Configuring RIP (Routing Information Protocol) in Packet Tracer 7.3

hello everyone now today I am going to show you how to configure our 2 or 2 network evita if rape ok let's get started go to in device let's take this pc in this laptop ok this laptop here and this PC here and take one sweets for this and for this and take two router one for this metro and one for this network and let's connect this network with or to wire connect these with these silly daddy connect this laptop 0 which is 0 and connect these with this ok let's configure IP of this first week on FB is ok with this we seem that if you connect these with this ways and we connect this way this way ok now let us configure this router let's leave IP of these port is 192.168.1.1 and on this on that is we are giving IP for 0 0 0 4 days 192.168.1.1 and similarly for these sorry for these we will be giving IP e 2.2 1 okay let's go to this router 1 and configure port t is 192 is 192.168.1 it inter and 24 to turn this on okay let's configure this PC zero go to desktop IP configuration go to static 192.168.1.2 let's copy these and IP of the Gateway would be the IP of this router zero okay similarly for this laptop zero go to test term good wipe configuration these IP you do 1.3 and gate will be 1.21 192.168.1.1 okay let's say that this working are not both 0 you see one and go to here and we see successful transfer of the packet now let's connect this router 0 and outer one with these so why are ok now we need to set up the ok we need to set up gigabyte port 0 / 0 / 1 / let's go here and give IP of 0 / 0 / 1 is 192.168.1.1 not 13.1 let's copy these and we will be IP off 1.1 is 3.2 okay let's put this here this here this here this is of this port okay go here go to 0 1 DYP 192.168.1 and turn this on and go to here boo 0 1 192.168.1 or 3.2 sorry and 2 dot 3.2 went on this on efficient packet from here to here left one has no functional ports Oh first we need to configure this IP of these in devices go to a static 192.168.1 is already given power router so 2.2 sorry 192.168.1.2 dot 1 because you to VIP of this router 2.1 similarly a destination one nine two six eight dot 2.3 and give to be 192.168.1 2.1 now we send packet from here to here this is failed because we need to set up either a static routing or so let's go here go to Reaper now let's go and add a new troop here 192.168.1.0 this means we are adding this network let's add again we will need to add 168 another network that one say 1.2.0 that means we are adding this this network let's get add and again we need 3.0 this means we need to add this network also so let's add and let's go to this router one go to three aper go to air 192.168.20.10 one six eight dot 1.0 1.0 means we are adding this network and we need to add this network assert that is 192.168.0.1 let us edit that again stands for this piece you piece okay etirsa fail I don't know why sometimes this happen let's go here with one two three okay IP of network IP DS beasties okay I think there is no program again let's quickly let's bury one for one success okay there is no any problem let's test area here it's a successful I don't know why some time like these happen in this packet pressure in this version let's go here let's go here which says again fail let's go here and let's go here Holly let's go here it's a successful okay I think no package and get transfer successfully from this network to this network wait okay okay I see successful okay let's see pc 0 2 laptop 1 it's a successful let's ping this network with this laptop ki PRP C 0 is the 1.2 okay let's go this laptop one go to common painting 192.168.1.2 okay and it is giving response control C exit okay this is deep routing in net true in cisco packet tracer and

Channel: Ishwor Panta

Views: 819

Keywords: Configuring RIP (Routing Information Protocol) in Packet Tracer 7.3, Rip protocol config, RIP configuration Packet tracer 2020, RIP config

Id: U_RAHlRL_oI

Length: 8min 12sec (492 seconds)

Published: Wed Mar 04 2020