So, letās say youāre considering an electric car but you donāt know what living with one might be like or what you might need to keep it charged up. Youāve landed on the right video! Iāll be covering the ins-and-outs
of living with and charging EVs in 2022, from what chargers are out there for home use, how to choose the right one based on your needs, vehicle, and situation, what traveling long-distance is like now and what needs to be improved, and what hiccups to look out for particularly in cold weather. This will be a largely US-centric conversation,
especially when we talk about stuff like volts, amps, and miles... per gallon... of gasoline, but the broad strokes apply no matter where you are. My goal here is for you to have a fairly complete
understanding of electric cars so you can make the most educated and rational choices
for your personal needs. Before we get started, youāve probably already
noticed that this video isā¦ quite long. I want this video to answer as many questions
and concerns as someone entirely unfamiliar with electric cars might have, and all in one place. So thereās a lot of information here. Chapter markers are there to help you move around. But I want to stress that in day-to-day life,
Iām not thinking about any of this stuff! I simply plug in my car and walk away, and in the morning itās full again. Although it takes my car several hours to charge, I spend seconds plugging it in and it charges while I'm asleep. That means I actually spend much less time refueling compared to negotiating a gas pump transaction every week or two. I can tell you with absolute certainty that
I would never go back to a gas-powered car. An EV is simply much more convenient and easier
to live with when you can charge it at home. And I know not everyone can do that right now. Thatās something we need to work on. But if you can, hereās the situation in a nutshell: If you drive the typical average distance daily, a regular household outlet
might actually meet your needs. And if you need or want a little more power,
donāt assume youāll need an electrical service upgrade; a basic 20A 240V circuit can easily
cover very long commute distances - up to 100 miles - every day, charging only overnight. And any car can plug into any charger of any capacity - donāt chase the fastest charging
speed a car supports unless you really need it. How do you know if you really need it? Well, do I have a video for you! Itāsā¦ itās this one. ā« Music ā« With that, we need to start with the basics, and I mean the really basic core tenet of everything: energy. How much energy does an electric car use? How much can it store in its battery pack? How far will that take you? And how long does it take to replenish that used energy? For a while I was struggling
with how to begin answering these questions - electric vehicles require different thinking
than what you might be used to and as we go on youāll see why. But, well I kinda forgot that we can in fact translate most concepts from a combustion vehicle to an EV. Since more of you are familiar with those than EVs, letās start with this: the battery pack is the new gas tank, and the kilowatt-hour is the new gallon. An electric carās battery pack doesnāt have a capacity in gallons, of course, but it does have a capacity. Rather than giving that capacity in volume of a liquid chemical concoction, we define its capacity in raw energy terms. Energy. It makes the world go āround! But what is it really? This section is going to feel like weāre deep in the weeds but itās fundamental to understanding how charging works. First, you need to understand the difference between power and energy. This trips a lot of folks up because itās a bit confusing. You probably have a general sense
of how much power things in your life use, for instance light bulbs are given a wattage. The watt, though, is a unit of instantaneous power, not energy. Quantifying energy from power requires a time component, and in the realm of electricity we use the watt-hour. Watt-hours are what they sound like. Itās simply the average power draw in watts
that occurs over a period of one hour. As an example, a 10 watt light bulb that has run for 1 hour
will have consumed 10 watt-hours of energy. When you change the power level,
you change the speed at which energy is consumed. A more powerful light bulb will burn through energy more quickly. For instance a one hundred watt light bulb only needs to run for six minutes
to have consumed the same 10 watt-hours as our 10 watt bulb does over an hour. It uses 10 times as much power, so the same total
energy use is reached in one tenth the time. Watt-hours are pretty small, though, so when
talking about electrical energy we usually use the kilowatt-hour - which is just
one thousand watt-hours. Your electric utility probably bills you in this unit. And the battery pack capacity of an electric car is given in kilowatt-hours. Battery-electric vehicles on the market today (meaning those which are purely electric, not hybrid powertrains) usually have battery packs of at least 30 kilowatt-hours,
though 50+ is more typical in the US market. Many models are available with different pack sizes to choose from, for instance my car - a Hyundai Ioniq 5 - can be had with either a 58 kWh pack
in its base configuration, or a 77.4 kWh pack, the size I have. Of note, right now, car manufacturers tend to be a little vague on whether the figure they give their battery packs is the packās
actual capacity or a usable capacity. See, to prolong battery life most cars only give
you access to a certain range of the packās charge levels. It puts more wear and tear on a battery cell when you push it to its extremes, so somewhat typical is for a 100% indicated charge
to really be something like a 95% charge, and when the battery is ādeadā at an indicated 0%,
itās really more like 5% charged still. To be clear, this is a good practice! But I wish every manufacturer would give distinct gross and usable capacity metrics for their battery packs so we can understand how much theyāre pushing the cells. For what itās worth, many EVs will let you be gentler on their batteries
by allowing you to set a maximum charge level. I have my car set to stop charging at 80% because honestly it has way more range than I need, and limiting charge levels is thought to prolong battery pack life. Anyway, letās go back to what I said earlier. The battery pack is the new gas tank,
and the kilowatt-hour is the new gallon. So, my carās ātankā holds 77.4 kWh. And how many miles can each of those 77.4 kWh take me? On the highway, about three. This car, like lots out there, actually gives you efficiency
in miles per kilowatt-hour, and just like miles per gallon, a higher number is better. Some cars will flip that and tell you how many watt-hours you consume to go a mile, but I find distance-driven per kilowatt-hour to be much more human-friendly, especially since I pay for electricity in that unit. How far can a full ātankā take me, then? Itās the same math as a combustion
vehicle, just with different units. 3
(our distance we can go with a kWh of energy) multiplied by 77.4
(how many of those kWh our pack holds) gives about 232 miles of range, a bit shy
of the 256 miles my car is rated by the EPA to go. Thatās because the EPA rating includes
