Air Powered Helicopter

Video Statistics and Information

Video
Captions Word Cloud
Reddit Comments
Captions
i usually start off my videos by talking about a physics or engineering topic that's related to the thing that i'm planning to build however i've been working on this project for about eight weeks now and it's not going to work this is pretty much the full extent of what i've built as you can probably see it doesn't resemble anything that you've just read in the title of this video so i think what i'm going to do is i'm going to show you everything i've been developing and hopefully we can piece together some of these parts to produce something that kinda does something this video is sponsored by kiwiko more about them later for a helicopter to fly there are three main requirements the first is it must produce enough thrust to lift its own weight the second is it must have some form of stability or control to keep itself level and prevent a crash and the third is all the torque produced by the rotor must be counteracted either with a tail rotor or another rotor that spins in the opposite direction after reading the comments on the previous air turbine video several of you suggested i should build an air powered quadcopter and i agree four turbines attached in a cross-formation all controlled by compressed air will be awesome for a drone to sustain smooth stable flight it's very important that the propeller and motor specifications are matched for their intended rpm for example this tiny motor is designed to spin at 30 000 rpm but this large propeller is designed to spin at just 5000 rpm so it would be like trying to put tractor wheels on a formula one car but aside from the thrust produced the quadcopter is controlled by varying the speed of its propellers and generally smaller propellers have less rotational inertia which means they require less torque to change speed and since the turbine knife design doesn't have much torque i'll need some smaller propellers this means adjusting the turbine gear ratio to match the optimum rpm of the smaller propeller the only problem is i can't get it to produce anywhere near the amount of thrust of the larger propeller which i can only narrow down to the smaller propeller being less efficient i then mounted an electric motor on the thrust test stand to spin the propeller at a controlled rpm which allowed me to measure the power being drawn from a battery this is essentially a basic method to measure the propeller efficiency by slowly increasing the motor rpm i can log the power consumption and the thrust produced to blot a thrust versus power graph and from this we can read the efficiency of the propeller for example at 10 watts of power consumption this propeller produces 1.16 newtons of thrust or equivalent to lifting 118 grams i then repeated this test with the larger propeller and the results were very clear but the same power output the larger propeller produces nearly 40 percent more thrust which is a huge difference in efficiency when we're searching for small five to ten percent improvements in the turbine design so this is where the problems begin the larger propeller is so much more efficient than the smaller propeller that i basically have no other choice but to go with a larger one but using this on a quadcopter will be difficult to control as well as the frame will need to be large enough so the blades don't overlap meaning it will weigh more so i think what we need to do is go back to square one and go with a helicopter design the only thing we need to worry about with the helicopter design is that because it only has a single large rotor it needs to have a tail rotor to counteract the torque produced by the main rotor and because the tail rotor pretty much only blows air sideways it's basically consuming the compressed air that we need to use as the helicopter's fuel but it's not producing any useful thrust to lift the helicopter off the ground but what about a helicopter with contra rotating blades like the new mars helicopter where both blades spin in opposite directions this would counteract any rotor torque but would also mean we need to build a gearbox and shaft system so that each propellers could spin in opposite directions which isn't a problem for an electric aircraft but because these air turbines can't produce much thrust it's probably going to produce too much friction with a gearbox and also a lot of weight the other option is to mount a turbine on top and another turbine underneath the craft as this will basically achieve the same thing of the torques being counteracted but we won't need a complex gearbox and shaft system but there is another issue two turbines means added weight and also twice the air consumption so we just add more compressed air bottles right well this starts to spiral into a vicious circle of needing more thrust and then to produce more thrust we then need more compressed air storage which then adds more weight and then we need more thrust again to lift that extra weight and so on and if we look back on the propeller efficiency graph at low thrust values it produces about 20 grams of thrust per watt but at higher thrust values it only produces 13 grams of thrust per watt so as the thrust is increased the propeller efficiency decreases probably due to extra drag of the propeller having to spin faster so what we need to do is produce the lightest possible craft that we can with a single turbine and a single plastic bottle something interesting i realized whilst considering a tail rotor is instead of mounting a turbine to the end of a tail boom why don't we use a small nozzle to bleed off some compressed air since torque is the product of a force at a perpendicular distance if we have a really long tail boom it will only require a small amount of thrust to keep the helicopter pointing straight let's take for example one of the turbines is mounted on a 0.2 meter long tail boom it produces about 1.4 newtons of thrust at 4 bar of pressure which means a torque of 0.28 newton meters is produced with a total weight of 58 grams whereas if we take that same nozzle from the turbine mount it on the end of a 0.8 meter tail boom it produces far less thrust but we get the same torque produced whilst consuming the same quantity of air but it now weighs just 27 grams which is a huge difference i then came across a youtube channel called science-ish and he made a video where he produced supersonic shock diamonds by burning alcohol inside of a plastic bottle and guess what i'm also using a plastic bottle which could suggest my nozzles are producing shock diamonds too to see if these nozzles are actually producing supersonic flow i've decided to build what's called a schlieren imaging setup essentially there's a magnifying glass lens right here lots of people would like to use mirrors from telescopes but i couldn't find any for a reasonable price so i picked up this magnifying glass lens off amazon for pretty cheap and at the