esp8266 wifi module-How to update esp8266 Firmware/Software Arduino, esp8266 Flasher, AT commands

so offense this is the ESP a to double six Wi-Fi module which is most commonly used throughout the world for automation purposes with the help of this module which is ESP a to double six you can control and monitor any electrical device it may be above a motor robot cord sector etc etc you can monitor your sensors wirelessly from anywhere around the world in simple words we can say that this tiny module which is ESP a to double six has infinite uses it can be used in millions and billions of projects and different styles so before we started using this Wi-Fi module in any project first with me tell you about it's been also starting with this pin this is the VCC and it should be connected with 3.3 volts of the arduino or omega so make sure that you don't apply which is greater than 3.3 wolf as it can damage this Wi-Fi module then this second one is the reset and this one is the siege and the score of PD and this one is the TX which is a transmit pin of the Wi-Fi module then this one is the ground and it should be connected with the ground pin of the Arduino or Omega and this one is the GPIO one and this is the GPIO zero and this is the RX receive Minh of the Wi-Fi module so normal friends that you have an idea about its pins and now before you can use this in a project first of all we have to update a software so so how to do that actually now first of all as you can see on the screen first of all upload this simple sketch which consists of the white setup and the wide loop and as you can see the goal is just uploaded superfriends now to update the program we have to make some connections and that we will have to connect the TX pin of the Wi-Fi module with the TX of the Arduino and the aurochs of the Wi-Fi module with the RX of the arena connect the rst of the arduino with the ground as you can see so it will actually bypass the 80 magnitude microcontroller and then connect the VCC which is the 3.3 wolfmann of the Wi-Fi module with the 3.3 world of the arduino and also connect the PD pin of the web Wi-Fi module which is this one the CH and the spore PD can also connect this one with 3.3 world of the Arduino and connect the ground of the Wi-Fi module with the ground of the Arduino so we make these connections and make sure that you connect the GPIO pin of the Wi-Fi module which is this one the GPIO 0 with the ground of the Arduino so these are the connections and now let's update the software I have already downloaded that software so make sure that you don't work this software which is the the esp8266 on this the XZ file click on the pin and now select this one the we zero point nine point two point four 284 via so open this and my Arduino is installed on comm 5 so click we're here and whew I want you can also confirm this from here tools and oh here you can see it's come 5 ok so now click on the download I know you can see it's just started and what you can also see that the LED is blinking you so at 99 you will get an her but just don't worry about this okay so now the the formula is updated and now let's check the 80 commands so for that first of all we'll have to remove Audrina you know just disconnect that and disconnect the gpio zero so the word which is connected with the gpio zero simply disconnect this okay so now it's disconnected okay so now connect this okay and now click on the serial monitor so once again I want to tell you that make sure that you disconnect the GPI u.s. European from the ground so I order disconnected that and rest of the wire or ACM it says so the the dc-8 underscore PDS connected with 3.3 volt visas is connected with 3.3 world and the Rx is connected with the rx pin of the Arduino and the TX of the Wi-Fi module is going to hjx of the Arduino and the rst of the Arduino is going to give away the ground so now the serial monitor is open and let's type a command which is the 80 and 80 plus RS T so it's working great so now we are done with the with the software updating and as you can see on the screen the 80 commands are working so now this Wi-Fi module is ready and it can be used in any project I hope you like today's episode and like and share my videos with your friends and see you in the next episode and their upcoming tutorials all be making so many cool projects using this Wi-Fi module so do subscribe my channel so that you never miss any of my upcoming tutorials see you next episode

Channel: Electronic Clinic

Views: 34,020

Keywords: esp8266, esp, wifi module, firmware, update, iot, arduino, download, at commands, esp8266 arduino, ESP8266 WiFi module firmware update, esp8266 arduino at commands, arduino esp8266 firmaware update, esp8266 flasher, how to update esp8266 firmware, esp8266 firmaware update, how to download and update esp8266 firmware, how to update esp8266 firmware using arduino, esp8266 arduino flasher, arduino project, diy, wifi, electroic clinic, arduino projects for beginners, arduino uno, electronics

Id: yla44_KZ7eo

Length: 6min 18sec (378 seconds)

Published: Thu Nov 15 2018