Making tenon joints with the Moving fillister Plane

this morning at the northern would show we just can't have a look at using our new moving tell us the plan to make Santana these four Royals for coffee table we're going to put the mortise and tenon on all four rails at one go these have been cut to length but for a perfect finish you need to have a very square so I'm gonna use my trying pine square the inside this is red cedar on planing so doing end great work you need the play to set berries we do a harder wood you accept this blade perfectly square that just go through watching us where the enema Piper riles directly next time glue is to lie upon your bench is where it's important Adventures dog heel which is 90 degrees to this dog ball here with the tower voice finally may hold one end as long as our proper spacing science and that will help square this up yeah right so make sure that you know if you put these through it yourself they should be that makes it nice and flat now also to help hold things extra to be placed don't call here hold fun and you'll find in this position in relation to your tail boys this is a pretty handlebar support that then tightens everything down Mike's level on the bench ready to do a job and get more accuracy into your work mr. fine know what I'm gonna demonstrate my horse antennas all in one go the speech processor the moving filter has an adjustable fence and it has a scale on the fence front and backside and get them perfectly now they're in millimeters or you can get them also in imperial we also have a scale it's a bit hard to see but there's a scale on the side of the plane so that you can set the correct depth of sharp immobilizer the skew angle and it's important you keep that angst so that when you put the blade in two edges parallel to the sole to cut a square rebate yeah it has two little slots in the back of the blade and they fit over a pin in the adjuster that's so that comes in from the bottom slides over the top of the pins and locates on the pin so that the blade will move up and down by the adjustment here bring your this knob here will tighten up like a wedge and that holds the blade in position so just bring it down self just starts to engage blade but you can still move it fairly freely to position it correctly so with the plane sitting like this it's really easy just to use your two hands tool actually adjust it so you can just see a whisper of blade outside in actual fact it lines up with the nikah play and it's parallel with the sole then once you've got that there lock it down a bit tighter and adjust the depth to exactly the way you want being cedar I can take a breeze we do cut then lock it off the maker has a tiny little adjuster the softer wood you can go deeper with uniquor the in essence the nikkor cuts in front of this play so whatever the depth you set the this supply it has to be just a little bit less now these boards 19 mil thick stick and I want a 7 mil tongue for my tenant so I'm going to set to 90 my 7th 12 5-12 is 6 sort of takes 6 millimeters off each side so I'll set my depth stop 6 Mellon and I want the talent to be one inch wide so I've worn my fencing under the plane using a two knobs on this side it's a left hand thread so each one of these increments is five millimeters so I'm going to stop at the fifth one of those actually on my 26 millimeters once they're both scales are people I'm now ready to play in my face of water it's really important as you're the person operating twice that defense sits squarely against the end that's what at the end of the day was giving us where's toy the palm of your hand is where the power comes from so you must have your power on there locate your fingers somewhere around the adjuster and use the fence grab the plane like this we'll catch so that you can push the fence against the end of the water flying a while back and sure you're starting square so just have a look from the end and ensure you stay up against the fence so that the verdict the wall here to stays vertical taking a really nice shaving but it's not too hard to push if you work in a part of woods just reduce take another sneak peek it's usually pretty obvious if it's getting out of square it looks good there and we're starting this close for our depth but fine stop cutting and that's that half the most technologically it's been cut to treat the bullet straight everything feels good level it means I can now cut seven the other saw sign against makes our heart up against the make sure you let the shavings come out if they pack up in the throat they will stop just check running pretty square they're getting close now and the depth stop release the ball past and they have very very neat Tana night so if we were to put on a piece in you can see the crispness Oh George it's perfectly square dude if this is both shoulders exactly parallel to each other nice smooth finish that should fit straight into your tenant if you imagine things up correctly do the other end and you've got all your tenants done into making in this tool can also do any size rebate along the grain and price and shortly we'll have a look at doing a shorter tenon sorry

Channel: undefined

Views: 13,509

Rating: 4.9515152 out of 5

Keywords: HNT Gordon, Moving Fillister, Tenon joints, woodworking, Moving Fillister Plane, Melbourne Timber and working with wood show, across the grain, along the grain, woodworking joints, woodworking planes, Mortise And Tenon, Wood

Id: NDphr-AWEC8

Length: 11min 10sec (670 seconds)

Published: Thu Oct 01 2015