focal distance of this lens is a small point of light it's basically an led mounted inside of a 3d printed housing now at the other end of the focal point of this lens is a camera and positioned just in front of the camera is a very sharp blade and the idea of this setup is that over this long distance air is going to refract any kind of light that travels through it so basically if you have a high density portion of air or a low density portion of air it will either be refracted up or refracted down so some of the stuff that is either high density or low density will hit the knife and will cause a shadow in the camera image it's probably better if i give you a quick demo with a candle lighter okay so the high speed camera is recording so i should just be able to light the candle in front of it stop the high speed camera and then if we take a look at this should be able to see some pretty cool airflows coming out of that that's so cool so i've now got the nozzle mounted in front of the lens and i've got a pressurized bottle down here it's not actually pressurized yet but i'm just about to pump it up and then we'll see whether we're actually getting supersonic flow we're going to play and is there anything there unfortunately the resolution of my high speed camera isn't great and it was also slightly out of focus so i ran the test again using my stills camera and captured this awesome shot where the shock diamonds are clearly visible but what does this mean well maybe i can design a bell-shaped day level nozzle like you see on rocket engines now i have no idea about that area of fluid dynamics but fortunately the clever folks over on twitter saved me a lot of experimentation though i still had to test the theory so i printed two more nozzles with a very small expansion section and there is definitely a visible difference in the slurring imaging however the theory was correct the simple standard nozzle produced the most thrust in the spirit of keeping it simple i attached the turbine directly to a carbon fiber tail boom and because the tail boom is hollow if i seal off both ends it can be pressurized at the turbine end of the tube i designed a three-way fitting that allows the incoming air to pressurize the tail boom but also acts as a nozzle to power the turbine then at the other end of the tube i command a 90 degree nozzle which will act as a tail rotor with the propeller and air supply attached i can spin the turbine and see how the torque compensation works and it seems to be working better than i expected so i need to reduce the diameter of the tail nozzle but at least it seems to have enough thrust i then printed a very basic rotor head which was inspired by peter shreepool's rubber band helicopter where the blades are just attached to a pivot and then a weighted stabilizer bar is attached at an offset angle this stabilizer bar is very common on small scale helicopters and the idea is that the gyroscopic stability of the bar will keep the helicopter level during flight or at least long enough for the air supply to run out so with the helicopter suspended from a bearing mounted string it's time to see if this thing is going to fly aside from the air supply tube pulling the helicopter around it's actually looking a little promising so let's attach a one-way inlet valve to fill the bottle and see if it can run on its own air and without the safety tether it seems the nose of the helicopter pitches up very violently as soon as it takes off which throws the stabilizer bar way out because it's only restricted to about 30 degrees of tilt i think the reason for this is the air supply acts as a nozzle once the helicopter lifts off producing a fast jet of upwards moving air which hits the helicopter nose i also noticed the turbine barely runs for more than a couple seconds almost like the propeller blades are just freewheeling which suggests the bottle isn't being pressurized to fix both these issues i redesigned the inlet nozzle with a larger diameter so there is more airflow into the bottle than there is exiting via the turbine i also designed the nozzle to vent air sideways once inside of the valve so when the helicopter takes off there isn't a vertical stream of air pushing upwards on the nose the only problem is the new large diameter inlet nozzle has too much friction for the thrust of the helicopter to overcome so why not give it a little help for one final attempt to see this thing saw into the air i built a small lever to assist it off of the nozzle the bottle definitely seems to store more pressure now as the turbine spins for a lot longer so let's remove the safety tether one last time just a little more pressure should do the job i'm going to pause right here and show you the slow-mo instead because not only does everything look better in slow-mo but it also makes the flight time seem longer [Music] i honestly don't know what else to try out this project i just don't think it's gonna work but you know what does work kiwico crates kiwico create these awesome crates that each contain hands-on projects that are designed to expose kids to science technology engineering art and math and they never fail to impress me the crates are designed by experts to not only be educational but also great fun and each box includes all the required supplies so there's no need to go to the hardware store as well as a clearly laid out kid-friendly instruction manual every kiwi code create is different and there's over eight different subscription lines each catering to different age groups and topics so there's something new to learn every month cubico believes that the best way to change our world tomorrow is to teach kids the skills of problem solving and innovation today and i completely agree learning how to problem solve really opens up future ideas and opportunities i just wish i could improve my table tennis skills you can get 50 of your first month of any kiwico crate by going to kiwico.com forward slash tom50 the link will be down in the description below thank you to kiwico for sponsoring this video and thank you very much for watching if you enjoyed this video it'd be great if you could leave a thumbs up down below if you're new to my channel and want to see other projects like this then please click subscribe down below and a massive thank you to all of my supporters over on patreon.com for making this project possible i honestly couldn't build these kind of things without your support so thanks again for watching and i'll see you in the next video goodbye
Info
Channel: Tom Stanton
Views: 506,920
Rating: 4.9038181 out of 5
Keywords: Air power, compressed air, pneumatic, compressor, pump, 3D print, 3D printed, Aircraft, DIY, Engineering, homemade, aerospace, helicopter, rotor
Id: fkTK4F7Xqqo
Channel Id: undefined
Length: 14min 13sec (853 seconds)
Published: Thu Apr 22 2021
Related Videos
Note
Please note that this website is currently a work in progress! Lots of interesting data and statistics to come.