How to Set an AViPAS IP Camera to your LAN (Part II)

so to connect the computer and the camera you need an ethernet cable and on one side you're gonna have to plug it in to the computer and then on the other side you need to locate the ethernet port on the camera and then plug the other side of the ethernet cable into the camera and once you see the light and ethernet connection should be established the camera ip address is 192 168 516 and so since you want your computer to be to access the camera through the ethernet connection that you just did you need to change manually change the computer ip address to 192.168.5160 now the 160 it doesn't have to be 160 but it has to be has to be unique from 163 so to manually change it right click on the internet icon and click open internet network and internet settings once there scroll down until you see network and sharing center which you should click on once you're in the network and sharing center find the ethernet make sure to make sure that it's not your internet ethernet because you might may have multiple ethernet connections so make sure that there is no internet access and click on that ethernet and then click on properties and then once you're in properties find something called ipv4 and then double click on that in the ipv4 properties click on use the following ip address and input the ip address i just talked about which is one nine two one six eight five and then the subnet mask will input itself and then for the default gateway put 192 1685 and after you inputted everything press ok and then press ok again this is important press it twice and then close the window after you have changed the ip address enter the ip address of the camera which is one which is 192 168 5 163 to a browser and then log in the username is admin and the password is admin as well and then your camera should be connected and you can access the device on your computer so for these models for the 1560 models there's not much different the only difference is that the ip address that you're going to be changing your computer to is different so the camera ip address for these cameras for the 1560s and all the other models that i listed is 192.168.10088 and you're going to be changing your computer ip address to 192 168 100 100 80 and default gateway is 192.168.1001. so to do that you again click on the internet icon right click and then open open network and internet settings and then you scroll all the way down and then you go to network and sharing center and then you find the ethernet that has no network access and then you click on that and then you click on properties and then you find the ipv4 internet protocol version four double click on that we'll use the following ip address which i just wrote down and let me go get that to get to that is so you're going to be changing it to 1 9 2 1 six eight one zero zero eight zero and then the subnet mask will enter itself and then the default gateway is one nine two one six eight one zero zero one make sure for ip address and the default gateway the first three sections are the same and then you press ok and then you press ok again and then you close this window and then you go into a web browser and then you type in the ip address of the camera which is 192.168.10088 it may ask you to log in the username is admin and the password is admin as well and everything should work okay so now that you have connected your computer to the camera with the ethernet cable well you can what we're going to be doing now is putting the camera into the local area network or the lan so what you're going to do is you're going to go to the camera web page and you're going to log in so the username is admin and the password is also admin you're going to go to configuration and then you're going to go to ethernet once you're in ethernet a bunch of stuff will pop up so there's ip address subnet mask default gateway and mac address so the only two things you're going to be changing is the ip address and the default gateway so previously i asked you to find the ip address ip address and you're gonna find the ip address that you found through the command prompt so my first three sections is one nine two one six eight zero so i'm gonna type in one nine two one six eight zero then after that this last section you can put any number you just have to make sure that the devices in your local area network don't have this last number so the last number has to be unique for each device so i'm gonna do like one two one for example and the default gateway is going to be changed to 192.16801 so for the default gateway the first three sections need to be the same and then the fourth section is just one okay and then you press save and then you go to reboot and then you press reboot press yes and then your device will reboot and then after and then after your camera is rebooted remove the ethernet connection between your computer and the camera and then take the ethernet cable and then connect it to the camera and then the other end will go into the router and then after that you can type the you can type the com you can type the camera ip address that you just changed into the web browser so mine would be 192.1680121 and your camera should pop up just a reminder is when you go into configuration there's a thing called network port when you're there don't change anything because you might actually lose access to your camera

Channel: AViPAS Inc.

Views: 1,276

Rating: 4.4285712 out of 5

Keywords:

Id: UfjlsUCnNts

Length: 8min 34sec (514 seconds)

Published: Fri Jan 08 2021