Hello! I decided to make a video about How can I do, at home, Without special equipment, And expensive tools, Here is such a crossbow, Pistol type. This weapon is notable for its simplicity, Reliability, noiselessness, As well as cheap shot. Since bolts, crossbow, self-made, Can serve, literally for years, And survive thousands of shots, If certainly, they are correctly made, And the target is, adequate strength, tip. Look further, that for this purpose it is required, And how I did it all. This is a piece of a two-handed saw, Or as it was called, Drank Friendship. It was designed for sawing large logs. This is carbon steel. I've done some markup, And now I'll cut it, I need to get off of it, three lanes. With the help of a depth gauge, I put out exactly three centimeters Here is this plate, it serves two purposes, This is the first: that it was an accurate, even line, Another: this is what partially absorbs heat, Which is produced when cutting a Bulgarian. Also, you can not detain a Bulgarian, at one place. Because, it will lead to a scorching, And the release of steel, And it will lose its elasticity. All three strips, I clamped on clerical clamps, So that everything is tightly held Before that, of course, I put on a flat surface And fixed. Now, I will hold, turning this business, On the electro-grindstone, Ie, I trim a little, So that everything was perfect, smooth. Plates electro-sharpener, I perfectly leveled. Everything turned out, quite smoothly, I checked it, the shank-caliper The next thing I do, I took a diamond natfil, And they, here this sharp edge, I will clean, Because, it can be injured, In the process, further processing. And so, I'll do, absolutely, with all the plates. All three plates, I cleaned it completely with emery, I removed all the rust that was. And I conducted the test. I took the arc, and here in this way, Knee, tried, bent. You see, it turns out that, In the center, here is this part, bends well, And then, practically, it does not bend, It is understandable. The effect of the lever, all the same. And here, in order for the workflow of the Tetevs, Was the maximum You need to do a little turning, Ie, it turns out this way, At an angle to grind, so that the whole arc, Completely bent, and worked, Ie, a springing effect, was the maximum. For this, I waste these parts here Drill I have very little power, Therefore, I had to use two drills. One - on the tile, The second - for concrete. And both, excellently drilled, rolled steel. Now, I will deploy the whole thing, up to 8mm .. This bar, will serve as a crossbow of a crossbow, I understand that this tree, From hard rocks. I think those who understand the tree, Say in the comments, what is it? Vobschem then in the bar, I made a markup, And drilled a hole, Not through, of course, Diameter of 12mm. All this business, I warmed up, And processed, fresh epoxy, Ie, which has only been mixed with hardener. This is necessary in order that, it is well absorbed, And the strength, in this part, was the maximum. Later, in this hole, I pour epoxies, And I will insert, here this here, a part. This I think, as you found out, Those same nuts, Which, I grinded in a lathe, On the mandrel with thread, thread m8., This is a fixing screw, actually. Turned, I'm thus, for what, So that when he is immersed in an epoxy, It is as good as possible, Fixed these screws, And from the dynamic load, This business, could not go anywhere. I think it's understandable. Also, fatty grease, Here is such, I processed, the screw itself, So that epoxy, hitting the thread, Could not, to so much hard, to stick to it, That it will be unscrewed, just then, it will not work. And the nuts themselves, automatically, when they wind up, Too have turned out, fat from within. Even if there is an epoxy somewhere, it will flow, Stick well to them, it can not, That is, a screw, I can safely unscrew. Epoxy I use, The most common EAF. Inside, everything is well adhered. The surplus resin, which was here, I carefully, stole it with a knife. Epoxy was a bit stuck, Ie she was not, the freshest, But it was, quite fluid. I managed to unscrew the screw, literally, with my fingers, After all this business, has frozen, Probably for the same reason, That when he stood for a while, Then I, it all warmed up well. So that it freezes quickly. So now, I will do the following. Now I will make my aunts. I bought a stainless rope, Section 2mm. Here, at me as you have paid attention, There are special slits. These slots, are needed in order, That, the cable was held, Or, the future Tetev, as they say, on the spot. I inserted it, along the ruler, Looked 4.5cm., To the side accounted for, Well pressed: once curved, the second time curved, And I got two bends. I did it all with my hands. Further, I will turn this thing into two loops, From two sides. For gluing the cable, Rather its loops, I used a pvc glue, with the addition of hrompic. Here he lay on the tile, And already enough, well dried. That is, these parts, they have already become, completely dry, And I think it will be possible, When it completely cools down, Experience, and see, How to dress properly, such a thing, To the crossbow. A rope, dresses very simply. Here in these two grooves, Here, in this way, He clicks, once, Secondly, it turns over, And one shoulder, rests against the surface, And stretches his arm. Now it's time, Make, guide, for the arrow. She will be on top of the bed, Above it will pass, Tetev. This, the aluminum corner, And it, I vobschem then now, I will bring to the condition. Instead, you can use, For example: a metal corner, or a skewer. That's the way here, curved. Aluminum corner, Which