How about my friends, colleagues or fans of upholstery, how are they today? My name is Mario Ernesto and this video, as always, those who follow me continuously you know what the purpose of my channel is is simply to show you works related to upholstery give you ideas if you are teaching yourself the purpose of my videos is to help you to advance in this learning process as soon as possible remember that this trade you will never finish learning because there are always new things to learn always always so what you are seeing on your screen is a 1969 cartoon in the us this car is considered classic and is worth a lot of money I am going to be showing you how you can make the console the part that goes between the seats I'm going to show you the interior of the car, it's going to be complete. I have several videos about the interior, I made the seats the carpet, but this time I'm going to show you how it has been ce the part that goes here in the middle of you come that lever that lever is very close to the floor as it is very close to the floor you have to make the console very low not so high you have to make sure it works I'm going to put two screws in the part in front to stop and one in the back here there will be screwed when one is going to be a console usually the client chooses the design one simply gives suggestions to the client if the one who is asking you for a design that It does not fit or that it does not go for example if I wanted a very high console keep in mind that the lever is small it is low there where one is going to give suggestions to the client I will be putting those cup holders you will always measure from the front to back how long the client wants it and then the height what he commands this time will be 45 x 8 the ways that I will be cutting the wood that is this very good wood as far as the height towards the client asks for a height that one is not going That height does not go to the client and one of them does it more or less according to the gear lever. I am cutting the wood 45 by 8 that wood is not straight. I will be making some cuts and I always say the corners, the corners, killing the edge. I have a piece here it will go like this 45 and here it has six and a half we will put it and if we have to make other cuts to adapt it there we will do it but we have the base of both sides what you see that I'm marking it is more or less where a separate piece is going to go, this piece is last and has its distance of six and a half because I have a cardboard of six and a half, it will work for you here to measure six and a half by 7 inches called by 26 and 10 by 19 7 by 26 we are going to cut two pieces and you see if you pay attention to this piece it is not straight because it is not straight because I want the front part to go wider there are some cup holders and I have to adjust the console to the cup holder many times the customer ask for the car stereo and in that part you have to make adjustments so that the stereo is as wide as higher it all depends on what the client is going to adapt I am adapting the disc because I am going to make a cut and I do not want that cut pass half an inch of the wood ok I am going to make a cut but I no longer want it to reach the middle of the wood that is a quarter of depth I put glue and we are going to nail the first piece and this is simply the idea that I I am showing him I put a staple there I put a mark and I already have the first stapled wood I am going to join the other wood we are going to put the same staples the staple I am using are an inch and a half long by a quarter wide and there I already have this part this is another part you did not tokyo he made some cuts to the wood notice what it is going to be now i am going to put that wood and it is not going to make you as one is going to enlarge the front part the cut I made is for that so that it opens the wood towards in front I have two boards nailed now what I am going to do is the hole where the gear lever goes and I do it about an inch of half an inch into the wood I am going to make four holes one in each corner this simply so that make it easier for me to get out that sought of wood now I cut it and I could have cut this before of course yes there I already have the eyes just now I sand down I already have the hole where the gear lever will go but this leads to a compartment to the back there you can see it from the front it is not straight I need a piece of wood here that more or less has the shape of the carriage trestle and the same size of the back you can see that curve well that is the curve that has the back part we cut this piece and that piece we are going to staple before the shovel as we always move away you can leave it manually or you can move it away with pneumatic tools we have here if you are not already there I made another hole in the back of where the gear lever goes, this is going to be a good compartment, I already have this a good distance away, we kill the edge, we don't want the edge to show through the material, although we are going to put foam on it, but many times When the edge is very aggressive, it is always visible and if the material is well stretched, a little bit touches the corner or the edge of the material in, say, the lever or an iron, it will break, we hit it a good distance, killing the edge of this wood. you can buy it in a type you can buy it in many places in the usa in dry wood it does not weigh i am sanding from the inside between less foam i put this to do much better i have cut two pieces you notice this piece well, just mark it according to the inside that is going to formulate a compartment, this that you see here is a piece of wood that I am going to add and it is going to go there is where it is going to go screwed I am going to put a screw that screw Llo grabs the console and goes to grab the part of the car, it will go there because as this is going to carry some cup holders, what then is to enter well where the cup holders are going to go, the cup holder cannot go very forward because it is yes the customer puts a soda or puts it in a bottle with water it will be difficult to put it in because it will stick on the front of the board that I already have the first portal these cup holders you can grab them in amazon or ebay there you grab them and They buy them I am going to use a special die to get that out and I have to be very sure of the measurement, usually the measurement is three