СБОРКА И ЗАПУСК 16-ЛИТРОВОГО V8 ДВИГАТЕЛЯ SCANIA. ПРОБЕГ 1.6 МЛН КМ. DC16 PDE

Greetings to the viewers of our channel from all over the world! Today we will assemble and run a 16-liter 8-cylinder engine taken from a Scania R500 truck. Thank you in advance for watching this video, for comments and likes. Special thanks to those who subscribed to our channel. This is a great support for us. All lovers of Mechanics - enjoy watching! Before starting the assembly, the master spent a day and a half to clean the engine parts. The engine was very dirty. In the previous series, we showed this. We start as always with the unpacking of the cylinder liners Friends, the video turned out to be quite large - since the engine is very large with a lot of parts I tried to make the video as short as possible but at the same time I tried not to miss anything Probably with your permission a little later I will release a shorter and more dynamic version of this repair We install rubber seals on cylinder liners We also install rubber seals in special holes in the cylinder block Friends, 4 people work in the room at the same time. Therefore, there will be many sounds of the instruments in the video. I didn’t put on music - in order to preserve the sound of the working atmosphere Lubricate the cylinder liners with special grease Proceed to install the cylinder liners - the camshaft does not work in this engine lubricate 2 camshafts before installation we introduce the camshaft into the cylinder block turn the cylinder block unscrew the crankshaft holders install oil nozzles they supply engine oil to the lower part of the piston; use a torque wrench; install plain bearings in the cylinder block ; lubricate the crankshaft ; We tighten the bolts according to the scheme provided by the manufacturer of this engine - it even rotates Friends , I will shorten all the processes with tightening the bolts in this video washing using special chemicals heat exchanger cover oil pump camshaft gears right and left Timing gear gears are installed according to the marks crankshaft gear oil pump tube flywheel housing install gasket dynamometric pneumatic gun) flywheel replace bearing cover heat exchanger engine brackets front cover pistons install piston rings install plain bearings in connecting rods install pistons in the cylinder block rings are installed with holes in 3 directions - like a Mercedes icon, tighten the connecting rods according to the instructions oil dipstick body starter oil intake oil bath lubricate the joints with germ tic selection of bolts fuel filter housing coolant pump housing coolant pump fan drive bearing good booster pump power steering pump belt tensioner rollers already similar to the rocker axle motor This is the mechanism that is used to transfer the energy of the camshaft cam to the valve stem heat exchanger centrifuge filter housing will now be many different pipes and small parts we repair the cylinder heads we changed the valve guides and exhaust valves we grind the valves we also corrected the valve seats we install the valve stem seals the valve springs the valve crackers the cylinder head gaskets we install the cylinder head the cylinder head bolts we also tighten the fuel rails inlet manifold the spacers for the cylinder head covers Quality control Rods valve lifters fuel injectors Valve tappets Rocker arms Oil filter housing Engine control unit with wiring we lay the engine wiring generator belt belt tensioner turbine Engine breather - a valve designed to relieve excess pressure that is formed during the operation of the power unit the filter of this filter was not filter - centrifuge oil filter fuel filter exhaust collector Compressor fan Valve adjustment. There is a separate detailed video on the channel on adjusting the valves on this engine, the valve covers are ready , we install the clutch friends, the engine was assembled for you, the process was quick , I had 10 hours of filmed material) we install the engine on the car , we connected the gearbox, fill in the technical fluids, pump the fuel and we will try to start engine on the first try) you can put a coin on the edge difficult after repair we leave the engine to idle a small advertisement: we buy trucks in any condition for dismantling for spare parts we have the largest dismantling of trucks in Russia we buy whole, broken, faulty, burnt we pick up trucks and special equipment all over Russia on our own and at our own expense my phone number is indicated under this video I am always in touch on this our video has come to an end. I hope you liked the video Thank you for watching and subscribing to my channel Friends, I'm sure that among our viewers there are many people who produce interesting types of work related to trucks , someone works in industries related to the theme of our channel if you have a desire to share your work with the whole world, and our channel is watched by people from all over the world, please contact me, my contacts are listed under this video, I myself can come to you and shoot a video about your work, or you can make a video about your work yourself and I will publish it on this channel this applies to viewers from all over the world I am starting to shoot a new video I wish you all good luck, take care and see you! thanks for subscribing to the channel

Channel: RAZBORGRUZ - РЕМОНТ ГРУЗОВИКОВ

Views: 2,076,072

Keywords: truck engine repair, ремонт моторов грузовиков, scania repair, ремонт скания, engine overhaul, капитальный ремонт двигателя, scania hpi, топливная hpi, про моторы, pakistani trucks, пакистанские грузовики, megafactories, мегазаводы, all about trucks, все о грузовиках, разборгруз, truck accidents, аварии грузовиков, scania trucks, грузовики скания, разборка грузовиков, выкуп битых грузовиков, Trucks tv, большегруз 40 рус, дальнобойщики, дальнобой по америке, razborgruz

Id: BFIZXK0lyGo

Length: 44min 41sec (2681 seconds)

Published: Fri Feb 10 2023