Cadena Cubana hecho a mano (Cuban Chain Bracelet)

friends, how are you? name Boris Rueda, today we are going to make a bracelet for men or also known as a Cuban slave and for we need a wire with a diameter of 2.5 millimeters if you want to see how this wire is made, the link will be at the top and in the description of the video we will also need a tube that I will use this drill that has a diameter of 5.5 millimeters what we will do is hold this drill in this small press this to wrap the silver wire with a 925 law we will turn it around holding pressure so that all our rings have the same diameter now I will use this modified shipyard specially made to cut rings we will think about it we will use a hacksaw and a 2.0 saw this modified shipyard is very good to cut rings you only have to press it this way and the most important thing do not forget to subscribe and give it a good like here are all the prides that I cut that are 40 rings we will put it together from this f Orma joining it through the openings they have and to close this opening we will use two pliers and we will move it in this way because we will do this in all the rings now we will weld it on our rotary table we will place it in the center and the openings that these rings have it We will put looking up because this we will do with all the rings this to weld it quickly and we will color our welding liquid if you want to see how this welding liquid is made , the link will be at the top and in the description of the video we will light the torch to gas and we will use the hard type welding as you see I am jumping right in the openings that we place upwards this is the correct way to weld this type of rings always using our rotary table so that it is much easier to weld this method to weld rings is very good to weld all kinds of chains then we will strip it to continue working with our chain always strip your jewels to work much easier as you will see here I welded 2 rings in this way to hold it much better in this small press I will use this hand press and we will press one of these rings now I will start moving it clockwise pressing towards my side and we will start to go around until the chain is straight add more pressure it was a mistake of mine as you can see I used a hand press that does not have teeth but this time I would use this other hand press with teeth if you have this small press use it in this way having these teeth holds much better and it is easier to work with this tool we will give a half turn more when it is straight so that it is in this way here is our chain has to have this straight fall there we will know that it is very well made we will also need a small one table and we will use the sealing that we have to make first we will heat in sealing and we will make it melt on our wood and We will place homogeneously throughout this table now we will cut our chain in this way and we will heat it and you will notice that the sealing will begin to debate and adhere to our silver chain this like a little heat from the torch not very strong then we will straight it in this way it has to be as straight as possible now we will press it in this small dam and I will use this rough file and we will file the upper part as this is one of the methods to file this type of chain although you can also use sandpaper we will sand it In this way, for me it is much more practical and faster to do , the upper part is laying flat, this is how a Cuban chain is made, the upper part has to be flat but I want this chain to have a small angle to I like this style more with a modification to the Cuban chain, we incline it with a 45 degree angle and we start to sand it in this way I will do it on both sides for use. Raise this other sandpaper that is a little finer by sanding it diagonally at this 45 degree angle as you will see the upper part is straight and the sides have an angle of 45 degrees Finally we will use this finer sandpaper here you will notice how they have the angles the top is straight but the sides have an angle of 45 degrees and we will remove it with heat the same way as we place it with fire now we will make the plate for our Cuban chain and for this we will use a square silver wire of 1.5 millimeters of diameter and we will make a triangular cut now we will bend it with the flat point pliers we have to create two identical ones and we will put it together in this way because it measures 5 centimeters on the sides it measures 1 centimeter and in the central part which is wider it measures 1.5 centimeters and we will weld it with the hard type welding once welded we will also weld it on this 0.50 plate always placing it in the welding liquid and later In this iron we will use our rotary table if you want to see how this rotary table is made, the link will be at the top and in the description of the video, very easy to handle and very practical to weld all kinds of jewelry, it is already hot, we will use the type welding hard and we will weld it in this way and we will cut the surplus with a hacksaw and a 2.0 saw here it is cut but we have to cut some letters but before that we will give it some textures using the dremel that is like a kind of pneumatic hammer we turn it on and We began to create these textures this so that there is a contrast between the letters and it is much more noticeable now place a little solder paste on these letters so that it welds faster to create the insurance system of our Cuban type chain we need a spring and we will remove it from the lighter and we will cut an iron 13 millimeters long and 3 millimeters apart and we will bend it at a 90 degree angle s and we will create these small hooks to hold the chain and create 2 of these hooks we need to create 2 identical ones because the other we will cut with the hacksaw and 1 saw of 4.0 now we have to locate ourselves right at this point to guide the drill we will use this punch as we press and use a one millimeter drill bit I will also weld this small trapezoid the insurance system has to be set in this way the spring will go in the back to make pressure and the small hooks go down they also have to cut another plate to push in this way the insurance system is hooked with this small plate to release it we only have to press on the back and you will come out quickly Now we will weld another plate on the top using hard type welding if you want to see how this is done Hard type welding the link will be at the top and in the description of the video here they are already from our Cuban style chain with the s Insurance system because these would already be a Cuban-style slave, I would only have to polish it and it would be finished but since I want to place the plate that I made previously with my name on it, we will make some cuts at these points we will scratch it with the pencil on both sides we will cut it with a hacksaw and a 4.0 saw always guiding us with the lines that we made with the pencil here already corded I am placing a little coating on the rings of this chain so that the welding that the rings have do not join at the time of welding that is why I am placing the coating for the casting technique now I will place the soldering liquid and this my friends we will solder with the hard type solder always using our rotary table so that it is heated homogeneously I will push it a little it has to be very well glued and use the type solder hard on both sides be very careful when welding and remove the slave now we will place the first insurance system or we will hook one of these small hooks with a 1 millimeter thick wire we will place our spring on the internal part and place the other hook before riveting we will see if this excellent truth works well we will open it now if we will cut the surplus it has to be left as 0.10 on each side we will rivet it in this way, hitting it very gently and obviously we will polish it in the jewelry polisher if you want to see more ways and styles of creating jewelry here I leave some links so that you can expand your knowledge in jewelry techniques, take care that with me and as it will always be next time

Channel: ARTÍFICE JOYAS

Views: 121,957

Keywords: como hacer una cadena cunana, esclava cubana, como hacer una cadena, COMO HACER UNA CADEBA CUBANA CON BROCHE A RESORTE ( SILVER CUBAN BRACELET ), cadena cubana de oro, cadena cubanas, cadena cubana de plata, cadena cubanas con diamantes, como hacer una esclava cubana, brazalete cubano, SILVER CUBAN BRACELET, silver cuban chain bracelet, silver miami cuban link bracelet, Cuban Silver Bracelet, How To Make Silver Cuban Chain Bracelet | Handmade Silver Bracelet, artifice joyas

Id: R-EemtAafnM

Length: 19min 50sec (1190 seconds)

Published: Thu Apr 29 2021