inches three quarters for this spokesperson there is a glass holder that is 3 and a half inches and there is one it is 4 inches she says I already have both today I put the cup holder it is a little loose because it does not have the upholstery it does not have the material that it owes what is on the table what is on the table the bottom part like black that quarter foam inch usually that material is used in car roofs that is the amount of foam that I am going to add grip material more or less accommodated it well that there is no crease no crease because any crease crease that remains is going to take of thinking about upholstery not you like I'll cut that the bottom side there is no how short problem ras wood so I do not want to bend anything inward between less material is exposed out much better Well, I already have this now and it will be a cut exactly on the edge of the wood on the inside and they have that part outside here, simply the frame here is going to take a seam to this console I could have upholstered it in a single piece but I put a seam so that it molds well that part saying that it will have other design in wood, the top part I cut that the frames and I am going to put two marks with two marks in more than enough and now you I do not have a marked piece I mark the one that is going to go up I put something on top simply so that it does not move you are going to do the same and I give it the shape that you are cuts that I am going to make a frame on the board at the mere angle of the wood and then it is that one mark inwards and then another mark I already have this what follows next is to cut it and give it the increase for the seam I have the top already cut I just folded it in half to make sure that the two sides are love and that the marks are symmetrical as I just mark on one side I am going to put a piece below and the one that marks above and cut 2 to the same date the right and the left I put the two marks I already have this this is ready to be cooked for this time you have to have a little, I did not need much practice in sewing this is you can sew it on an industrial sewing machine because because it does not have foam the material is not very thick and so you will know those pieces I will sew the ot On the side basically the same make sure that those marks give you as always I always stressed the same marks if you make marks with a purpose so that the pieces are not crooked at the time of cooking after that you are going to put a on double stitching I have preferred here that it just have an overseam and it goes on the outside side piece it can go on the inside side there is no rule that says you have to put the stitching on the outside in a console either There is a rule that says that you are going to put it in the piece that goes up the top, you simply have to use logic or to the client it tells you where you want the seam is there is one in you you are going to put it there it is cooked and now what I am going to do is start to assemble it and you notice that I am putting glue on the inside, I am going to glue it on that side, I could nail it but it is not necessary, I am also going to put glue on the part in the stone has been able to nail I am going to put staples at the end but I simply put glue on them and let it dry while this is drying as it is going to carry a compartment it is much easier to upholster part of that compartment before nailing it because once you have You nail it, you will have to step on it and many times to mark the material or remove the wrinkles it takes time and apart it requires a bit of experience if you do not have experience that will struggle the way I am doing it is much easier It shows that I am tapestry before that wood I did not show you how to cut it but I imagine that you are going to figure it is something simple I nail it and it is ready it is simply part for a compartment that will carry this compartment I put glue here it is part From the compartment also that material that I am going to put is in the back on the back of the console imagine I am on the floor the entire console of it I want to make that compartment is going to be a bit co to start I will not be able to nail it because it will be upholstered otherwise I will not pen a piece I am already stepping on the inside of the console simply where the compartment will go I do not need excess material here there you do not see I do The same on the opposite side and I already have both sides, well, I will do the same in the back, I do not know that the client will not see the back, except if he bends down and is looking for that even with a mirror or a You can see the lamp but I always am but it is on the floor I advise you who are learning to do the same in this way the work is going well and it will look good I already have the inside upholstered ok interesting really let's put the glue another material this is the one that is going to go to the console is the cover of the console it is not where I am putting glue the part in the middle where there is that imbalance you are going to accommodate well that material is going to focus well when you are I make sure that the material is well centered so you are going to start gluing it in the meantime you do not glue it central or as well as you find any wrinkles or folds that are seen make sure that when that console is finished it will come out and this is Simple this is easy I put two staples in the middle, sorry to the edges and I will find that staple here I am going to remove it later it is simply to make sure that the console or the cover is centered, what am I going to remove that layer that I am putting on it then ok there I have it and here he pasted it that material has to remain following the shape of the console if the pieces that are going there are left in the air are not going to sit well you want it to feel good I already have the world well there the material and I cut it when the material is well molded I am going to cut it between because because the pieces that are going to go up will sit well they will assemble well I already have that here this is the back I put some staples and I'm going to cut ar and if the client who sits in the back seat is going to see there then that we have to finish it well this part is going to go here we are going to give it the shape is not this part and it is done we cut the cardboard we make sure it assembles well If the cardboard is tight inside now