- On December 17th 1903,
the history of the aviation was changed forever
when the Wright brothers made the world's first successful flight. You might think that they're
design was so simple. The propellors move the aircraft forward, the wings produce the lift and the aircraft stays in the air. But when you examine it closely, you will amazed but the
numerous ingenuous technologies these high school dropouts
developed 100 years ago. (upbeat music) Their design was so complete that even the current modern aircraft used the same principles of flight. First thing's first,
to make an aircraft fly you have to first overcome
the pull of gravity, or in other words, you have
to produce a lift force. The Wright brothers borrowed the idea of lift generation from their own earlier experience on gliders. They knew that when air
float over a curved surface, it generated a lift force. The higher the speed, the
more would be the lift force. An increase in angle of attack also increase the lift force. How is this lift generated? That's a topic for another video. To make the aircraft move forward, two propellor blades were used. They produced thrust force, again, from the same airfoil principle. The thin propellor blades were a clever design choice. Until then, the common belief was that an aircraft propellor should be something like that of a ship's propellor. However, the Wright brothers proved that to work efficiently in air, a high speed narrow blade
was the ideal choice. Moreover, you will notice that the blades were rotating in opposite directions. This was another crucial design decision. Without this, control of the aircraft would not have been possible. We will learn about that
at the end of the video. The blades were driven by an
engine which sat on the wing. To fly an aircraft, you have to obey the following force equations of flight. To come up with an aircraft design which satisfy these equations, the Wright brothers developed their own lift data by abandoning all the wrong lift data that
was available at that time. The Wright brothers' wing had a top point near the leading edge. This design produced more lift than the top at centre
design used at that time. With an optimized wing design alone, this aircraft would not
lift from the ground. The Wright brothers
realized that the existing heavy automobile engines being used were the main villains. They had to make the engine lighter without compromising its power output. Only a powerful engine could give the aircraft a good speed. As explained earlier, the more the speed the more the lift. Unable to find any such engine, with the help of their mechanic, the Wright brothers designed and built their own engine. A light-weight, 12 horse
power petrol engine. Even before the new engine development, the Wright brothers had calculated that they needed an engine of less than 200 pounds in weight, with at least eight horse power to meet the equations of flight. To reduce weight, they even cast the crank case with aluminum, a first at that time. They painted the crank case black so that their competitors would not know about the construction material. You can see the details
of the chain and sprocket mechanism used to transfer power from the engine to the propellor blades. With this design, at
proper airplane speed, the lift force would overtake
the gravitational pull, and they would have take-off. Did you notice a rail
track in this visual? That was another clever design decision from the Wright brothers. They knew that it was impossible to get a good airplane
speed in the sandy terrain, so they used a 60 foot long rail track arrangement
for a smooth take-off. The Wright brothers' main innovation was the development of
successful flight controls. Aircraft crashes were a common issue in those days, and nobody
knew how to control them. To have a successfully flight, the Wrights had to control
their plane in three axes. Pitch, roll, and yaw. They again relied on the principles of the airfoil to accomplish this task. To pitch the airplane, the right flyer had an elevator arrangement at the front. You can see that by moving this lever, a rope mechanism change
the angle of the elevator. If the elevator's rotated up, there would be an upward lift force as per the air flow principle. The torque produced by this lift force could push the whole aircraft up as shown. To push the aircraft nose down, they just did the reverse. In modern airplanes the
elevators are fitted at the back. To roll the aircraft, Wilbur
Wright had a great idea: wing warping. It was clear that by twisting the wing along its length at one end, the angle of attack would be positive and the other end, it would be negative. This would obviously
create a lift differential and the airplane would roll. To the understand how the Wright brothers practically achieved the wing warping, let's have a look at this animation. The pilot controls a
cradle, using his hip, which in turn controls two
separate cables attached to it. The cable movement makes the wing warp through a clever mechanism. This is a brilliant mechanism. We need a separate, dedicated video to understand the details of it. In modern aircraft, ailerons are used to generate the lift differential. However, when the Wright brothers tried to roll the aircraft
using wing warping, the result was disastrous. They noticed that along with the rolling, the airplane took an
unintended turn as shown. They called it a "steering
reversal problem." This phenomenon is now
called, "adverse yaw." The physics behind the adverse yaw are now well understood. The airflow above the
high angle wing region produces high drag. On the other tip, the drag force is low. The difference in the drag force makes the airplane yaw as shown. The Wright brothers overcame this issue with the help of a rudder arrangement. If the aircraft was yawing in this way, they turn the rudder as shown, in such a way that the
torque produced by the rudder would exactly cancel
the adverse yaw torque. Here the Wright brothers
made another smart move. Since the rudder had to be operated whenever there was wing warping, they connected the rudder and wing warping controls together. Both these motions were
simultaneously operated from the hip control. By using these controls effectively, the Wright brothers were
able to give the aircraft the stability needed. Pitch the aircraft to
climb up or climb down, and make a smooth turn
by banking the aircraft. Now back to the interesting question posed in the middle of the video. Why did the Wright brothers use opposite direction of
rotation for the blades? This was to cancel the gyroscope
effect of a rotating wheel. Any rotating object has
an angular momentum. Assume the Wright brothers
designed the aircraft with the blade spinning
in the same direction. Now the pilot decides
to pitch the aircraft by lowering the elevator. The lowering of the elevators would obviously produce a torque as shown. However, the airplane would
not pitch upwards as expected due to the angular momentum of the blades. Instead, it would take an
unexpected side turn as shown. This unexpected phenomenon is known as gyroscopic procession. Gyroscopic procession conforms perfectly with Newton's Second Law of Motion. You can see that the direction of change in angular momentum is the same as that of the torque applied. The only way to overcome
such unexpected behavior is by eliminating the very cause of it: the angular momentum
of the spinning blades. That is exactly what
the Wright brothers did with two blades spinning
in opposite directions. It is astonishing to discover that the Wright brothers thought about such detailed engineering points, despite their limited formal education. Did you notice that the pilot's position was not in the middle of the aircraft? Please support us by
clicking the help button if you are astonished by the
marvelous engineering feats that the Wright brothers accomplished. Also, let us know in the comments box why you think the Wright brothers decided to position the
pilot slightly off-center. Thank you.