mixed driving, and in the realm of EVs, highway driving is less efficient than stop-and-go. Iāll explain why later, but for instance around town Iām regularly hitting 4 miles per kWh in this car, but at sustained highway speeds that just isnāt possible. Heh, right, speaking of the EPA, some knucklehead thought that MPGe was a good idea. If you look at the window sticker of an electric car
itās gonna be prominently given a fuel efficiency in Miles Per Gallon-gasoline Equivalent. [exasperatedly]
Hereās how that works: we assume a US gallon of gasoline contains 33.7 kWh of energy. Then, based on the actual energy consumption of the vehicle in real units, a backhanded calculation is done to give you
Miles per Pretend Gallon. I... itās not exactly meaningless, itās nice to see how much farther an EV will take you
with the same amount of energy. But nobody buys electricity by the gallon,
so miles per kilowatt-hour makes way more sense. That would be too easy, though, so if you want to use real units the EPA gives them to you, but they tell you how many
kWh of electricity the car needs to go 100 miles. Look, playing around with different energy units is fun
and you can do it however you like, but MPGe is just a wee bit silly, dontcha think? Anyway, thatās the basics. Electric cars have a battery capacity in kWh, and we measure a carās driving efficiency
in much the same way as miles per gallon. And that efficiency multiplied by the packās capacity gives
you its driving range. If youād like to get an idea of how much it will cost
to charge your electric car, well again the basic math is the same as with a gas-powered car,
just with different units. Take your commute distance and divide by your carās efficiency. Iāll do a 40 mile commute as an example,
and divide by my carās 3 mi/kWh highway efficiency. I should expect an all-highway 40 mile commute to need 13.3 kWh. Now itās a simple matter of determining
how much your electric utility charges per kWh. Supposing a cost of $0.15/kWh, that commute will cost $2.00. Now Iāve ignored charging losses with this calculation;
adding 10% will give a more accurate cost. Public charging tends to be more expensive,
but weāll get to that in a bit. ā« Music ā« I know the next thing a lot of you want to know is
how long it takes to charge a car back up and thus refill its proverbial tank. The answer is actually so simple it only needs two words. Are you ready? Now, donāt worry, once you get your head around a few variables,
youāll be able to answer this quite confidently. Thatās literally my goal, here! For now, weāre going to focus
on āslowā AC charging. If you have regular access to a "slow" charger which can fill your car up overnight
(or perhaps when youāre at work), youāll never even think about
visiting a charger when youāre out and about. And one of the most beautiful things about
the power grid is that itās everywhere! Level 1 and 2 AC charging simply connects
a car to the grid in the same way you do anything else, from a table lamp to a clothes dryer. But Iām getting a little ahead of myself. To answer how long it takes to charge, thereās really only one critical factor: how much power you can deliver to the car. Weāll get into details on how exactly thatās accomplished shortly, but when you know how much power you have available
and you know the size of your battery pack, solving for time to fill it is really simple math. All you do is take the battery pack size in kWh
and divide it by the power supply in kilowatts and there, youāve solved for hours! Hereās an example for determining charging time. Say you have a car with a 60 kWh battery pack,
and a charger which can supply 5 kilowatts. 60 divided by 5 is 12,
so that car would need 12 hours to charge from empty to full with a 5 kW charger. But if you had twice the power, 10 kW,
the charging time would be cut in half to six hours. 60 kilowatt-hours divided by 10 kilowatts is 6 hours. And if you only had 3 kW to play with, charging time would be stretched to 20 hours using the same math. But itās important to keep in mind that charging time also depends on how charged the battery already is. A half-full batteryā¦ is already half-full! So in our 60 kWh example car,
a 50% charge means only 30 kWh actually needs to be fed to it. That cuts all those charging times in half. This is because on AC charging, since the
battery pack is so large and the power input is relatively low, the charging curve is essentially linear. Weāre not dealing with the effects you might be used to
with a phone or laptop battery. What really matters is how much energy was taken out of the battery,
and how much power we have to refill it. Again, this is in the case of AC charging. DC fast charging is another story, which weāll get to later. Now, manufacturers will give you a required
charging time for their cars. But honestly, you should probably just ignore that. See, if you were to look at Hyundaiās information on my car, theyāll tell you that it takes a little less than 7 hours
to charge it from 10% to 100% on a 240V charger. Thatās pretty good for an up-to 300 mile EV. But, I donāt like that answer. At all. To be clear itās not wrong - that speed is absolutely possible! But only if you have a charger with enough
capacity to support that speed. Which I donāt because, frankly, I think itās very much
overkill for virtually anyone. But again, getting ahead of myself here. A while back I made a video on what exactly an EVSE -
the technical name for a car charger - is, does, and how it works. I wonāt get into the specifics here, if youāre curious watch that video! But the key thing to know is that the actual charger, meaning the device that takes AC power from the grid
and converts it to DC for charging the battery cells, lives in the car. The voltage conversion and all that stuff is entirely the carās job. The EVSE is just a very-slightly-smart power cord which delivers raw AC voltage to the charge port and tells the car how much power itās allowed to pull. Thatās all this does, plus a few safety things. Hyundaiās charging time claim comes from the fact that the Ioniq 5ās onboard charger can accept a maximum of 48 amps, and at 240 volts thatās 11.5 kW. 77.4 kW-hours divided by the carās maximum power input of 11.5 kW tells us that we need 6.73 hours of charging time
to deliver an entire battery packās worth of energy, exactly what Hyundai claims. Now, hang on, they claimed that time from 10 to 100%, and we did the math for 0 to 100% - why the discrepancy? Well, there is about a 10% loss when charging a battery, in other words only about 90 of every 100 kWh pulled
by the car ends up stored in the battery. The rest is lost as heat in chemical processes
and various charging components. But in the end, and this goes for any car, all you need to know to determine
charge time are three variables: the size of your battery pack, how much of its capacity you need to recover, and how much power your charger can deliver. Add 10% to the end result
if you want to be really accurate. Manufacturers are generally going to quote an empty-to-full
time on the fastest charger the car will support - thatās useful to know and is a simple selling point,
but the real world is messier. Usually in good ways! ā« Music ā« So now, letās talk about what sort of charging
solution you might need. First, let me acknowledge that I know there are lots of you out there who need to drive a car but donāt have a dedicated place to park and charge one. Trust me, Iām not trying to be dismissive of your situation. Iām just as frustrated as you are! See, the beauty of AC charging is that itās simple! Itās incredibly straightforward infrastructure to deploy, and thereās no reason it shouldnāt spread to multi-family
