Incorrectly Wired Outlet Found In Newly Built Home

how's it going you guys it's Scott with everyday home repairs and I want to run you through three mistakes that I ran across when swapping out a receptacle at a friend's house this past weekend so I was over there and they said Hey in the basement and we have a receptacle that has failed can you take a look at it went down there and it was kind of the classic scenario it was a 15 amp receptacle 50 Cent uh super cheap residential grade it had was common to have a vacuum plugged in so high frequency of plugging in and unplugging and also a pretty heavy load from the vacuum and space heater has a space heater plugged into it so that receptacle actually failed I didn't save it I should have saved it but when I went to rewire a new commercial grade receptacle three things popped out so what I did is I took the same type 50 Cent residential grade receptacle I wired it the same way it was wired and I'm going to run you through the three things that were mistakes or against best practice so let's start with number one now number one is something that I did for years and didn't really pay much attention to but when you look at the side profile of this receptacle you see these unused screw terminals so under neutral side and on the hot side so the problem with that is any unused screw terminal should be tightened down securely and why is that because you can see the profile of the housing the leading part that would connect is the actual terminal the hot terminal that's not ideal especially if you have metal boxes or any other wires or anything that I could contact so what you do is you just tighten down those any unused tighten down any unused screws on both the hot and neutral side just as best practice so when you do that the nice thing is if we look at that profile again now we have our housing our housing is that Leading Edge now your screw terminal that has a wire underneath it that has the shepherd hook underneath it that's still going to be probably flush with your housing but this is much better than having those screw terminals kind of dangling out there so that's number one tighten down any unused screw terminals now number two is similar to a topic that I discussed in a video I did over a year ago and that link is right here if you're just starting off and getting into electrical work you want to swap out a few light switches at your house or maybe a few receptacles install one with USB this is a good place to start it'll run you through more Basics and it talks about the same mistake or same issue that many professionals try to steer clear of and if you can guess that is using these push in connectors so you can only put for you're only supposed to put 14 gauge wire into that but these are notorious for being a common failure point and from the hundreds or even thousands of comments that I have received from licensed electricians on my past videos and for one thank you thank you guys for giving feedback I really appreciate it and I'm trying to condense that down and then provide it back to the viewer so we can all learn I do want to be clearer that push ends are not against NEC or not against electrical code and are also certified by the underwriters lab or UL you'll see that little circle with the UL stamped on a lot of components that means that it's past the industry standard for safety and it has the certification of UL so push in is not against code not against safety certification but from the Professionals in the field and myself included not being a professional in terms of failure points push-ins are more common as a source of failure opposed to a a properly installed wire in a j or Shepherd hook underneath a screw terminal so that is the second of three mistakes that I found on this receptacle in the last one so you can see I have three neutrals and three Hots going into this receptacle now that is definitely not best practice this is a mistake that I've made in the past in fact one of my former videos I put two Hots and two neutrals in a back wire so now push in a back wire terminal and and people would ask why and then other professionals that said hey you should really do a pigtail so taking their advice let me show you how to create a pigtail I'll remove that same receptacle that I got the feedback on and remove the two Hots indicated by the red wires and two neutrals indicated by a white wires now I'll go ahead and take a little more insulation off getting ready to create the pigtail take it off the hot side and off the neutral side then I'll actually create pigtails of more than six inches in length and then those will be twisted together with my other Hots so I have a black indicating the pigtail hot coming together with the Reds that are the hots wires coming in twist those together with some heavy linesman's pliers or Kleins and then trim off that edge then introduce the wire nut tightening it down on that hot side and there's the pigtail I'll do the same over on the neutral so bringing together the three wires clockwise rotation twisting those together and then trim up that edge clean it up a little bit tighten down the wire nut okay so now you have your pigtails additional feedback specifically on this install was to use that box extender because this is wood paneling and there was exposed wood paneling to the sides of the outlet and that is actually against code so I just put that box extender and now I'm wiring the pigtails into the back wire again these are not cushions it's back why because this is a commercial grade receptacle that has that so you'll tuck those wires back in and then you'll just have the three coming out this is again 12 gauge not 14 gauge so a little tougher to work with but not too bad and then the boxing Center does come with longer screws so I'll cinch those down get my face plate back on and now we're good to go so that's how you create a pigtail and you can see that's a much better approach than this jumbled up mess here you know tie everything together back in the electrical box and have a six inch or more pigtail coming out one hot one neutral one ground and it's just a much better approach as always get down in the comments let me know what you guys think what questions do you have is there anything I missed I always appreciate your feedback now this example was on a two-year-old house newly built past all the inspections and had quote unquote professionals installing these receptacles so you can see there's a wide variety and it pays to educate yourself because no one's going to care more about your project or your home than you with that said if you're taking on electrical projects be safe it is up to you to work safely and also up to you to follow all local and National codes and regulations now before you take off if you're not subscribed already don't forget to hit the Subscribe button down below and so we have multiple videos coming out per week to help you with hairs and improvements around the house and we'll catch you on the next one

Channel: Everyday Home Repairs

Views: 2,702,068

Keywords: wiring an outlet, wiring mistakes, everyday home repairs, electrical code

Id: _rRa_CedJ38

Length: 7min 33sec (453 seconds)

Published: Mon Feb 15 2021