Hello Youtube friends. A few days ago I went to the junkyard to see if I could find something to make a video, to do a project and when I arrived I found that they had brought new things, because it is a permanent replacement and I found this mountain of electronic scrap, a pile of scrap It seemed good but huge, so I climbed up it and started looking for what I could find. Something caught my attention, among all the things there were, a kind of engine. I found this monstrosity that looked like a motor but had a somewhat strange terminal board, it had a 16-pin terminal board and there was also another 4-pin terminal board, so this motor is very very strange, very strange. So I grabbed it and asked the owner because the owner gives everything to me, I told him to donate it to science, to see what it was and I'm going to bring it so I can show it to you too. I connected three cables here, one of these four was ground, so the other three gave me to understand that it was three-phase. Apart from what I read here it is 380 volts. The thing is that I connected it to 220 volts but with a capacitor to make the third phase and the motor ran, but with a consumption of 20 amps, crazy , because 20 amps times 220 volts is more than 4 thousand watts, that is, That engine was crazy. It wouldn't be of any use to me so I was going to return it. If I wasn't going to use it, why did I want it? and unintentionally these two tips touched me, at one point I wanted to move the shaft and it was stuck, but if I let it go it becomes very light, I barely see it and I say: here we are! This is a magnetic motor, it has permanent magnets inside and as soon as you move it it is generating energy and that is why it sticks. so I say NO! I'm not going to return it. I started testing it and I'm going to make a handle to make it rotate. and it had a handle that I had already used in a previous video so with this I could spin it. so we're going to put it here so I can spin it. so good like everything I try with an engine. what do we do? Let's see if an LED turns on, I put an LED on it and I did just that and there was nothing left of the LED. It flashed and it was over, so I say, let's try it with something else. So I brought this LED board with 54 LEDs and connected it and look what happens just by moving the lever a little, just by letting it fall by gravity, look. I mean, and these work with 12 volts, I can hit it hard because I would burn them all, so I continue, we are going to try it with something else that won't burn. So I decided to try it with a 2 culé cooler. The best thing is that I put them here, I connected them in parallel and my surprise was great when just by turning it a little bit like that with a finger they worked just by dropping it. Look, obviously I was very happy. We added a small group of more than 2 and I made them spin, it didn't matter, they spin no matter what I put in it, I say well since we're here, we're also going to add the LEDs and see what it does, that is, we have light, we have a fan, we have everything with This with how little look at the air that I have made in these and the light that I have seen flashes because it has pulsating direct current it would be let's try it by rectifying the current with a diode bridge but not happy with that I say let's put a little of a car a bit of a car this is already filament so we add it here I say let's see how it goes I know that with this the issue is no longer so easy and we are going to measure it and we are going to put it in conscious continuous it came to 12 volts but the good thing about this is that it is very light to turn, I can run all this with 12 volts and it is very light to turn, so it opens up a range of possibilities, as you can see, devices like this or the end cannot be ignored. of guasave hero I am really happy with the catch that day in the junkyard. Now also notice that we can use it no more and no less than the hydrogen cell, a negative and a positive, the attentive hay, start walking, look at it as a genre, that is, I I would have my manual hydrogen generator here, I can make it work, just imagine for a moment if I put this on a blade and we do it. work with the wind with the water with whatever, I'm crazy about this and we're also going to do another test so you can see the potential, don't go away, it's very good, we're going to take out this handle that I put a fake on and we're going to screw them here in the shaft a screw and and here we are going to put the drill so we don't have to turn it by hand we are going to connect this lamp that is 60 watts I think but 220 volts and we are going to put the multimeter here we are going to see what happens 118 volts, the lamp does not look as it should because it is 220 volts, so if it were 118 we would have it there [Music] [Music] plus we have to tell you that if we put any of the other things with the drill that we would put the voltage would be [ __ ] We're not going to test the cells. Positive, I don't know if the drill will throw it away, but let's try it. Or here, if I break my living room, let's get it out before we make any mess with this. Let's try the drill. The question is, could it pierce something, too? Let's check, let's try now to drill a hole in this wood using a drill, converting the energy of the drill into electrical energy and connecting a drill of that energy and thus we give room to those who want to criticize who say that it stops burning the drill to move another drill but well the idea is to make inventions we have to stop the wood from turning [Music] now so we don't have to press ah wow impressive with this drill I move the other drill and I still have energy left over almost continuous energy one thing don't think of asking later in the comments and if the energy that comes out of here we reconnect it we will be left running alone no no no you can't do that and we're going to try the last thing we're now going to see if it can move it I suppose it's going to move it like a drill but low or the pucha the better than the drill and even lighter I feel it here let's see well people I am very happy I tell you very happy with this [ __ ] we will see what it adapts here and what we are going to move it with but I assure you We are going to do something more than just a demonstration if you liked this video here you have my social networks follow me here don't forget to subscribe to the channel and activate the bell and share share share that we have to reach a million this year like this Let's see if we all give it a little push and reach it this year. It's a goal that I set out to achieve and well, we're going to try, but it's not just up to me, but up to you to subscribe and share. We're going to make a We are going to say hello to two people who have been first in previous comments and they are Miguel Ángel Arias García from Peru and Michael 2. For these two people, a huge greeting from Canal El Angelito and from myself. Well, friends, remember that here in the upper right corner of your screen I will be leaving you links so that you can explain there, follow some saga of other videos that may be related to this one or to some other that I want to show you, this has been all for this video and it will be until we see each other and I'm not going to return anything now, now I'll keep it for the engine.