GLOW EFFECT explained in 5 minutes

if you have clicked on this video congratulations you are gonna learn how to paint glow effect like this or this and you are gonna learn in just under five minutes so let's do this okay so the idea for this video came up when I posted this photo on my instagram and as far as you can see quite many people liked it and asked me how to do this now I have done this in just 30 minutes and honestly it was just an experiment anyway the recipe is quite simple and if I had to describe it in just one sentence you paint the whole light source with white and glaze over it with whatever paint you want most likely some blue orange pink or green but but for it to look really good you have to go a little further than that so let's start with painting the light source with pure white paint now if I'm not painting my sons of the phoenix space marines I usually start off with black spray so as you can already guess it will take you multiple white layers to cover the light source properly and while each individual layer cannot be super thick otherwise you will get miniature like this it cannot be super thin transparent layer either I cannot really tell you how much water you should add to your paint since every paint brand will need a different amount but it should take you about three layers so just aim for that when you get a nicely covered source of the glow it is time to think about what is the single brightest spot on this light source in a case of this marvel crisis protocol Hela miniature the whole orb thing or whatever that thing is is the source of light and as such the middle part should be the brightest and you should leave it mostly white in a case of the plasma weapon for warhammer it should make sense for the light source to be inside of the gun and as such we will treat bottom of the coils as the light source of course you might treat the top of the plasma coils as the light source and you should get results like this but I guess it depends if the weapon is prepared to fire or not but I don't know either way once you know what is the brightest spot on your light source you should glaze all of your layers towards it there is no definite consensus whether you should start off with dark glazes or light ones instead but honestly you will have to go back and forth between the two anyway I am starting off here really dark with glaze of Khorne red once again I do not have exact ratio of paint and water but if you are not sure apply thinner layer and wait for it to dry and apply another one over that it is way better to proceed slowly here once I got it I can take Vallejo model color vermillion red or any other quite vibrant red paint and apply another glaze aiming towards the light source since it is something between glaze and wash I let it spill over the recesses here since that is where the light source is in fact the recess itself is the light source with pure vermillion red I have covered still quite broad surface but now I will progressively add ivory to the paint and cover less and less surface with really controlled glazes of course the more ivory you add the less surface you will cover with the center of the light source being the brightest if you are not sure whether any part is too dark or too bright you can simply take a picture and apply black and white filter over that if you are still not happy with what you get decide which part should be brighter or darker and apply thin glaze of corresponding paint over such spot now getting back to Hela you can see that the same applies here the center of the light source is really bright and light and the further you go the darker it gets okay we got the light source itself BUT WAIT, there is more to really sell the glow effect you need some additional reflections so what we are gonna do here is that all around the light source we are gonna paint some more dim light now don't pick the brightest paint that you have since only the light source should be as bright but you should pick some of the mid-tones for the plasma you should mostly use pure vermilion red and you might combine it with a little bit of corn red for the darker parts and just a little tiny bit of ivory for the parts that are near the light source I am taking this vermilion red with corn red and just lightly glazing all the area that is supposed to be exposed to the light source mainly the shoulder pad and the area around the plasma coils the closer I get to the plasma coils the lighter the paint I use is use here even thinner glazes since you want to build up this dim light without having any hard separation in the case of Hela from marvel crisis protocol I use mainly Moot green combined with dark green and combined with white for those parts that are really exposed to the light source keep in mind that in every case the edges should be exposed to the light source the most so you can almost highlight them with the brightest layer that you have dedicated for the dim light but once again be reminded that this layer has to be less intense than the light source itself okay so I think that this covers it before I go I just want to mention that it is way easier to build up this dim light on darker surfaces or at the very least for me it is and that is because i find it much more easier to build there some nice volume for example on pure white surface I find it really difficult to build up and I don't even mention that you are gonna have a hard time creating contrast between the white and the light source okay so that's the video if I have missed anything or if you have any sort of feedback go ahead and leave it down in the comment section of course if you want to see more content like this go ahead and subscribe to this channel and if you want to help others get better at painting miniatures go ahead and give this video a thumbs up because that way youtube will know that it should take this video and recommend it to them and see you guys in the next video bye

Channel: Zumikito Miniatures

Views: 196,360

Keywords: paint glow effect, glow effect, glow effect warhammer, glow effect warhammer 40k, painting plasma gun, painting plasma weapons, painting plasma coils, painting object source, painting osl on miniatures, painting osl effects, painting osl 40k, painting warhammer 40k, painting warhammer, painting light, painting light source miniatures, object source lighting, warhammer, marvel crisis protocol, painting marvel crisis protocol, painting plasma glow, Hela Marvel Crisis Protocol

Id: lGxjc7cdwms

Length: 5min 15sec (315 seconds)

Published: Fri Sep 04 2020