Gas are no longer necessary! MULTI-FUEL BURNER from pipe for heating.

Video Statistics and Information

Video
Captions Word Cloud
Reddit Comments
Captions
guys today experiment i have something to show  you homemade is very simple but at the same time   very curious and necessary you can save food for  thought and it will prompt many to their ideas   hello friends all components can be found  everywhere shops old unnecessary scraps etc   i'll start with the copper tube the tube is six  millimeters in external diameter and approximately   two meters long with a mandrel for it i took a  piece of pipe from a water supply system of 32   millimeters i did about 12 to 13 turns optimally  10 turns i have a whole collection of nozzles from   the smallest to over a millimeter bought from  a welding shop i will choose exactly what you   need by experience they do not have the same  thread the pitch is different this is how the   spring from the tube turned out the nozzle  will be at the end of the tube around here   i will cut off the tube and bend it so  that the nozzle is in the center of the   diameter of the coils to be able to replace the  nozzle it will be twisted along the m6 thread   the thread and copper is cut easily i will select  the desired diameter of the nozzle and later i   will seal it with sealant or tape i bent the tube  very carefully and carefully so as not to break it   train on small unnecessary pieces everything  turned out very well as i wanted and with a   small margin welding thin brass and thin copper  proved difficult but possible look here it is its   own man's little country this is my a workshop it  is almost ready and i will show it from the inside   soon the workshop will have combined heating  we have frosts even my beast freezes quickly i picked up several options as a container a  piece of pipe an empty gas cylinder and even   a square pipe i promise to give a review  about the angle grinder the battery angle   grinder is simply amazing now this is my  favorite instrument link in description   there will be two holes in the profile  on the sides i cut a one-quarter inch   thread with a tap from below there will be an  exit and from above under a small pressure gauge   the pressure gauge is only for testing i want  to see what pressure will be inside or not   there will be three millimeters metal plugs at  the top and bottom a piece of threaded pipe will   become the neck of the tank the entrance  will be closed with a brass plug with an   oil resistant gasket to make everything neat i  process the blanks on the tape before welding   i also clean up the threaded trim i want  to install a valve to regulate and stop   work from two different taps i assembled one  on one side with a one-quarter inch thread   and on the other a fitting for a hose i welded  a copper tube to the fitting it would be easier   to solder the connection will be through  a one-quarter to one-half plumbing adapt you could just screw it in using a high  temperature sealant i prepared everything   before welding and began to ld input and output  connectors i really enjoy my cold welding machine   but i will also need a semi-automatic welding  machine the video has already been posted on   the channel in general sometimes you need to rest  and relax from work and hobbies the final stage   of assembly i paint with high temperature paint  up to 600 degrees celsius the tank lid will be   a regular plumbing plug oil resistant rubber  gasket all i smear with an anaerobic sealant   it is applicable to both drinking water  and gases liquefied gases and anti-freezes   the pressure gauge is only for experience to  find out what pressure is in the fuel tank   finishing the assembly and will test i will  test on refined gasoline he doesn't give a   fuss i wonder if it will work on oil and diesel  fuel trials it's minus 25 degrees celsius outside   quick start with preheat but it doesn't  work as planned but i don't give up i went   to the premises and replaced the nozzle i also  adjusted the position of the nozzle in relation   to the center of the coil and the depth of the  location this burner fries like an infernal rocket   works on slopes according to my feelings the  approximate power is 20 kilowatts i'll go outside   there is a strong wind adjusting the flame with  a tap does not work only a complete shutdown   the pressure gauge showed that the  pressure inside the tank is very small   but i will put the pump in the tank later  stopped by a crane but it does not happen   quickly can be used as a burner in the furnace  or boiler use as an outdoor or camping stove   the application is limited only by the imagination  friends who like the idea like subscribe   comment i will try to release a new  interesting video as soon as possible   health and peace to you and your loved ones thanks  for watching this video see you soon friends
Info
Channel: Mr. Robo
Views: 1,995,813
Rating: undefined out of 5
Keywords: diy, craft, tools, how to make, homemade, gas stove, petrol stove, oil stove, stove camping, camping stove, camping, camp stove, firestove, stove, best stove, oil burning, camping stove portable, wood stove, wood stoves, gasoline burning, stove tips, heating, gas, gasoline stove, gasoline
Id: _5FsUfavNVw
Channel Id: undefined
Length: 5min 39sec (339 seconds)
Published: Fri Mar 25 2022
Related Videos
Note
Please note that this website is currently a work in progress! Lots of interesting data and statistics to come.