Как устроен автомобильный двигатель

The engine block is the backbone of any automotive internal combustion engine. Plugs of technological openings and plugs of a cooling jacket. Oil channel plug. In this model, the cylinder liners are removable. Copper pads. Head studs. Crankshaft studs. Crankshaft. Crankshaft oil channel plugs. Indigenous liners and tubular pins. Each bushing has two holes for oil supply. Also on the liner there is a lock, this is a persistent ledge that prevents the liner from turning or moving. Yoke or main bearing caps. Thrust half-rings of the axial displacement of the crankshaft are installed on the central yoke. Bracket for oil pickup tube. The bolts are tightened in the direction from the center and to the sides. Pistons. Oil ring. compression rings. Installing the piston on the connecting rod. Piston pin. Retaining ring. Connecting rod bearings and bolts. Yoke of connecting rods. Gasket and cover of the rear oil seal of the crankshaft. Stuffing box. Timing chain drive star. Drive gear for oil pump and distributor. Timing chain guide. Front crankcase cover. Oil pump gears. Oil pump bypass valve. Oil channel plugs. Front crankshaft seal. Valve train chain. Cooling jacket cover. Crankshaft pulley. Oil pump intake pipe. Pallet. Coolant pump. Upper oil filter cover. Oil channel plug. Oil pressure sensor. filter element. Oil filter bowl. Cylinder head. Valve guides. intake valves. Exhaust valves. Support washer. A pair of springs with opposite coils relative to each other. Valve disc washer. Valve plate. Rusks. Rocker. Washers. Remote bushing. Spring. Rocker axles. Plugs. Distributor bushings. camshaft. Head cooling jacket plug. Same plug on the other side. camshaft retainer Timing chain tensioner sprocket. Valve tips. Cylinder head gasket. The nuts are tightened from the center to the sides, while in a cross order. Distributor sprocket. Before screwing the sprocket to the camshaft, it is necessary to set the camshaft and crankshaft according to the marks. With correctly set marks, the piston of the first cylinder - occupies the top dead center. In this case, the marked camshaft is in a position in which both valves of the first cylinder are closed. It remains to adjust the sprocket on the pin and fix it with bolts. Tensioner plunger. Plunger retainer. The plunger is fixed with a bolt. Tensioner spring. After fixing the front cover of the head, the plunger fixing bolt is released. The plunger is released, which, under the action of a spring, tensions the chain. After that, the plunger must be fixed again with a bolt. This will prevent premature stretching of the timing chain. Back cover of the head. Fuel pump. Pump drive pusher. thermostat housing. Coolant temperature sensor. The locking element of the thermostat. The top cover of the thermostat housing. Valve lid. Intake manifold. Carburetor. Air filter housing. filter element. Flywheel. Starter. An exhaust manifold. Drive distributor and oil pump. Trambler. Spark plug. High voltage wires. Cooling pump pulley. Ear mount generator. Cooling impeller. Alternator mounting bracket. Generator. Pump and alternator drive belt. Dipstick for checking the oil level in the crankcase. Tube vacuum control distributor. Branch pipe for neutralization of crankcase gases. Crankcase ventilation pipe. Fuel pipe. Pipe between pump and thermostat. Pipe between thermostat and intake manifold. Engine cooling radiator. Lower and upper radiator hoses. Coolant expansion tank. That's all. Thank you for watching. Until new videos.

Channel: Sanya Tsvay

Views: 6,084,545

Keywords: Двигатель, автомобиль, 3д, м412, москвич, Engine, car, 3d, m412, Muscovite

Id: PXDFuIMHNZw

Length: 18min 59sec (1139 seconds)

Published: Thu Feb 16 2023