will serve as a guide for the arrow, I stuck, on epoxy, In the very groove that he did, Here this chisel, Or more, you can call it, stylist. Now it will freeze, I'm at this time, take care, the handle. I bought it on the market, Literally there, for 40 cents, in my opinion. It is made, with durali, And she really liked me, And it cost, it turns out, a penny. Handle, I polished. This furrow, from inside the frieze, I did what for, So that when the epoxy is filled, And it will harden, it is very firmly held This part, could not jump out, Together with the fixing screw. Now I'm all this business, I'll pour epoxy, Pieces of fiberglass, I'm a punch, I made a hole. I'm dealing with this, I'll put it on the screw, So that everything is very solid, it was later. Now screw, I have a glue, for super-glue. I just put it out, That he, ideally exactly, was coming from all sides, Ie when I screw in the handle, So that there was no backlash, No zaidany any, That was all very smooth. This deepening, will serve, in order, So that he could go to the Tetev. After that, it will be pushed out, And will move, and move in front of him, the bolt. So, I still did that, I, after I have moved, I processed it with a file. Ie, as if a little rounded here, What would be the maximum, the area of resistance. This I, in a consequence, I will treat with epoxy fresh, So that it all absorbed. I will wipe out the excess, and it will freeze with me. Here is this part, I processed a flat rasp. Drilled a hole for the handle, Vobschem then, here, here in this part, I did, just like in this, And poured epoxy. There the nuts are turned so, So that you can turn the handle. Here, by the way, not only did the screw itself cover, In fatty grease, But also this lower part so, That, it was possible to unscrew, Although I did not calculate, Epoxy sdes turned out too much, And she protruded. She was a little stuck, But this problem, I decided this way. I took it, put it on, And the handle, the hammer itself, Tapping lightly, twisting, This is the whole thing put forward, And unwound normally, in general. Now, you can say, it's a removable handle, Which I think will be very convenient, in transportation. Ie, you separate it, and carry it all, in a package. So this thing, pasted up This, two layers of fabric, Processed pva, with hrompikom. It will serve to extinguish, Dynamic loads, But this is not even the main plane, Here is the most important, this washer. I made it from steel 45, And vobschem then sdes, I pasted too, Two layers of this fabric, Pre-punched, punch, hole. Two layers of nada, So that when the shoulders, during the shot, straighten, They seem to go a little forward by inertia. And every time, they will make a hit. And what would this blow, extinguished, Here, this thing is needed. This can be replaced by black rubber, From the cameras, for example. Instead of cloth soaked in pva, If you do not want to mess around, And rubber you do not have a black, normal, so dense, Then fit, even perfectly, the skin. Ie, a good, thick skin, From the belt for example, is ideal, For what would be amortized, overload, When shot, Or rather, after it. That's all. The handle is twisted, it seems to stop in this position. I think it will be very convenient, it's all in use. At the aunty, I wound up, fishing line, about 1mm. In diameter. This is necessary in order to have a cable, Well and slid easily, along the guide, As well as not too much, Stuck, here in this, here's the part of the trigger. So did I, the trigger, Which is very easy to work with. He, just pushes out, from here this one, here are the pieces, The very aunt, and she flies in front, Pushing forward, bolt. Here, on the edges, I have blotted, Here this loop, And the second, too, Glue pva, with hrompikom, For demonstration, shock loading, Which is present, in this part, when shot. You see, it's all splattered, Ie, the cable, is experiencing very, very large loads, In this part, and here it is, He can, tear. Therefore, it is desirable to dress, Pvc tube, I forgot to do it, At the very beginning, when making a noose, But if something happens to this, Or I will do, a new aunty, Then I necessarily, thin, pvh tube I will dress, from a dropper here, And here, just like that, So that the cable is not cut. The trigger is very, very simple, like I said. It's a piece of aluminum, Stripes of aluminum, cut, And inserted, In the groove, Which I did, With help, drill, And a four-feather cutter. Before that, of course, I did, A hole in the beginning and the end. I drilled here, two holes, Where now, the pusher is With the help of a drilling machine, Ie on through, and it was me, an excellent reference point, In the second, it turns out, Excellent vertical, at 90 degrees, as they say. This is a piece of that same, aluminum strip, With which I cut, trigger, That is, I cut off a piece, Then a hacksaw, once made an incision, Second incision, And here, just as he carved, And here, such here, the figure turned out. Oriented, naturally, already by the existing deepening, In this one thing, Sdes, I think it's clear, As it is established, the spring-pusher, Which returns, the trigger, In the starting position, And hairpin, On which it rotates. Spring, you can not put, Ie it is clear here that, When laying the awning, Here in this thing, Trigger, automatic, bend down, And vobschem then, go down to the right position. But, I decided to do it like this, As you see, also, there is no super-high accuracy here, Yes it is not required. Why, because the play here is big enough. He is quietly walking to himself, And efforts on it are not too big. Accuracy in such a node, do not need high, That is, the