and FIVE TOOLS to build your palletwood empire!

Video Statistics and Information

Video
Captions Word Cloud
Reddit Comments
Captions
[Music] one more just one more project. you'd think after 5 years I'd know that  it goes the other way around. all right. just one   more promise! okay this is the pallet the CNC came  on it does have very thin slats, so I'm going to   try and do this with one pallet, because I don't  really want to go hunting, not that it's hard if   you want Pine, there is thousands of them. The  top side actually has these 25 mm slats so see   how we go see how far we can stretch this bad boy,  I going to bust down in here because I don't want   to get sun burnt. ok probably wasn't going to  get sunburnt in the 2 minutes that this takes all righty uh quick update the table saw, the  new table saw is happening there was a few   little holdups somewhere in the supply chain so  stay tuned. so after emotionally farewelling my   little yellow friend here my wife asked me if we  should simply buy a small bench for her Studio,   it was about 180 bucks and I was like hell no,  I have 4 days off, I have a pine pallet and I   can whip up something suitable and also get to  make a video. the plan is to keep this as simple   as possible and also chat about tools along the  way tools to get started tools that I recommend   you get okay just quickly I'll show you my latest  straightening jig which I love the most uh these   ratchet clamps they're on bangood just search  ratchet clamp bangood they're very good. okay   it relies on the Dove tail in your straightening  jig now I made my Dove tail didn't have a dove   tail bit just cut some angles with your circular  saw table saw and then glue the top piece to the   bottom piece then you have your dove tail action,  these are the fastest way of straightening pallet   wood are way better than toggles way better than  the screw Downs super fast the beauty is I don't   need to do it in this video they straight enough  to go through the table saw safely. sorry so why   these are much better and faster is because most  of the time pallet wood is always of varying   thicknesses the ratchet clamp plunges down onto  the Rando thickness the quickest you'll find that   the toggles although good, they require a lot  of fluffing around when you have the different   thicknesses and to get the right tension and the  screw down hold down clamps are slow for obvious   reasons but saying that this particular design is  great for putting a straight edge on a slab now   what I'll probably do is make a new one of these  but I'll still set it up with the dovetails so   the ratchet clamp will do both things all sorts  of bits and pieces tapering all the things these   I can use them somewhere else I recently went on  the Wood Biz Podcast and the topic came up about   what tools you would start out with if you could  go back and start again so I wanted to use this   video just to highlight a few on the podcast my  advice was to just get started, and then find a   way to get a table saw into your Workshop as soon  as possible. do what you have to do to make that   happen it is simply the most versatile tool that  you can have in your shed and it is an absolute   Workhorse. I've picked a width of about 35 to  40 mm this gives me two boards per pallet slack   and I'm then going to resaw the boards into  two different thicknesses because I have both   Thin and Thick palletwood boards I'm trying  to maximise what I have from this particular palletwood this lamination technique will let  me create longer than a standard pallet board   slab stick with me all right thanks  for sticking with me I have whipped   up a quick clamping board and all I'm  doing is lining up the lengths of the   same thickness board to create a longer slab  as long as the boards are the same thickness   on each run it will all clamp together  nicely and it will be super strong of course you may have noticed I have not cleaned  off every face of every single board the goal   is to have every face as clean and flat as  possible but that may not always be perfect   or possible with the tools that you have what  we want is to avoid any moisture getting into   those voids between the boards that is where  the problems and separations will occur so   stick with me I have my reasons but in short if  your piece of furniture is out of the weather   and it's got some sort of protection on it it is  going to be fine especially this one laminated interlocked bit of tight ass advice here don't go  too tight ass on the grease proof paper this one's   about two bucks and it is not greas prooof enough  spend the four bucks and save yourself a heap of grief. I'm going to turn the fan off $2. second tool I recommend getting a as early  on as possible is a router again super duper   versatile and great for flattening pallet  wood slabs and other types of wood slabs now   I have well and truly done my apprenticeship  flattening slabs with a router so I'm going   to run these slabs through the thicknesser  get them nice and flat both sides and move on I have these pine legs from Mk 1 dining  table I made and I'm going to use those   as the timber is kind of sentimental to me  and my wife so this was a perfect