dwellings and areas with on-street parking other than finicky details like permitting,
billing structures, maintenance concerns, building codes, and miscellanea like that. The good news is that there are plenty of creative solutions in the works and Iām sure weāll see more of them with time. So while I donāt have answers for you here,
keep your eyes peeled. For those lucky ones who have a garage or
even a driveway close to their home or other electrified structure, well youāre probably pretty good to go. In fact you might already be set. Actually, right, hereās a misconception
I keep seeing pop up from time to time: This connector design is waterproof ā thereās a gasket in here which seals the pins from the elements when a connector is attached. And charging your car outside is totally OK. There is plenty of charging equipment
meant to go outdoors, so donāt assume youāll need a covered parking spot. You can simply install a charger on an outside wall near to where you park. And plenty of cars these days can lock the connector to the car to keep bored teens from unplugging it while you sleep. The other thing to mention is that in the US market, this J1772 connector is an industry standard followed by all players... except Tesla. Tesla uses a proprietary charging connector, for better or worse. Iām not going to relitigate this whole debacle as Iāve done it several times now with increasing levels of exasperated snark, but you should know that throughout this video
Iām assuming that youāre looking for a charger that is directly compatible ā no adapters needed ā with literally every
plug-in car sold since 2010 and literally every option on the market today except for
those models made by That Company. Even if you want a vehicle made by That Company, I would suggest installing a J1772 charger as a simple adapter which is provided with their vehicles will allow you to plug into it. And if you want one of the dozens of options that
arenāt S, 3, X, or Y, youāll charge in dongle-free bliss. But thereās a good chance that you might
not even need to install a charger at all. ā« Music ā« If you drive a fairly average amount, say up to 50 miles a day, one of these little guys might actually take care of you just fine! Level 1 charging is charging on 120V power, and most of the time this involves simply plugging your car into a household outlet through a portable EVSE like this one, which many vehicles come with. Here in the US an EV can draw 12 amps through this sort of supply. At 120V thatās 1.44 kilowatts. Thatās not a lot, but in a very efficient EV,
50 miles of highway driving might take as little as 12.5 kWh. Assuming some losses that will take about 10 hours of charging to recover. Now, thatās admittedly a long time. But Iām willing to bet that you sleep for long enough
to cover the bulk of your charging. Level 1 charging isnāt for everyone and has drawbacks,
but I would argue itās more useful than many realize. When I first got my 2013 Chevy Volt, which only had about a 40 mile electric range from its 10.5 kWh pack, I just plugged it into a regular outlet. Its small battery pack meant that it only ever
took 10 hours for a complete charge. And with a 32 mile round-trip commute, I was driving
entirely on electricity every day. My next job was nearly twice as far away at a 60 mile
round-trip, but by asking nicely and bringing a cord protector with me to keep folks from tripping on it, I was also able to plug-in during my workday - again, to a bog standard outlet. Usually Iād be topped off by the end of my shift, so even then I was doing an all-electric 60 mile commute with only level 1 charging and a 40 mile range. I would shortly move a little further from work, proving that even a 70 mile commute was possible in
the Volt with only Level 1 charging at both ends. At least, for the seven or eight warm-enough
months of the year.... OK, I spent too much time on this so hereās
a condensed voiceover. Level 1 charging is slow, and since cold weather decreases driving range, if you live in a cold climate a 40 mile commute might be cutting it close. And I'm not gonna pretend everyone can plug in at work. I just wanted to give you an example of its potential. L1 charging is also less energy efficient since the carās charging electronics need their own power to operate, and with only 1.4 kW controls and monitoring
start to take up a larger percentage of the power available to the car. That effect can also be problematic if you park outside and the car needs some power to heat its battery pack, leaving little power for actual charging - but thatās very model and circumstance dependent. Plugging into a standard outlet may also present
problems depending on what else is on the same circuit. That is especially notable in older homes. And, a 12 amp load on a normal socket is kind of a lot, and old,
worn-out receptacles present a hazard. Thatās easy to fix by replacing the receptacle,
but you should be aware of that. And in case youāre watching from one of those 240V countries
where boiling a liter of water takes 2 minutes in a kettle, you should definitely not rule out charging off a standard outlet because you have more zippy zappy to play with. The last main drawback of Level 1 charging is that, since you need your car to be charging essentially whenever it can, you wonāt be able to take advantage of time-of-use rates if your utility offers them. Since my power is a lot cheaper at night,
I benefit from having a more powerful supply to my car. So I have one, and the car is programmed to wait to charge until midnight,
a feature nearly all EVs offer. My more powerful charger is a 240V charger, so itās classified as LEVEL TWO. Now, an annoying thing about the classification āLevel 2ā is that it can be anything from 2.5 all the way up to 19.2 kW. Thatās all LEVEL TWO so as a category itās just not that useful. Itās another reason I donāt like Hyundai saying it takes 7 hours on āa 240V chargerā to charge my car. And wait ātill we get to the fact that sometimes 240 is 208. Anyway, letās say you need or want a Level
2 charger installed. Whatās that gonna look like? Here comes that 2-word answer again: it depends. ā« Music ā« First thing I want to say ā if you are building a home or buying new construction, even if you donāt have an electric car right now, ask to have one of these installed in your garage. This is a NEMA 14-50 receptacle, and it supplies enough power to charge
virtually any EV from empty to full overnight. Many inexpensive car chargers are out there which
plug straight into this nasty fella and itās sort-of becoming an unofficial standard EV charging plug over here. To clear up a sort-of mistake of mine, in my video on EVSEs I suggested a NEMA 6-50
which doesnāt have the fourth, neutral pin. See, I had already bought a charger
from Costco which featured a 6-50 plug and thought since an EVSE doesnāt need the neutral
that's probably what most EVSEs are gonna plug into but nope! There are way more options for 14-50 plugs out there, possibly because big RVs use that plug
so itās fairly common at campsites. But moving onā¦ Hereās another fun angle, do you have an electric clothes dryer and is it close to where you charge your car? If you have a conventional electric dryer, and itās in or near to your garage, you already have a 30A 240V circuit at your disposal. And inexpensive chargers are available whichāll plug right into it. A 30A circuit wonāt give you the fastest charge out there, but itās over 5 kilowatts which is, trust me, plenty. Now, donāt worry, you donāt need to keep unplugging