spring is taken from an ordinary ballpoint pen. Everything is processed inside, And near, this very place, Epoxy resin. Also, here is this nest, Also treated, epoxy, Heated, and fresh epoxy coated. It is necessary, to increase strength, and wear resistance. By the way, the aluminum guide, Here this corner, Was polished on top, small nazhdachkoy, So. So that the aunts do not feel strong friction. I drove the axle. This is a piece, 3mm. Rod, Holes, by the way, also 3mm. This, a pvc pipe, Exactly the same, are used in droppers, You can buy at any pharmacy. I cut off a piece, And its length was cut He took off the cable, Put on one loop, And another loop, just put it on. Now it will be, an excellent blowout, So that the cable does not erupt. If these things are worn out, They are very easy, you can replace them. When I already had a crossbow, With an arc, glass-plastic. I have disassembled it, in general, for spare parts, Because of uselessness. And left of it, Self-made bolts. Their caliber is 6mm. And now, it will be necessary, Here to do, Special spring, Arc-shaped such, To hold the bolt, so that in any position, Shot, it was possible to produce, And just so, bolt, could not fall out. I forgot to mention. The shank of the handle, this part, I had to prune, Because, as you have noticed, it is twisted, And this part interfered with the trigger, Because I had to remove. Tree, I also have to, it's probably cut a piece, So that everything is neat, and aesthetic. Here, I vobschem then made a spring, to hold the bolt. It is made of skewers, Which I snapped Bent it in a vice, with the help of a hammer, Drilled holes, under the cog, And in general that turned out, here such design. In the most wooden part, I did, with the help of a file, Groove, so that he would clearly sit in his place. On the arc, I would like to say the following. Steel, is used here, millimeter, And in general, the force of tension, such that it can be loaded with hands. This crossbow is more intended for entertaining shooting, Rather than, for hunting, or fishing. If someone wants to do something, Hunting crossbow, Then, it will be necessary here, another couple of steel plates to insert, Not even the full length, but somewhere, To reach, to the middle, one arc, Half arc That is, somewhere, up to here, And up here, And this is very strong, will increase the power. Now, I think, there is a reason, Test, tension force, With the help of an ordinary canter, a household. The tension force is 13 kg. It will be for me, absolutely, enough. And if it's not enough, then I always, can strengthen it. The first test, Or as you might say, a test, I decided to do it right here. Distance to the target, where it is half a meter. This is a set of corrugated cardboard plates. Here, the tips of the arrows are visible, four pieces. The number of sheets is punched, One, two, three, four, five, six, seven, eight Eight sheets, corrugated cardboard, punched. However, it's pretty, good result, I think so. A sheet of gypsum board, 10mm thick. The probit is through. There it is, two pins of plastic, And on them, hung on a hairpin, Two packages, eight layers, corrugated cardboard. Well, in general, I got it, Three hits, and once, I underestimated, And got into a pinoplast. Almost, you can say, through, That is, there are, the tips stick out arrows, That is, I think it's normal. I'll shoot, from the same distance, But, I put the camera closer, And put a little closer. I got the arrows. Those who have got into the pinoplast, Left, on the most, shank, Ie, at ten centimeters, penetrated, inside the pinnoplast. Now I'll do it, I'll still wrap up the series. You see, I'm a little used, And now, at me it turns out, to shoot more heap. When, even more firing, I think, There will be results much better. I decided to conduct an experiment, And now, I'll shoot, on a tin can, And gas-concrete block Shoot on bottles, with such a thing, I do not advise Here the tips are made of raw steel, not hardened, And they are a little wrinkled, Well, it's nothing. In the future, I trim them. I think everyone noticed, That the crossbow, worked, just flawlessly, Ie, there was not a single delay, Not a single misfire, As happens with the flocker cartridges It, in general, and it is understandable, Sdes incendiary composition, Which, with time, can dampen, Or just cake up. The same thing, She, absolutely, trouble-free, Very, very reliable, in other words, you can say, And in general that, still I want, from myself to add, That these are these bolts They were, under another crossbow, Faster, and less powerful than this developed And, of course, that under this crossbow, You need to make arrows, Much, heavier, A greater calliper, for example: eight, seven millimeters, With a longer point, Ie, a heavier one, and a longer shaft, So that, the power of the arc itself, More went to the bolt, But did not load the cable. However, because of this, and there was such a thing, not a pleasant one, Like a crack, here sdes, not big, But I will eliminate it. You, I advise you to use, not the glue of the pva, But rubber glue. It will be, the best, And make a winding, much longer, Ie, still here, a centimeter, two add, Then, the reliability will be at all, the spike. Also, I want to thank all those, Who has waited, this video. Because, the first comments, With a request, make a video, about a crossbow, In the home, Even more, six months ago. So, here, in general, it came out. Thank you for your attention! Who liked the video, Do not forget, put your finger up, As well as, share the video, subscribe to the channel, There will be a lot of interesting, and useful! GOOD LUCK TO ALL!!!
