FlipMods Elite General Overview for Flipper Zero

Video Statistics and Information

Video
Captions Word Cloud
Reddit Comments
Captions
hello this video is just going to be a general rundown of the flip mods Elite board this compared to the ultra has an external antenna for the sp32 has a GPS which has a wire leading to the back where it has an active antenna it also has a switch on the side right you can switch between the eight pin or this is the eight pin down is eight pin up is esp32 GPS so these two will be powered on or off I know I have a video on how to use it with how to update the esp32 with ESP flasher but that ESP 3 or the ESP flasher firmware that's included will not be it won't run the best with this because the GPS pinout is different on that firmware so I'm going be making a video on how to update it using the SD card so to start off with what the package will come with it'll come with these three antennas this antenna is a 433 MHz which is used with this board this is a 2.4 GH these are both 2.4 this is just a higher gain antenna which I recommend to use with the sp32 so I recommend this one with this nrf24 board but you could swap the two just keep in mind don't use any components that don't have the antenna plugged in especially the cc101 please do not use this board plugged in without this antenna plugged in and also don't use any of the 2.4 GHz antennas with this and vice versa don't use use this 433 with the other two antennas board will come just like this what we're going to do first is make sure your flipper Z off and plug in the board all right now depending on what we're going to do first we're going to do the esp32 so make sure it's switched on so even though the board is on I'm going to screw it on but don't use the application that's taking advantage of the board without the antenna plugged in so right now I have the High Gain antenna plugged in and we're going to go to the application so right now I'm on uh extreme the Lays version of extreme so this is how the layout looks like going to go to apps I have I decided to put all the files that I use my boards on into one folder but I'm going to do it as if you guys didn't do that so we're going to go to Wi-Fi which is all the way at the bottom just going to show you guys and then go to Wi-Fi Marauder so evil portal is now in Wi-Fi Marauder so don't use the individual application just use Wi-Fi Marauder to do evil portal because it won't work it's not this wife or this evil portal application will not work with the firmware that's included and then there's going to be an option that says save to flipper SD card and we're going to click no because this is asking to save to The Flipper Z SD card we don't want it to save it through there so we're just going to click no save logs to The Flipper zero SD card no so we're good now we're going to do a scan test I'm going to blur this stuff out but we are scanning a bunch of information right now perfect now I'm not showing you guys how to do any tax anything like that there's other YouTubers that could help with that I'm my purpose of making this video is just to show you which applications to use with what but I will show you with evil portal I already included a just a basic HTML called Elite uh here it's just going to make a little portal that I could connect to on a device and it's going to prompt me to put a username and password once I do it'll just uh save it to a log and uh it'll also pop up on the Clippers Z the final thing is this GPS so right now you can see it's a consistent red light when it does capture satellites or not capture but when it has a lock on satellites this red LD will start flashing right now as you can see it's not flashing and that's because I'm indoors and I don't have a good view of the satellites also this antenna is just pointing straight down if you want to get a lock on a satellite you have to be you know it's preferred to be outdoors where there's nothing blocking the view of the the antenna I'm going to go try to get it lock right now by just going outside and getting it to uh you know show like my coordinates so right here you can see it's flashing now you can do War Drive but I'm just going to show you GPS data well I'm going to blur this out but it shows a date longitude altitude you could go up shows you how many satellites all right I'm back inside but yeah as you can see it stopped flashing because I'm indoors lost all the satellites but the way I was able to do it was just constantly moving it while this was pointing up to the sky like this in a circular motion probably took around like 2 minutes but if it's taken too long try turning it off and turning it on or you just get in a better position more exposure yeah now that we're done the sp32 turn off the flipper zero switch it to eight pin and now and test out the NF nrf24 and the cc11 right here here uh well this you could probably find this on my shop it's this a little 8 Pin 2x4 pin protector like I said 2.4 GH and just screw it in plug it in it's going to look like that you could also unscrew this we don't need it anymore it's not an issue if you keep it on but we're just going to screw it adjust so we could focus on this all right now we have nrf24 plugged in we're going to go to gpio in apps and then we're going to keep going down until we see nrf24 sniffer launch that just as a test lower the sample time as we can see address rate is increasing so that's good and then we could also test Mouse Jacker it's probably not going to work just like that way you fix that is you just either unplug the nrf24 restart the flip zero go back to it 24 Mouse Jacker I just put a test file in there there you go then you could select one of your scripts and that works now is a cc 1101 so just to be safe let's just turn off the flipper zero take out the NF 24 remember don't use any of these components without their antennas plug it in still make sure it's set to eight pin turn it on right here we go sub Giger and then the way you set it up so it uses this external board is you go down to radio settings and make sure external is set on this internal external swapping will only show up if it detects that there's a board so it detects that there's a board so that's why it lets me switch to external then you could just redraw and I'll bring a controller as a test I'll be right back so I brought this uh ceiling fan controller it operates at around 304 MHz which isn't the within the effective range it will detect it but the effective range is around the 400 MHz range just as a test as you can see we got all three presses stop it go back also so we're going to turn this off when you want to unplug or plug in the SD card make sure it's the flipper Zer is turned off and you could unplug it or keep it plugged in but like I said just make sure there's no power going into this thing there you go if you have a micro SD card reader like to usba or USBC you could use that just plug it in look at the logs uh mess with the app.config mess with the end index.html I'll show you more about those in the next video but this video was just a general tutorial how to use the elite board thank you for watching
Info
Channel: Sacred Antwon
Views: 12,473
Rating: undefined out of 5
Keywords:
Id: VrHoPaKbk-E
Channel Id: undefined
Length: 9min 40sec (580 seconds)
Published: Tue Jan 30 2024
Related Videos
Note
Please note that this website is currently a work in progress! Lots of interesting data and statistics to come.