and replugging your dryer every laundry day. There are simple splitters on the market designed to let you
have both an EVSE and a dryer plugged into the same receptacle, but you will have to remember to unplug your car before you use the dryer should you go that route. Really, though, if you have this option - take it! But if youāre not in that lucky boat, to add a charger to your existing home youāll need a new circuit run from your electrical panel to wherever you charge your car. If your panel is in or near your garage, this will be a cinch
and should only cost you a few hundred dollars. If itās farther away, expect to pay more. Since Level 2 chargers are 240/208V and require both hot legs
you will need two free spaces in your breaker panel. If you currently have none, you may
be able to consolidate some circuits together - consult your electrician for whether or not thatās possible or allowed where you live. Oh, and definitely donāt assume you
need an electrical service upgrade to drive electric - I would argue you almost certainly donāt. There are also some pretty exciting developments when it comes to breaker panels which will come up in a future video. But assuming you do have the space for a new
breaker in your service panel, well hereās broadly whatās gonna happen. A new two-pole circuit breaker will take up two spots in the panel, and a two-conductor with ground cable will be connected with the hot wires to the breakerās lugs, and the ground to your ground block. That cable will then exit the panel and run through walls, attics, or whenever code allows until it gets to where you want your charger. If youāre hardwiring a charger,
youāll stick a junction box on the wall where that cable ends up, pull the wires into the box
and connect them through to an EVSEās incoming power wires. If youāre installing a high-power receptacle, itās much the same idea. Close up the panel and box, close in the breaker and energize the wires, and youāre done. This is a really straightforward process,
so much so that Iāve done it myself two times now: once for my parents, and later for me. DIYing itās not for everyone, and different chargers may need different things - for instance, really big EVSEs actually need a disconnect switch as well. But when it comes to electrical work this is really simple stuff, and the simplicity here is one of many reasons Iām much more excited about EVs compared to, say, hydrogen. And when you have a circuit like this available in your home, you are seriously never going to think about charging. You can have a full battery every day
and the idea of stopping somewhere to get a top up will just leave your mind. Itās truly amazing and I hope everyone who needs to drive can experience this. ā« Music ā« Assuming you have the option of running a new circuit, well now comes the time when youāll need to decide
how large of a circuit you want to run. And here Iād like to whip out my Midwesterner card
and strongly convince you to not go overboard. There are a lot of people who think that theyāre gonna need
a big honkinā 50A circuit with expensive 6 gauge wiring to charge their car. And Iāve seen multiple folks in two car families presume that theyāll need two of those very large and expensive circuits to drive electric. Hereās my spicy take; ya donāt. The only scenario where you would actually need that much power is if you and your partner *each* drive over two hundred miles every single day. Iāve seen so many folks in comments, product reviews, and really wherever else online get into this mindset that they want the fastest charger possible. Theyāll immediately start looking for massive high-power charging stations and often seem to assume that if they were to buy a car which *can* charge at 10 kW,
they'll need a 10 kW charger for it. I mean, if you can swing it go ahead but thatās not how it works. Any car will work on any charger and simply limit its power draw
based on a capacity signal coming from the charger. Thatās how the standard works. So donāt just rush out and buy the fastest charger for your car - itās expensive and may come with more headaches
than you bargained for. How do you know what sorta charger you actually
need? Simple, you just listen to me! Itās 7.2 kW. Thatāll do fine! Iām kidding, but actually not really... I consider that to be the āvery goodā speed thatāll
work for just about anyone but to give you some real information in the realm of
electric vehicle supply equipment, amps are what matters first and foremost. Wires of a given thickness can only handle so much current, ultimately making amps allowed on a circuit the limiting factor. So when you look for a charger, youāre gonna find them listed by amperage. Thanks to the 80% rule which limits continuous loads to 80% of a circuitās capacity, youāll usually find two amperages listed: the size circuit a given unit requires,
and the actual amperage it can deliver to a car. Now, I know weāve been talking in kilowatts
and now Iām throwing amps at you. Sorry about that. To know the power output of a charger in kilowatts, you simply multiply amps it can supply by the voltage of that supply. That is usually gonna be 240V, but in some settings
(mainly in large buildings which have three-phase power) it might be 208V. Itās a relatively small difference, so itās not worth getting too hung up on, but be prepared for the same charger in a home setting to be just a little bit slower in a commercial setting. Hereās a chart of all the common circuit sizes and
how much power that nets you. To make comparisons to real life a little easier, we can use a cheat. You will somewhat commonly see circuit capacities
be given a āmiles per hourā figure. This is useful, but a little messy. A ātypicalā vehicle will gain about 10 miles of range per hour on a 20 amp charger, 15 miles per hour on a 30 amp unit, 20 mph on a 40A unit, and Iāll let you do the rest as homework. Oh and Level 1 charging, remember thatās just plugging into a household outlet, gives you about 4 miles of range per hour,
maybe 5 with a really efficient EV in perfect conditions. Using these miles-per-hour speeds is a decent starting point
but now that bigger EVs are on the market, itās beginning to fall apart. My car lines up with those figures pretty well
at 3 miles per kilowatt-hour on the highway, but of course in winter it needs a little more time since it uses
more energy to go the same distance. And a vehicle like an F-150 Lightning will,
based on what the EPA says, only gain about ā
as much range per hour itās plugged in as
the conventional speeds wisdom. So Iād argue itās better to think about this in energy terms,
but giving a charger a speed like that is handy. So handy, Iām gonna use it right now! The next thing to do to help you determine
how large of a charging circuit you might need is to multiply that miles-per-hour figure by
hours plugged into a charger to get a sense of how many miles are regained in that time. Iām gonna go ahead and work with a 10 hour overnight charge time
since lots of you sleep for 8 hours and a morning and evening routine tacks on a bit at each end. If youāve been following along then youāll know a 20 amp circuit gets you 100 miles of range overnight, 30 amps gives you 150, 40 amps 200. And again - I'll leave the rest for homework. Notice how the smallest number I just gave you was 100 miles. Iām going to stress this point.
