m12 allen bolts this angle iron is way too thin for my planet application so i make it thicker by adding this 10 millimeters of thickness flat steel strip as the inner corner has some radius i need to trim that steel strip bottom respectively to get that perfect fit angle iron was drilled and tapped to make mounting points for the reinforcing steel strip a pair of m10 allen bowls secure them to one solid piece here is the answer why such thickness was needed in this place i will use an m20 threaded rod as the main wise screw this is a good example of how to drill holes in strangely shaped metal parts without a drill press wise a simple support piece made from scrap food and a clamp did a job by looking at the thread it looks like one solid piece as i like to make stuff not only functional but at the same time looking neat i modified both sandwiched parts to a more lightweight and aesthetic look the smaller part gave the idea of how the angle iron should be trimmed too now both parts could be fixed permanently to keep the sliding jaw moving freely along the slot i will sandwich it with those two metal pieces after drilling and tapping all parts could be bolted together and it slides way better than i expected very nice to keep moving the sliding jaw i used an m20 threaded rod here i have to pay the price of using that nice shape angle iron jaw the bottom part is too thick for the m20 threaded rod not a big deal i marked and grinded the knitted groove with a rotary tool it took a while but now the threaded rod fits perfectly to attach the threaded rod to the moving jaw but at the same time let him spin freely i used those two metal strips first i marked and grinded a groove on the rod with an angle grinder later on i made a different size u-shaped cut in the each metal strip here is how it works the part with a bigger slot will act as a spacer between the jaw and the end of the rod the piece with a smaller slot will hold the threaded rod attached to the moving jaw and also let the rod turn freely if it makes sense when the holes were drilled and the parts mounted on the sliding jaw i didn't like how it looked so made small corrections this time i modified only those two parts i wanted to shape them in the same form at one time so i bolted them together with a pair of allen bolts while cutting and grinding them to the needed shape now it looks way better than before before attaching a threaded rod to the vice i need to mount a handle the perfect candidate is this 12 millimeters diameter stainless steel rod to join them together some drilling and grinding were needed the threaded rod got the hole and the slot in the middle meanwhile the stainless steel handle was shaped to fit in that slot to keep those two parts together i used a pen made from a nail and flatten another nail end holds in place and the handle moves freely time to mount it into the vice it spins very freely let's try it out on a drill press this vise has enough holding power to hold not only square parts the metal strip or round pipe makes no issues too what i like a lot that this device is low profile wide quite heavy and it could be used for all kinds of applications around the workshop for example i cut this metal strip without clamping the vice onto the workbench during the cut device moved just a hair which saves me time instead of clamping it yes yes yes i'm hearing you shouting why make such thing if you could buy it for a decent price well the reason is the same as with all other handmade tools you use what you have make it to fit your specific needs including shape size and technical characteristics and what is most important enjoy by building it i hope this was helpful thanks for watching and till the next time bye
Info
Channel: Well Done Tips
Views: 1,234
Rating: undefined out of 5
Keywords: diy, builds, make a metal drill press vise, simple diy metal drill vise without welding, diy drill vise, metal mini drill vise, diy drill press vise, metal vise, homemade metal vise, how to make metal vise, how to make drill press vise, diy metal vise, how to make, vise, diy vice, homemade drill press vise, homemade, how to, make, drill vise, how to make vise, making a metal vise, homemade ideas, tools, diy tools, diy ideas, tool ideas, welldonetips, Well Done Tips, WDT
Id: hMLDiEGru18
Channel Id: undefined
Length: 10min 6sec (606 seconds)
Published: Wed Dec 15 2021
Related Videos
Note
Please note that this website is currently a work in progress! Lots of interesting data and statistics to come.