How I Add Refrigerant to an Air Conditioner

hey hvac techs i'm craig fox and today we're going to talk about adding more refrigerant to an air conditioner i wanted to expand on our recent troubleshooting series by going into each part of its sequence of operation this week it's the refrigerant let's go over to some of the basics to charging an air conditioner on your average 90 degree day in the middle of summer upon arrival at the house your customer tells you that the air conditioner worked just fine last year but this year the system seems to be running non-stop especially as the summer days get hotter and hotter you ask the customer have any other technicians been out to make repairs on the system lately and it's very likely the customer will say no there's a lot of things that can affect the refrigerant charge just remember for the sake of time we're trying to keep this dialogue short so that we can get to the point of charging the system up i like what brian orr from hvac school mentioned in an article i read he said we need to set up the equipment so that it won't freeze during normal operating conditions at the very least the typical residential ac system should be set up so that the return air temperature can get all the way down to 68 degrees and still be just above freezing at the evaporator coil let's say it's 78 degrees in a house on a 410a system and your suction pressure is 108 psi that means that your suction saturation coil temperature is 35 degrees so the coil won't freeze however the coil temperature will drop approximately one degree for every degree the return air temperature drops remember at 78 degrees inside the evaporator coil was 35 degrees so if the customer sets it down to 74 degrees the saturation temperature would get all the way down to 31 degrees and the system will start to freeze up knowing this let's grab your temperature probe and check the return air and the supply air here you notice the difference between the two is about eight degrees as a tech you know that the temperature split should be around 18 to 22 degrees next let's head out to the outdoor unit to feel if the suction line is cold now there is some validity to the old term beer can cold but it should not be the measure that you go by to check the refrigerant charge it can however give you a clue as to how the condition of the system is running now i'm not always a huge proponent of hooking gauges up to a system every time i go out to diagnose a problem but in this case we can tell that there's something not right with the cooling system so in this case i want to see what's going on inside of it hook your hoses up to the liquid and suction lines be careful of blow back too you don't want to freeze your hands follow all the safety precautions you've ever learned now what do you see on the suction side i like my text to talk to me about the evaporator coil temperature and the temperature of the condenser coil when i'm on the phone trying to help a tech out in the field it's hard for me to remember all the pressure temperature ratios between the different refrigerants that we use so if someone tells me that the evaporator coil is 40 degrees i can immediately tell that the coil is not freezing if someone tells me that the temperature of the condenser coil is 140 degrees i can immediately translate that to an outdoor coil that is under some seriously high pressures on the refrigerant gauge the outer circle and those numbers are the pressures the inner ring of the numbers reflects the temperature this is how i want my text to communicate pressures to each other it's just more efficient that way most gauges these days have a green ring for r22 and a pink ring for r410 the pink rings numbers are what we're using for the evap and condenser coil temperatures on a 410 system here we see that the evaporator coil is about 20 degrees for proper refrigerant levels the image that i want you to project in your mind is this our end goal here is to have liquid refrigerant reach all the way to the txv at the evaporator coil to meter the refrigerant appropriately right now there's not enough liquid into the system to do that this means that vapor is making its way to the metering device and we're not giving the coil enough refrigerant to interact with the speed of the blower air moving across it we need the perfect balance of air flow and refrigerant pressures to create that 18 to 22 degree temperature split that we're looking for let's suppose that the system holds 10 pounds of r410a now in my mind i'm thinking the system is about halfway charged from what we've seen so far it's an approximation but we have to let the customer know about how many pounds that we're wanting to add so that they can give you the okay to move forward of course you don't know for sure how much it is but they should be aware that it could be around five pounds we need to let them know that it could be a couple pounds more or it could be a couple pounds less but either way we need permission to move forward using a scale is the only way that we know for sure how many pounds of refrigerant that we're adding and it's cool to let the customer know that you'll be using this too it's reassuring for them this is also great in preventing you from over charging the system too okay so my service hoses are already hooked up i'm going to start by putting