And Iām going to be obnoxious about this because I really need yāall to know this and deeply: A 20 amp circuit. Which is not a whole lot. And which can be run with cheap 12 gauge Romex, can make even a crossover-sized EV like mine go 100 miles every single day, charging exclusively in the overnight hours. You do not need a giant charger. Yes, I hear you, what about all those "but sometimes!" situations youāre thinking of? Like winter, for instance! Well, even if we assume an extreme 40% winter range loss, youāre still getting a 60 mile round trip commute recovered every evening. And letās be real, you can probably charge your car for a bit more than 10 hours every night if you really needed to. Now Iām not saying everyone should limit
themselves to 20 amp circuits for their car chargers. I myself use a charger which is twice as powerful. But Iām only doing that so I can drive 100 miles in a day
(a thing I regularly do) and top the battery up entirely during off-peak hours,
taking advantage of low overnight power rates. If I didnāt care about that, frankly my life would not change
one bit if I were limited to a 3.8 kW charger. Even my long drives would be recovered overnight, but I might need to charge from 9:00PM to 7:00AM rather than midnight to 5:00 AM. The reason Iām so passionate about spreading this gospel is that I know there are lots of you with only 100A service or possibly even less that have ruled out an EV because youāve assumed youāll need a service upgrade. Iām not gonna tell you that you definitely wonāt because
I donāt know your particular situation, but you should know that a car charging on a 20A circuit only pulls 16 amps. Thatās only 16% of your capacity if you have 100A service. And yet, that can take you quite far. A conservative 20,000 miles annually
charging only 10 hours a day and only on work days. Itās important to note that you canāt just add up the breakers in your panel to see how close you are to using up your service level. In nearly all homes youāll find the total circuits far
and away exceed the main breakerās rating. You need to think through whatās on those
circuits and how often they get used - an electrician should be able to help you with that. The other reason Iām pretty gung-ho about basic level 2 chargers is that the wiring needed for them is cheap and plentiful. So long as your garage or driveway is close enough to the service panel that voltage drop doesn't become an issue, this stuff is all you need and the going rate right now is about $80 for 50 feet. And heck you can step up to the orange stuff, 10 gauge,
and run a 30 amp circuit the same length for about $50 more. And, uh, those of us who live where Romex isnāt legal can cry
in a corner and hope that armored cable is up to code. Anyway, before you get scared off thinking
you need panel or service upgrades, Iād encourage you to think long and hard about
whether thatās truly necessary in your situation. I can tell you from experience that a 20A
charger on wiring like this would have easily taken care of my 70 mile commute even in the dead of winter,
and even with my crossover-sized vehicle. If you have the wiggle room, though, I would personally suggest
that you run a 40 amp circuit for a 30 or 32 amp charger. I consider 7.2 kW to be the Certified Midwestern Goldā¢ standard of charging. You have to drive an awful lot and with a pretty inefficient vehicle for this to not meet your daily needs. Over 10 hours, such a charger will push something like 65 kWh into a battery pack after losses, which is about 200 miles in my car. Itās the vast majority of the pack. And even with a vehicle as large as a Ford F-150 Lightning,
thatās 130 miles of range recovered every night, nothing to sneeze at. To give you some sense of how Absolutely Fineā¢ I consider that charging speed, well at home I do indeed have a 50 amp circuit going to this receptacle so I could charge at 9.6 kW, but I only bought a 7.2 kW charger (because it was a lot cheaper)
and I see absolutely no reason to upgrade. Aha, but what if your household,
through the magic of having two of them, needs to charge up two cars? What now, Toaster Boy? Well, the first thing Iād like to point out is when you get your hands on a 200+ mile EV, a funny thing happens. You stop bothering to plug it in every day. It begins to feel kinda silly never discharging the battery pack below 80%,
so you just sortaā¦ end up behaving like you did back in the dino juice days
and only plug it in when you really need to. I guess I shouldnāt speak for everyone
but honestly at this point I really only plug the car in after a long journey, otherwise I'll go a solid week without charging it. 200 miles is a long distance, folks! Thatāll get you from Chicago all the way across Illinois
and solidly into Iowa. I really hope youāre not commuting like that. So if you have to charge two cars, first donāt
jump to the conclusion that youāll need to run two circuits. A single charger can easily be shared. If you feel like thatās too hard or have some weird parking space
restrictions or something like that, well there are also options in which two EVSEs share a single circuit. They talk to each other and split power between two cars if
theyāre both charging at the same time. But trust me, the simple and free solution of just figuring out a system works pretty friggin great. On Mondays, Carl parks on the left, and on Tuesdays, Brenda does. Alternate and then switch on the weekends. You can do it, I believe in you! And if one of you gets in the habit of backing in
you might not even need to switch places! Obviously if youāve got a bigger family
where more than two people drive cars, this gets more complex and there may very well
be value in having multiple charge points in your situation. But think long and hard about how powerful those chargers actually need to be. Remember, a 40 amp circuit can
push 200 miles of range in a car over 10 hours. Even if there are four drivers in your household, your daily miles driven need to add up to over 200 miles
before that power level really starts to limit you. But weāre getting well into edge cases now, letās reel it back in a bit. At this point weāve covered pretty much
everything I think you need to know about AC charging. Bottom line: Level 1 might work for you, so donāt rule it out right away. But if you need more power, even a really
basic Level 2 charger can take you places. If you can swing a 7.2 kW charger, I think
youāll be happy no matter what you drive. And going above that level might be necessary, but really only if you drive a big vehicle very far every day. Now letās talk about DC fast charging! ā« Music ā« First, and I know I sound like a broken record, DC fast charging should really only be necessary to enable long-distance travel. I hope you can see why āslowā AC charging at home
(or even at work if you have that option) is where itās at - itās cheap infrastructure to set up, and itās way more convenient