imagine with the upholstery going too tight leave a little loose that way when you are going to fit the upholstery well marked on the inside I have to make a pull out if a cut and the The cut I'm making is the one with the console, I could have cut it out of wood, I don't want it too thick, I'm going to stick a remote one, that has to look good, you can leave it by hand, you can leave it with a pneumatic tool, the line with Which one I did that has to be finite, everything manually, I am doing it, the bonding takes a little longer, yes, but since the piece is very thin and I use an air tool, it may damage it now, what it is going to do is ta For that piece I put glue I make sure it looks good let's glue it comes matte to the top that there are no air bubbles that are not marks many times when you do not put glue on it well the glue is marked and there you are seeing The back part I am not going to leave long because it is going to fold we are going to glue what is the inside part we are going to put glue here this I am putting is the ico I put glue and I am putting silicone this will go the other way around like this He is going to fit it well he assured me that if you do not have something like what I am I have in hand you can use what is the top of a spoon or a fork has no edge and that you can use here I just make a cut I want to mold that material to the shape it has that is the purpose of those cuts I grab it here and I'm going to put some staples and now and this console is taking the shape that part is easy to do there some that are very difficult s you have to lower the wood at an angle so that the material can be assembled, otherwise the material will not be assembled and I am going to cut it now here after having cut it here comes this to this part we simply put the metals so that we do not it was folded and the cardboard could not have been folded in the back to make you honest it would have been seen from my point of view it has looked much better I simply overlooked folding the cardboard the same cardboard that has the hole fold it and paste it and he already showed him a side how that is going here this side and I even mentioned that this layer I was going to remove and that is what I am going to do, simply the purpose of that staple was to stop the console in place on [__] the console I accommodate the part that is going to be enclosed and I put a staple formulated the compartment and it is easily upholstered, imagine if I just nail the wood and then how I would have done to upholster that compartment now I nail this wood ac Before I upholster everything that wood, that wood is where I am going to screw in the car, everything is coldly calculated and that part of the car is well, if there is something that interferes with the screws and there is nothing, that is why I am there screwing the wood if I had seen something like liquid hoses such as electric cables I move that wood more to the front or more to the back as we see that everything is now if I am going to nail it you will be the same the staple that I was using are of a quarter long I do not want very long staples it is simply a console does not have foam after I nail that I am simply going to cut the excess material and arrange it well there it is there although this is a piece of wood note that I am putting two pieces of Wood on the sides that have a good unevenness that is the way I want the part where the lever goes and a half that will go there I will make a few holes because I will put a few clicks of that f Orma the client will be able to put it off without any problem the clicks I am putting are black clicks but they are very good quality clicks there is a lot of black plastic that you put it on and want to remove it and it breaks these clicks I do not recommend this I can remove it, I can put it on and as it is of very good quality nothing is going to happen to it that either it is cold or it is hot here, the temperature I put them on, you saw that I lowered the wood simply so that it would not be seen the click here could have put some magnets there it would have been the same function I put a kind of cardboard there it does not take strength that is why I am using cardboard and I cut it around you if it were carried as something above I would have put wood but with cardboard will look good later I simply choose the same good and made sure that there is no fat left and I put it there there are some holes and there it will go in that I have to make a serve is where the gear lever goes since v a in the middle and it is more or less an inch and a half to two inches usually it is take out lol son ps - all the boards I am going to put foam of a quarter of a bone I put another cardboard on top of another color I did not show it the The cardboard that I put on top of another color was 1.5 thick, the one used for the hearth are viscera, that is why it looked like another color, he cut the foam here, leaving the eye without foam.Now we are going to upholster this by the way It has this we can upholster it, whether the seam is imported, we stretch the material, we nail the corners first and from there we go ahead, we will engrave it and we will nail it all around it if that had been so heavy in the frame and had to put some clockwork done The top one in three pieces and two on the sides with an overseam because the leather does not stretch so much the key and there it is that piece I am still going to do the removal of little glue and I am going to glue it, put some staples also this remove How is it a bit nice I cut it e in the middle of the type and on both sides and we are going to paste that so that no serve is visible that does not show the corners, the fake will stick it to you as the cardboard is thin, there is no problem if that is why you have to cut that in decrease boot step on it from the outside to the inside and this is already done I want to measure it and make sure it looks good ok soon tight but there it is there it is I am going to paint the wood it is not going to see that I am going to paint it I already have This or that this is the drawer or the door of the compartment, he puts it on a hinge many times there he puts vehicles on it, he puts a hinge on it or magnets are put on it after a hinge I am going to lower the wood because I don't want it to The hinge protrudes I want it to be at the same level with the wood, there is something simple and easy, we are going to screw that right now