my charging hose onto the tank of the refrigerant next i open the refrigerant tank valve and place it upside down on the scale with the gauges closed on the manifold i crack open the connection where the charging hose meets the manifold not too much though we just want to get the refrigerant to prime itself up to that point so that we can get rid of any excess moisture or air in the hoses reset the scale back to zero so that we know how much we are adding as the refrigerant enters the system i recommend that you put an amp clamp on one of the wires leading to the compressor too if you've seen my videos on diagnosing a bad compressor you know that the compressor's amp draws correlates with the refrigerant pressures inside the system the healthiest compressors will run at around 60 percent of its rla when you're charging up the system you'll see amp draws fluctuate as the refrigerant goes in and settles down use your knowledge about the compressor amp draws to monitor your charging process okay we're ready to charge with the charging hose valve open we'll start opening the suction side valve a quarter to a half a turn is enough there's no approximate amount of time it'll take to insert one pound of refrigerant each situation is different to know for sure use your scale in this situation where we think the system is about four to five pounds low let about two pounds flow into the system and wait for five to ten minutes for the system to equalize question how long does it take for the refrigerant to cycle through a typical residential split system i'd say about three or four minutes if you have a different answer let me know in the comments down below so we see now that the low side has come up to about 27 degrees or 92 psi our evaporator coil is still freezing let's add two more pounds and wait i know there's a lot of pressure on techs to get their calls done quickly so that they can get on to the next one but it's essential to let the system stabilize before adding too much refrigerant if you add too much too soon you could see the pressures skyrocket insanely fast and now you have to recover some more refrigerant into a separate tank which takes even more time okay now we're getting close to 32 degrees or about 100 psi on the suction side from here we want to start dialing in our sub cool to whatever it is that the manufacturer recommends this system says 10 degrees sub cooling on a 95 degree day let's get a temperature probe on the liquid line start getting our reading from it we're going to be subtracting the high sides temperature and the liquid lines temperature to come up with our sub cooling add refrigerant a little at a time until the difference between those two numbers is 10 degrees just don't add too much too fast add refrigerant and wait for the numbers to stabilize you're going to be looking for the low side pressures ultimately to come around 40 to 42 degrees or 125 psi the high side pressure temperatures will likely settle around 15 degrees above the outdoor temperature so on a 90 degree day you may end up with a high side temperature around 105 degrees if you can get your numbers around this area you're close but let's really get it dialed in and get that sub cool to 10 plus or minus 2 degrees i will tell you it takes longer to move the needle on your gauges when there's less refrigerant in the system as the system starts getting close to proper sub cool you'll want to finesse the time that you keep the manifold open allowing refrigerant into the system over charging can happen quickly especially on a hot day getting close to your 10 degree sub cool cool once you get it to this point check your temperature split inside is it around 18 or 22 degrees great you'll notice that the liquid line is a little bit warmer than the outdoor temperature also the suction line will be damn near beer can cold test the system while it's running get your amp draws on the condenser fan and the compressor motor cycle the system on and off of the thermostat to make sure the system is operating correctly and if it is you're good to go well i hope this has helped you when it comes to the charging process i make my videos for my technicians to reference when they're out there in the field and they're in a bind but if this can help anybody else that's great if this is your first time watching our channel please click subscribe down here on the bottom right and if you click that little bell next to it you'll be notified of all of our videos as they come out thanks so much for watching and we'll see you on the next video you're watching fox family heating and air don't forget to subscribe and check out more of our videos by clicking on the right side of the screen you

Channel: Fox Family Heating and Air Conditioning

Views: 354,393

Keywords: How I Add Refrigerant, how to add refrigerant to air conditioner, how to add freon to air conditioner, how to add refrigerant to ac, how to add refrigerant to home ac, how to add r22 to air conditioner, how to add r22, how to charge r22 unit, how to refill ac charge, ac unit low on charge, ac low on refrigerant, air conditioner low on freon, how do I add refrigerant, how do I, freon, r-22, r22, r-410a, r410a, r410, 410, 410a, puron, air conditioner, heat pump, Fox Family Heating and Air

Id: plTCLJF_zQk

Length: 10min 19sec (619 seconds)

Published: Fri Mar 19 2021