to charge while youāre sleeping (or working). Then youāre never actually waiting. We just need to figure out ways for it to spread outside of the easy targets of single-family housing and the like. I promise you thatās a much better future for all involved than turning todayās gas stations into fast charging stations. Weāll need some of those in-town for getting
folks out of a jam or for day trips and whatnot. But DC charging should really be the exception and not the norm. Iām not going to talk too too deeply about
DC fast charging here because Iāve made a video already on that tech. Clicky thing, link below, you know the drill. But that video didnāt touch much on the more persnickety
details of todayās battery tech. It was mainly about the chargers and how powerful they are. Which, to be clear, theyāre very powerful! These chargers have an output in
kW and we can do the same math we did for AC charging to figure out charge times. The quasi-standard 150 (!) kW chargers are fast enough to completely charge my carās 77.4 kWh battery pack in 30 minutes, and a 350 kW charger could do the same in only 13 minutes. Except, they canāt. Not because of the chargers but because of the batteries. When DC fast charging, those effects you might be used
to with a phone or a laptop are now in play. Todayās battery chemistries can only be charged so quickly, and how fast you can do that changes based on a number of factors, most prominently how charged the battery currently is. Right now itās common for car manufacturers
to give a 10% to 80% charge time. My car manages that in 25 minutes at a 150 kW charger, and
18 on a 350 kW charger. Beyond 80% state of charge, charging speed drops quite a lot because,
for physics and chemistry reasons, it becomes a lot harder to push electrons into the battery cells. Iāve seen a few folks fixate on this and even view it as some sort of cheating
or false advertising on the part of automakers but, well hereās the thing. You donāt actually need to top up every time you charge. Itās a huge waste of your time to get that last 20%
when thereās another charger 100 miles away. Sure, youāll end up needing to charge more frequently since youāll effectively only be using 70% of your range between stops, but in my car thatās still over 170 miles. Stopping for a 20 minute charge after every two and a half hours of driving isnāt nearly as bad as you might think. I legitimately quite enjoyed it, though to be fair my car charges exceptionally quickly. Iād be very surprised if just-as-fast-to-charge models
donāt become the norm pretty quickly, though. Many EVs will help you plan a route in their navigation software which optimizes for the least time required at chargers
based on their battery packās charging curve, although you can also play around with apps such as
A Better Route Planner if youād like. Or if, like me, you have a car which justā¦ doesnāt help with route planning. Iām not too bummed by my carās omission there, though, because I fully expect DC fast charging stations along highway corridors to proliferate pretty quickly, and make that sort of planning ahead less necessary. However, there is one thing my car doesnāt really do,
at least not yet, that it absolutely needs to: battery preconditioning. Todayās battery chemistries are happiest
within a certain temperature range. Nearly every EV on the market - even the original Chevy Volt -
has means to heat and cool the battery pack to keep it in its happy place. But when DC fast charging, to get the fastest possible speeds the battery cells need to be pretty warm - warmer than they otherwise need to be to drive. And in the winter, if the battery isnāt warm enough DC fast charging may beā¦ not so fast. At least, not at first. Once the car realizes itās on a fast charger
itāll start heating the pack up as fast as it can, but since the battery is so massive, that can take a while. You could easily see a 20 to 30 minute increase in charging time when itās cold out. Certain EVs, notably Teslas and a few others as well, will start expending energy to warm up their battery packs as you approach a DC fast charger. This battery preconditioning allows them to accept maximum power, or close to it anyway, as soon as itās plugged in. This is an important feature that needs to roll out to all EVs, in my opinion. Frankly I donāt care if itās as fancy as Tesla's or Porscheās implementation where it knows youāre headed to a fast charger because youāre navigating to one - as a matter of fact I kinda donāt like that as someone
who navigates with Waze using Android Auto. Iād rather there just be a button I can
press or a voice command I can give when Iām 15 miles or so from the next charger. But I do appreciate how the automated schemes
would keep me from forgetting to do that. With all this said, the biggest issue with DC fast charging today is that we barely have enough chargers right now. Already some popular corridors are experiencing charging queues,
and this will get worse as more EVs are sold. The good news of course is more EVs that are sold
means thereās more demand for chargers, but weāre in the midst of growing pains. Like, for instance, charger reliability is a growing concern, and some network operators are less-than-great at operating their networks. My personal belief is that a lot of this comes from the fact that DC fast charging technician is a very rare job title right now, and with the current makeup of sparsely-spaced chargers, getting to them when they need parts or repair is a chore. I donāt mean to use this as an excuse, but it does make me fairly confident
this will get better with time. But letās move on from DC fast charging and finish up with some pointers on factors which affect your driving range. ā« Music ā« Iāve brought it up a few times already but if you live in a cold place,
in winter driving range drops. And Iād like to tell you itās just a little bit,
but unfortunately it can be significant. I do want to stress again, though, that with todayās EVs, so long as your commute is reasonable and you have access to a charger at home, these range losses are unlikely to impact your day to day needs. They will extend charging time and cause you to spend a little
more money on charging, but when you are only driving an average of 40 or even 80 miles a day,
itās not a big deal. Long distance driving does have some challenges, though. You might want to ask, why does this cold-weather range loss happen? Well, a huge part of the range loss comes from using the cabin heat. In a combustion vehicle, the explodey machine under the hood is so bad at turning chemical energy into mechanical energy that it ends up with all this waste heat it needs to get rid of. Thereās literal explosions happening over a thousand times per minute,