project   to use those up so with that in mind this  is probably a two pallet project I'm not   sure I understand again there are plenty  of pine pets out there nobody is arguing that third tool is a belt sander with 40 grit  sandpaper this is going to remove material   very fast and also clean off your slabs quickly  after you have flattened them with a router you   will use this Beast Peeps and again if you  listen to that podcast you'll hear Dean   talk about the belt sander professional  furniture maker still smashes out the belty again the router is very versatile at   cutting circles and segments of  circles and in this case half circles [Music] ideally getting through the thickness of the  slab with the rou a bit would be great but if   you can't you can just bust out a jigsaw only  use a jigsaw a handful of times per year so   a cheap and or nasty will do me just fine  for those occasions DIY entry level tools   are perfectly fine to just get started but  also just have lying around for when you do   need that Rando tool here and there you can  beat the snot out of them if they break I'm   sure they're going to be under warranty  if you are picking up what I'm putting [Music] down I'm going to use the table saw for  most of the frame which again is to   show that if you make a few Jigs and sleds you can   cut heaps of different joints and avoid  using a handsaw and a mallet and chisel again I did make a rookie error here I  use my stock to set the size of the cut   to make forgot about the thickness of the  blade so therefore that joint was out by   the thickness of the blade it is also the  reason I decided to do one entire leg and   Corner first in case I made any blunders and  it just let me iron out the process for the rest [Music] [Music] next tool you'll probably want to get and  you probably had it well before your table   saw is a MIT saw again very versatile for  making different types of cuts with ease   and this saw will be another work of course for  smashing palletwood down to varying sizes and [Music] [Music] shapes I am trying something a little bit different  with these particular corner joints simple but   strong they are not exactly aesthetically pleasing  just yet so stick with me all righty thanks for   sticking with me so I'm going to put a round over  on all the edges to try and unify this Frame and   improve the overall look keep in mind this is just  a little bench to hold a few random asses here and [Music] there [Music] now before I get to the beauty shots I want  to quickly talk about the biggest issue I   have right now in the shed space space the CNC  has a very awkward footprint to fit anywhere   in my shed and simply something has to go so I  don't go insane trying to operate in this small space so after about two copies of consideration  I have decided to give the mitur the ass and   dedicate that space to the CNC if there is one  thing that woodworking has taught me it is that   there is many ways to get the same job done I had  no regrets selling the bansil I had no regrets   selling the bansel and I already know I'll have no  regrets saying goodbye to the monitor I have many   other spinning blade options to get the job done  and I'm actually looking forward to the challenge   of trying to to figure things out without the  Mota did not think I would be uh hanging out of   this hole again for a while it may even let me  get to come up with a few new jigs which I'll   get to show off here anyway okay just one more  thing I have created a second Channel and it   is called damade unofficial and it is where I am  considering dropping some other videos that are a   bit more talkie talkie maybe some more Deep dive  how-tos as well as other Rando bits and pieces   that I want to show off around here in the shed  uh the link is down below if you are interested   and that will help me sort of gauge of how much  time and energy I put into that channel and it'll   obviously give me a good idea of how many of  you want to see more of my backyard Bandit [Music] activities [Music] let's call this semi semi- temporary  let's have a quick look outside what   we're doing here so there's the original  white board that is just providing some   waterproofing so my other dodgy roof water  falls onto this dodgy roof and we're good to go so a simple Pine palette whitewashed  and clear coated this style of finish   was one of my most popular in my earlier  palletwood Furniture projects and it still   is especially for hallway tables the  frames and pine is the most accessible   when it comes to pallets it is easy on your  tools and blades and it is perfect to learn   a few skills before you start laying down your  cash buying potential more more cooler harder   Timbers or before you start using those  really nice hardwood palettes that you   are going to find because you're just going  to keep looking okay catch you [Music] later
Info
Channel: Dainer Made
Views: 103,503
Rating: undefined out of 5
Keywords: palletwood projects, woodworking
Id: 5TN4S4Ayhbc
Channel Id: undefined
Length: 18min 18sec (1098 seconds)
Published: Sun Oct 29 2023
Related Videos
Note
Please note that this website is currently a work in progress! Lots of interesting data and statistics to come.