RockShox Fork - Overhaul, Rebuild. Self maintenance at home

Video Statistics and Information

Video
Captions Word Cloud
Reddit Comments
Captions
If you have a maintenance table, it is best to mount the shock on the maintenance table. oil pan ready 5mm wrench Loosen the bolt half way the opposite bolt is the same Position the shock horizontally The shaft and lower leg need to be separated. Gently tap the loosened bolt with a hammer so that you can feel the bolt go inside. Remove the bolt. At this point, oil may come out. The crush washer is pressed a lot. Separate the lower and upper legs by lightly pressing them with your hands. The lower leg is the part with the decal, and the upper tube is the part with the silver tube Wipe the oiled area with alcohol. Be careful when using alcohol on the matte paint part as it may cause whitening. isopropyl alcohol 24mm socket The rebound damper has an O-ring inside so it doesn't come off, so gently tap to remove it. Turning it upside down takes less force. The oil inside is also cleaned with alcohol Use a long pole and dust-free cleaning cloth Remove the opposite preload cap Bottom-out anti-rubber removal When the shaft is raised from the bottom, the spring comes out from the top. Clean the inside with alcohol and a cleaning cloth After cleaning, apply a small amount of grease to the top cap thread. Remove rust from stanchion tube. Use Juice Lube jl69, or wd-40 Partial rust removal and old dirt removal It is possible to remove rust with a brush, but do not overdo it as the tube may be scratched. Remove the spring grease and apply new grease. Spring shaft cleaned with alcohol Clean the rebound damper with alcohol too. If there is a problem with the O-ring, use a RockShox service kit to replace it. When re-installing the O-ring, soak it in 15wt oil or apply a small amount of sram butter. When the preload cap is turned, it presses the spring to make the shock absorber stiff or soft. Clean the dirty part of the dust seal with a degreaser. Cover the lower leg with a suitable size spanner and cloth, insert the spanner inside and apply force to separate the dust seal There is a special tool for re-installing, but I decided to use a 32mm socket instead. Apply a small amount of sram butter to the inside of the dust seal 15wt Viscosity RockShox Oil 20ml Injection into the lower part of the spring shaft. Inject 150ml of 5wt viscosity oil to the side of the rebound damper. (For products with turnkey, only 93ml is injected.) Replace the crush washer with an inner diameter of 8mm, outer diameter of 11mm and a thickness of 1.5mm. Assembly is the reverse of disassembly Insert the spring shaft first, then the long spring. Tighten the preload top cap to about 6.7 N.m. On the other side, put the rebound damper, For products without turnkey, install the lower leg and add oil. Tighten the bolts in the part with the rebound damper to 6.7N.m. 20ml of 15wt viscosity oil is injected into the spring side with the preload cap. Same tightening to 6.7 N.m. When the installation of the lower shaft bolt is finished, pour oil into the rebound damper side. 5wt 150ml The cap locks at 6.7N.m with a 24mm socket. Top tube protective spray application. RockShox turnkey products are slightly different from non-turnkey products. The decomposition process is the same as the previous process. Remove the snap ring on the lockout knob. 24mm socket Compression damper removal. rebound damper The top tube rebound damper part of the product with turnkey has an O-ring on the inside. Products without turnkey do not have O-rings in this part. Compression damper with lockout function If you turn the lockout button to lock it, the hole is blocked and the stick does not go in. You can use the rebound function by turning the plastic knob at the bottom as a rebound damper. Clean the dust seal with degreaser. Put the rebound damper first, then pour 5wt 93ml oil. Then put in the compression damper. Inject 15wt 10ml of rebound damper on the lower side and 15wt 20ml of spring on the opposite side
Info
Channel: COMET RESTORATION
Views: 2,306,462
Rating: undefined out of 5
Keywords: 자전거리폼, 자전거 리스토어, Bike, Bicycle, sepeda, restorasi, sepeda restorasi, restoration, old and rusty, old restoration, Bicicleta, restauração, restauração de bicicletas, restauración, restauración de bicicletas, MTB, fixed gear, bike restoration, restoration car, motorcycle, motorcycle restoration, rockshox, rockshox dart, bike shock
Id: Yuh5CYuzDMc
Channel Id: undefined
Length: 14min 53sec (893 seconds)
Published: Wed Dec 22 2021
Related Videos
Note
Please note that this website is currently a work in progress! Lots of interesting data and statistics to come.