and explosions are hot. Dealing with that heat is what the carās cooling system and radiator is for, and by running a second circuit of engine coolant into the cabin and through a small radiator called the heater core, the excess heat from the combustion can be used to keep you warm. Since it would otherwise be wasted, itās free heat. Electric vehicles, though, donāt produce much waste heat at all. This is cool! Itās why the world is excited about them, theyāre just much, much, much more energy-efficient. But that means that when you want to warm
the cabin, you have to take energy out of the battery pack. And that leaves you with less for driving the car. With an EV that has a resistive cabin heater, youāll start to notice range dropping around mid-fall. Basically as soon as you start needing to use the heater. It will be pretty mild at first, but once youāre into the true winter months,
you can expect about 30% range loss. My familyās 2017 Chevy Bolt went from reliably hitting 230 miles of highway range in the summer down to between 160 and 170 from December to early March. Using seat heaters more and cabin heat less can help, but whenever you need to use your defroster
youāre kinda stuck running the heat. Unless of course you have one of those cool direct-heated
windshields, a feature I think should be standard on EVs! Speaking of features, one feature thatās finally spreading to more and more EVs is, drumroll please, HEAT PUMPS! If youāre not familiar with this channel, I love heat pumps. Theyāre the hottest cool things around. By doing what essentially amounts to running an air conditioner backwards, you can collect and concentrate heat energy from outside and move it inside. And since pretty much every EV out there has air conditioning, making it reversible was an obvious next step. I don't know why it took so long. Doing this allows an EV to cut its energy consumption for cabin heat by up to 75%, as moving heat takes a lot less energy compared to creating heat. For the 2022 model year, Hyundai gave all-wheel-drive Ioniq 5 models a heat pump. Iām hoping they make that standard soon because let me tell you,
it makes a big difference. I took delivery of my car in February
so I havenāt yet experienced the worst of the worst winter conditions, but from what I did get to see earlier in the year,
a 15 to 20% winter range drop seems fairly typical. When it gets extremely cold, the heat pump does need to be supplemented by a resistive heater so larger range drops are possible, though. Oh, and Iād like to dissuade fears of running out of battery juice
should you get stuck in traffic or worse stranded in a blizzard. The carās heater needs to work a lot harder when youāre in motion because all that wind rushing against your car does a great job
of sucking heat right out of it. But when youāre slowed or stopped, thatās not happening.
At least, not nearly as much. In the Chevy Bolt youāve seen some adventures in, which doesnāt have a heat pump, I noticed that when stationary, even in subzero temperatures, the car was only consuming between 1 and 2 kilowatts, with the occasional blip up to 3 kW, to keep the cabin and battery pack warm. So, even with only one third battery charge, 20 kWh, you could expect that car to keep you warm for
at least 5 hours, probably more, and you can easily stretch that just by turning the temperature
down and bundling up. Aside from winter, letās talk about what
other things affect your range. Earlier I mentioned that highway driving is less efficient than stop-and-go. Why is that? Well, with all else being equal, the single greatest factor to driving efficiency in an EV is your average speed. See, as you go faster, your car has to work a lot harder to push itself through the air. As a matter of fact, wind resistance and rolling resistance are essentially the only two things working to slow your car. Both increase with vehicle speed, but the drag created by air is not a linear function - as a matter of fact when calculating drag force, velocity is squared. So the faster you go, the harder a motor needs to work to push your car the same distance, and the effect gets worse as speed increases. Thatās not unique to EVs, of course. The same goes for any vehicle. But because the vehicle doesnāt use any energy when itās
not actively trying to push itself forward, you donāt get the waste of an idling engine. Even better, regenerative braking allows the car to get back most of the excess energy it used to accelerate from a stop when you return to a stop or slow down. Regen braking and zero idling waste make average vehicle speed essentially the only factor when it comes to energy efficiency. That is of course until we talk about wind. When youāre driving into a 10 mile an hour headwind, the effect of the wind is exactly the same as if you were driving 10 miles an hour faster than you really are. So wind conditions can rather drastically affect your driving range. On the road trip I took with Aging Wheels, we started our journey driving right into a nasty headwind, which reduced my carās efficiency from my typical average of 3.2 miles per kWh down to 2.4 miles per kWh. That was about a 25% increase in power consumption, and
thus resulted in a 25% drop in range from what I was expecting. In the end, this wasnāt a problem. Our route planner was being so conservative that we actually hit
the expected energy consumption almost exactly. And, hereās the other thing to keep in mind, if we absolutely needed to stretch our driving range thereās a really easy way to do it: just slow down. Thanks to that head wind, we experienced a range similar to if we were driving perhaps 90 or 95 miles an hour, even though we were really doing 70. While itās obviously annoying, dropping to 55 or 60 miles an hour would immediately have stretched our driving range considerably. So if all else fails, just slow down. Wind, average vehicle speed, and cold weather
are definitely the three biggest factors that will impact your driving range. But what surprised me the most when I started driving electric
was the impact of wet roads. Light to moderate rain doesnāt have too much of an effect, but when itās raining heavily enough that water is pooling on road surfaces, the extra drag created as your tires work to push it
out of the way is much more substantial than I would have expected. The absolute worst driving conditions when it comes to range are windy wintry days with slushy road surfaces. Add enough snow to keep you using the defroster
