Engine cooling system / how does it work? (3D animation)

[Music] engine cooling system the combustion of the fuel air mixture results in the release of a huge amount of heat the engine will quickly overheat and fail if not cooled therefore Engineers designed an engine cooling system this system is primarily required to keep the engine cool and that its optimal operating temperature it is located directly within and around the engine you can see the key components of the cooling system let's review the liquid cooling system in detail gradually complicating the layout heat is removed from the engine via cylinder block ducts and cylinder head ducts these ducts known as the cooling jacket are filled with coolant the cooling jacket is situated around the engine cylinders and serves the primary purpose of removing heat from those cylinders the coolant doesn't stay in the same place instead a water pump keeps it circulating in a closed loop in turn the pump is normally rotated by a belt drive that is powered by the crankshaft this type of pump is known as a centrifugal pump the liquid would be cooled too slowly in this setup causing the engine to overheat therefore the radiator cools liquid through a high efficiency heat exchange process the radiator is made up of two tanks with an inlet pipe for heated liquid and an outlet pipe for a cooled liquid the tanks are linked together by a system of tubes fins are added to the tubes to improve heat transfer capacity these systems are referred to collectively as the radiator core a drain valve is normally located near the bottom of the radiator the radiator is also equipped with one or more fans that boost the flow of the air traveling through the radiator in case the system fails to cool the liquid to the proper temperature when a specific temperature is surpassed the fan is turned on using the radiator coolant fan switch or more commonly the engine coolant temperature sensor the sensor also displays the current coolant temperature to the driver of the dashboard typically the sensor is positioned near the engine coolant Outlet it should be noted that the cooling system is a sealed system when the coolant is heated it expands causing the pressure in the system to rise this is required to raise the coolant's boiling point however access pressure must be released to prevent system harm one of the ways to do it is to use a special pressure cap on the radiator when the maximum allowable pressure is exceeded the cap opens enabling coolant to escape into the expansion tank when the pressure decreases the liquid is pulled back into the system this design excludes pressure in the expansion tank the tank stores at coolant Supply and has free space for liquid expansion the expansion tank also features coolant level indicators and can be used to refill coolant as needed this is another design with no radiator cap pressure relief is provided in this case by the expansion tank cap which manages the pressure level in the system in a similar manner by releasing and sucking air this system is already capable of cooling the engine however due to the continuous Passage through the radiator it will take a long time to heat the coolant in this instance and maintaining the appropriate working temperature will be a problem this will result in increased engine wear and excessive fuel consumption to prevent this the system is equipped with a thermostat the thermostat divides the system into two circuits a longer one that uses the radiator and the shorter one where the radiator is bypassed when the coolant temperature is low it will circulate around the shorter circuit bypassing the radiator thus allowing the engine to reach operating temperature more quickly when the temperature hits 82 degrees Centigrade the thermostat valve gradually opens and the hot liquid mixes up with a radiator cooled liquid from the longer circuit which ensures that the temperature is balanced if such mixing is insufficient and the temperature continues to increase at 93 degrees Centigrade the thermostat will shut off the shorter circuit and fully open the longer circuit allowing the entire volume of the coolant to circulate through the radiator you can now see a fully operational cooling system however it is missing one critical component the car can do without it is the heater core in this layout the heater core is integrated into the cooling system separately from the thermostat the heater core harnesses the heat from the coolant to heat the vehicle's cabin the cooling system is now complete there are other more complicated layouts they may contain two thermostats electronically controlled thermostats as well as more complex cooling circuits that keep the EGR system turbocharger throttle intake manifold and automatic gearbox oil at the appropriate temperature it should also be mentioned that the system employs a special coolant with specific chemical features such as anti-corrosion anti-cavitation or non-freezing properties this concludes our review

Channel: CARinfo3d (En)

Views: 502,004

Keywords:

Id: k0ovUHEOtyE

Length: 6min 51sec (411 seconds)

Published: Fri Mar 17 2023