because right now because I am going to upholster it with the hinge on and I could have upholstered it and put the hinge on later, but it will be to see is going to see r the hinge the less you see the hinge much better we are going to measure this you are going to cut that piece notice what I am going to do here I do not measure the width and that I double the two I put a mark in half and it is normal it is not there is nothing new in that now the piece that will go inside like isco has been in a single piece I'm going to cut it half an inch smaller the one inside I'm just going to make a cover for that wood that's what I'm going to make and the cover is going to be in one piece I am going to cut it half an inch there it is and a half inch here that is going to be narrower from the inside you will wonder if you are going to do it in one piece because one side it is narrower and the other side is wider there the secret is there at the time of the kitchen that is going to formulate me this is the outside part and this is the inside part the seam will be on the inside part then I am going and we are going to sew it like this or as a console making sure that I did not put foam on them, the cover does not need you An industrial upholstery machine can cook this for you in an industrial machine for sewing clothes if you are going to sew leather the industrial machine that is clothes may work for you and they closed the cover we are going to cut the material as close to the seam and there we already have one side and notice here this is what the difference is going to be I am sewing part of the corner downwards I fold pulled the material discs or whatever goes towards Asia running down and the same cut here the good material already manages to demonstrate How to cut it is simple now I am going to put the foam of a quarter of an inch thick it is the same that I have been using I could have used another type of more solid foam but since the client here will not be able to put the hand that is exactly until very low by the lever the shape of the lever but we are making a compartment after I put foam in it I am going to put plastic on it it is always advisable to put plastic on it so that the f Unda slide well you fit well and there is the plastic we are going to put the cover this cover has to go well it does not have to be loose if it is loose it will not enter if it is affected it will enter but it is tight and scratch so much I can that break so make sure not to cut the very loose or too tight there is well accommodated the seam that runs to one side as well as the material and now I am going to nail it as you are going to nail it well because this less you want is Layer homework can be done, I'm not nailing the back there, the staple will not be seen, except if the client bends down a lot, he will see, he cut the material and I don't want a lot of excess material here, what I do below it is simply double and I am going to grease it exactly to the edge of the staple wood that I am using they are three-eighths long by three-eighths wide and that's it, I put a stake and I put the other one and I see that it fits well it is well that will go there í the customer asked personally I do not like I could have done something better to screw the back sack on the part of the way from here is where I'll screw the handle chromed make a hole with a drill from an eighth to screw that part here I am greener it goes in and out ok if you are not there I have painted on the part of the wood and there it will not be seen I painted it I put a tracer simply making sure that this to enter without any mishap and I put this I do not put everything because I am going to take it out later there is the console already because we are going to put this there it is we put it where it has to go and this inside and there it is I do not like how that part is in the middle cdc or I 'm going to do something for them, the lever moves, they face up before they have to move, this comes out and so I have planned to put a screw there and another here with one that I put back is more than enough, you do not need two screws, is this one if you don't I already put a screw on them, I'm going to put ot To make it stop, you have to check the bottom always when you are going to put screws that there are no liquid hoses that there is no that the electricity cable always notice the part of and a half where the gear lever goes I did something there simply so that it is not that he heard very aggressive there it turned out well I like how it turned out it is a simple console but it turned out well it turned out very well it is already dark I am using lights to show it and there is the compartment in the back very well that way it does not go all the way back it has a stop there it is as I mentioned it is a simple console if it is difficult for you let me tell you that there is much more difficult work is consoles that have an extravagant design that this one has to use The router to cut I showed you from the measure how I measured it how I prepare the wood all this is a procedure the upholstery is easy many times what it costs is that to give it the shape you do not I touched the upholstery, it was quick, I marked the material, I pasted it, and I put it in the car, there it is, this is what the top part looks like. Those cup holders give the console a lot of showiness. The client wanted it to be there as an extra space to put things. Also in front but due to the shape of the gas pedal it is very close and there is no space I told him that there was no space and if I did something very aggressive and if it is going to look ugly so it is if this was the design I just made some adjustments some recommendations and there it was reminded, the purpose of my channel is simply to give you an idea about what this Upholstery is, if you are teaching yourself and you have not subscribed to the channel yet, do it, you will learn a lot, you will not go away To regret for all those who have subscribed to the channel for a long time, thank you very much for the support you have given and continue to give them my name is Mario Ernesto, I am an inveterate upholsterer and I share works related to very upholstery and often this time it was a console from a 1969 Chevrolet Chevellel I have several consoles on the channel and I have others that are in the process of being edited so I can share them with you, stay tuned, see you very soon see you later bye bye