and you have a recipe for heavy range loss. Itās for these reasons that I feel we need much more density in DC fast charging options along highway routes than we currently have or are planning for. 50 miles apart is a decent target, and realistically even if I had a 75% range loss that would at least keep me on the road. But since driving range can be less predictable than is ideal, I hope to see far more DC charging options. If we keep driving cars on long trips at the rate we do now, we are eventually going to need as many charging stops along the highway routes as there are gas stations today. So thereās a lot of work to be done, to be sure. But perhaps my favorite thing about electric cars is the chicken-and-egg problem that normally comes with changing fuels is sidestepped. Those of us with home charging can get an electric car right now. It can take care of all of our daily needs and we donāt need to rely on public charging. And now that those vehicles exist, thereās a market for DC fast charging on highway routes. And when owners of todayās EVs sell them, less expensive options are on the market which encourages more adoption, and that will increase pressures to install charging infrastructure at apartment complexes and other hard-to-serve areas. Thereās a lot of work to be done, and many would argue that electrifying cars is just trading one problem for another. And to be honest, Iām increasingly upset with how car-centric our infrastructure and cities tend to be. But frankly, right now I need a car. And Iām not gonna poo poo harm reduction. The fact is going electric is really quite easy once you understand the ins and outs. If you can run a wire to use a dryer you can charge a car and go real far. Now we just have to do it. Thanks for watching. ā« energetically smooth jazz ā« Hey, Iām gonna be recording an unscripted video on my second channel talking about some potential options for multi-family buildings
and other finicky-to-serve places. Clicky thing, link below, you know the drill. How to choose the right one for yourā¦ *sigh* didnāt get through the FIRST LINE! Here we go. What is happening? What... what is that? Oh, itās velcro from the thing. Got it. Any car will workā¦ eh, Bah! PEH! PLEH! BAH! ā¦with different pack sizes to chooge from. Chooge? But again, getting my getting aā¦ getting myself ahead of here? It puts a lot of wear and tearā¦ oh no, I changed that on purpose you dingo! I hope those of you who like That Company aren't too put off by my suggestion that folks install a J1772 charger. It just seems to me that there's more value in the standard which benefits from industry cooperation than the one made by a single, if currently dominant, player. Don't like putting all me eggs in one basket, y'know.
Enjoyed the subtweet about 2-minute water boiling in 240V land.
I've actually been wondering what it would take to get 240V circuits in the kitchens for all new construction in the US (and not just the oven). I think trying to fully switch North America over would be ridiculous, but kitchens have a few things that could really benefit from having the extra power a 240V, 20 A circuit could provide. Maybe not enough to retrofit every kitchen, but if you're running electric lines for new construction anyway, why not? (I also think all new construction should be fitted with 240 V for ovens, even if they come with a gas oven.)
The only thing stopping me getting EV in the UK is that my home is a terraced house , park the car outside the house on the street . I don't think having a cable from house over the pavement to the car would be sensible or legal haha š .
Holy cow, why do you have so many 15 and 20 A breakers? Is it a Midwest thing? Could you run a space heater on every outlet?
Marvellous video, what a treat!
This is the video thatās perfect for my 70yo parents struggling to make sense off the EV market. Thanks so much for making it!
This comment may apply more to the Extras video, "EV charging thoughts for renters, multi-family buildings, on-street parking areas, etc.":
When he talks about carrying a (hardware) fob so you can identify yourself for chargebacks, there is already a standard (ISO 15118) which allows for your identity/credentials to be store on the car itself, so that when you plug it in, the charger (network) knows who you are and where to deduct funds for. No further action than plugging is needed.
For communication between the charging station (EVSE?) and the back-end equipment see OCCP:
And IEC 63110:
Then there's IEC 61850, which kind of a 'smart grid' protocol, which would allow chargers to ask the building or even sub-station is available for charging, and use available capacity to feed more chargers. So if a (apartment, condo) building has a capacity of (e.g.) 1000A, at 6 PM / 18:00 everyone is cooking dinner and there isn't much 'spare' capacity to do dinner, so the sub-station monitoring equipment will tell the building chargers to use less. But at around 8PM/20:00 the demand from the rest of the building will be dropping off, so the main building sub-station will tell the car charging (sub-)sub-station that it can use more power (up to its installation limit).
Further, these communication protocol allow chargers/EVSEs to talk amongst themselves, so if a there are car(s) that are at (say) 70% charge state, but a new car pulls up with only 20%, the chargers can 'decide' to give the new vehicle more juice so that it can bulk charge up faster, while the already more-full vehicles getting dialled back to a trickle. This can be done even in a home/residential setup: see Example 2 at 38m00s in the above video.
So, earlier this summer we more or less decided to look at an electric vehicle to do our daily commute in. (actually daily school shuttle, but same diff).
That said, I really still don't like several things about electric cars specifically, and modern cars in general:
you can turn off an internal combustion engine car and work on it without worrying about being killed by massive, still charged battery packs.
no electric car I've seen has the equivalent of industrial machinery's 'e-stop' big red button under a cover. Why not? Does no one remember this?
https://www.nbcnews.com/businessmain/toyota-settlement-over-acceleration-problems-top-1-billion-1c7659318
https://www.transportation.gov/briefing-room/us-department-transportation-releases-results-nhtsa-nasa-study-unintended-acceleration
Anyone have any thoughts how to live with the above issues?
Thanks, -- Pat
I literally had an electrician over for an estimate on a 240v 40a line to my detached garage. As soon as they left I opened YouTube and the video had just been posted lol.
I'm in the Midwest as well and I'm terrified negative temperatures would make charging off 120v a moot point. But that's only 2-3 days a year and shouldn't be a big problem in the day time / sheltered from the wind chill... I'm not as lucky on the breaker front, I'll need a newer one (with more slots) and that was quoted at $1,800 for parts and labor. The 100ft run to the garage was another $1,500.
And there aren't many electricians these days willing to do residential work. They'll still have it advertised on their website but once you call the voice recordings usually say "we don't do residential at this time"...
For people still on the fence, possibly due to lack of faith in their local power distribution or who frequently drive long distances and doubt their ability to find fast charging when needed, do you think plug-in hybrids are still a good compromise? I think I want my next vehicle to be full-electric, but a lot of my friends and family are still either skeptical or are deep into the "electric is worse" propaganda.