How to Replace Rear Wheel Hub Assembly 2012-2017 Toyota Camry

[Music] [Music] using a 19-millimeter socket go ahead and remove the lug nuts and take the wheel off and set that aside in a 17 millimeter deep socket i'm gonna go ahead and i'm gonna go ahead and remove this upper bolt here this lower one loose work that out and we're going to use the caliper hook here we're going to just remove this i'm going to go ahead and set this hook up on a spring we want to pull this up and get this out of the way so it doesn't fall go ahead and remove the brake rotor set that aside and there's four bolts on the back of the wheel hub there's one here one down below here and then there's two on the other side using a 14 millimeter socket we're going to go ahead and loosen these go ahead and get that one move to the other side [Music] go ahead and i'm gonna go ahead and remove these bolts now go ahead and remove all four of the wheel hub bolts and set these aside using a 10 millimeter socket we're going to remove this bolt here for the abs wire harness and there's one over here we're going to remove this is going to allow for some slack when we remove that hub [Music] and set these bolts aside using a hammer you can go ahead and work your way around the outer flange here to get this hub to come out as you separate this here you'll be able to see the abs connector in the back here all right using a pick and get into this little notch right here lift the connector out and disconnect that whole connector there i'm just going to go ahead and tuck the abs wire back through the knuckle there now we want to go ahead and separate the backing plate here from the hub itself so we put a couple of bolts through the back of the knuckle here and these have lock tight on them i'm going to go ahead and feed the backing plate on and push those studs through to get this lined up go ahead and put the other bolts through on the bottom get those lined up and now we're going to go ahead and line up the wheel hub making sure that the sensor lines up with the hole in the knuckle good put that in we're going to go ahead and reach around the back and see if we can catch a few threads in the wheel bearing all right using a 14 millimeter we're just going to go ahead and snug these up i'm going to go around to all four of those bolts this is going to pull that hub into the knuckle and in place i'm going to go ahead and go to the other one all right i'll go to the other side i'm going to install the abs bracket here gonna get the bolts started there bring the other one up and get that threaded onto the strut bracket with those started we can now go ahead and reach around the back and connect the abs wire and just take the abs connector line it up the sensor itself for the wheel it should slide right on press it until it clicks and there it is i'm going to go ahead and tighten down or torque these four hub bolts to 44 foot-pounds and do this for all four we're going to go ahead and tighten down these 10-millimeter bolts for the abs just gonna hold it back and just snug this down do the same for the strut bracket now we'll go ahead and put the brake rotor on make sure that your e-brake is adjusted next we're going to go ahead and remove the hook for the caliper bracket and the caliper line this up open up the pads a little bit and work the caliper onto the rotor and we're going to go ahead and get a bolt started into the upper caliper bracket once you get a few threads started go ahead and put the lower bolt in i'm going to go ahead and snug those down all right we're going to go ahead and talk down the caliper bracket to 58 foot-pounds and then we'll go to the upper one and do the same up top i'm going to go ahead and install the wheel and get all the lug nuts started by hand i'm going to go ahead and snug these and torque them to 76 foot-pounds and torque these to 76 foot-pounds [Applause] you

Channel: TRQ

Views: 8,457

Keywords: 2012, 2013, 2014, 2015, 2016, 2017, TRQ, Taillights, Toyota Camry, aftermarket part, car, car parts, car repair, diagnostics, diy, headlights, how to install rear wheel hub assembly Toyota Camry, how to replace rear wheel hub assembly Toyota Camry, rear wheel hub assembly, regulators, repairs, shocks, shocks and struts, strut, strut assembly, trqautoparts

Id: 6jIUf6-6ISs

Length: 10min 37sec (637 seconds)

Published: Mon Dec 06 2021