EEVblog #1265 - $53 360W Lab Bench PSU!

Video Statistics and Information

Video
Captions Word Cloud
Reddit Comments
Captions
hi in previous videos we've taken a look at these little Rd tech power supply modules and I'll link in the videos at the end if you haven't seen it but they've been incredibly popular and I've been watching over the years as they've been developing better and better power supply products to the point where they practically own the market for these little power supply you know stand-alone modules and they're really quite remarkable so I thought I'd take a look at the latest one it's the ID six double O six one it's like a front panel type solution like this and I have the optional Kayson so we've done several videos on this companies our products before they're not actually our D tickets hen's you reading technology but I'll continue to call them our D tech anyway that's the website will link them in and they're over on Aliexpress so I'll link them in down below I do believe other sellers like resell them but I'd recommend buying directly from the Rd tech arm Ally Express store this one in particular 360 watt output power 6 amps a maximum output current zero to 60 volts output and a it's just a buck converter so you need to put you can have anywhere from 6 to 70 volts of DC input and that will then give you a corresponding range just I believe 1 volt below whatever input voltage you feed in so that's really quite remarkable in like a you know a three under power supply switching of course you can't get any linear stuff in something this tiny but this one goes for 53 dollars without the Wi-Fi module or 57 dollars that's Yankee bucks with the Wi-Fi module so you might as well get the Wi-Fi module with it and it comes with two optional cases I've got the big one which we can build in our own power supply into power supply is separate and it comes with all the bits the case is $32 for the long one or twenty one dollars for a shorter case like this it just has our binding post terminals on the back as we've seen in that previous videos and you can power them from any external power supply you have available but you know I want something to be nice I sprung for the bigger cases but as I said you can use any power supply you can salvage out of any old gear or anything like that from 6 up to 70 volts obviously if you get a 6 volt one you might be able to get 5 volts out of it but that's all you can get so it's not a true Sepik converter one where you can feed in 6 volts and then get 0 to 30 volts out it's only a buck converter now I do actually have a power supply come in but it's in the mail let's take a look inside all you get is just this info card you can go download the datasheet that's great I don't like having manuals in there that's just yeah they're pointless these days and we've got our little module isn't it cute look at that absolutely fantastic for under 60 bucks u.s. that is a complete 300 plus what switching power supply with the user interface and everything we'll take that off so there's a little Wi-Fi module that's only 4 bucks extra complete no-brainer whoa when you get it this is a temperature probe adapter which we plug into the board and we got a spare little surface mount fuse and a couple of spade lugs that we can then plug into our whatever power supply we choose to use yes so this thing really is quite impressive oh I love the buttons it does have a knob that's got indents on it it's push abort yep I haven't looked at the user interface yet it's got an output on/off button it's only a single output and one of the interesting things is that the first glance you might think this Center terminal here is an earth terminal like mains Earth terminal I should typically find on a metal chassis you know LED power supply because it's green and well that makes sense but it's not look at the little indicator there this is actually for the battery charging mode so in battery charging mode this is the negative terminal and this is the positive battery charge in terminal and they've color-coded a green why we've got USB here presumably you can do like firmware updating stuff I set V set memory well looks like we've got nine different memories there fantastic and a nice new power button and the buttons light up and a reasonable size display and that just snaps into the front like that I won't do it now cuz then might be hard to get back out but yeah they've really upped their game over the years of course I've done the very famous video where one are there are power supplies caught on fire because they had a shorted out a ceramic cap but they you know they fixed that pretty quickly because it was just a physical location thing a link in that video it's very it's quite educational anyway there's a little socket for our fuse so it looks like we have a little tiny SMD output views that's nice anyway nice honking relay there and I'm not sure if those caps are in parallel or not you shouldn't have that much capacitance on the output of a lab power supply but anyway I'm eighty volt caps I'm ECD a brand I don't know anything about them really not a huge fan on this thing but it does have a fan it will be temperature controlled a big step freestanding honking resistor there so that's interesting another fuse up there so that'll be our input so we've got an input fuse and an output fuse here this goes over to our temperature probe you I won't try reverse engineering this of course it's not open source they don't release the schematics but I believe us some people have reverse-engineered the Rd tech ones did I even do it in a video I think I anyway we've got our main our display a processor board down here it looks like it's got an arm flavored processor down there can I get that board out I'll try no it doesn't look like I'm going to be able to get that out because of the binding posts that are soldered in there so unfortunately and that's not going to work anyway I do like the binding post there they kind of like Oh remind me of like the agile at once the hole in the side looks adequately sized those they've got the middle on the bottom they don't have and some metal on the top like that so they're not too bad certainly seen a lot worse than that so I don't mind those the general feel and quality of this thing you know it really is quite remarkable especially for you know a sub $60 power supply and this is completely standalone like you can just buy this the minimum for 50 to you dollars feed-in whatever voltage you wanted to hear from any power supply you don't need any case you could just sit it on your bench like that and you're gonna have a working power supply up to 300 watts or the capability of your input power supply so yeah that's just like unbelievable how the market has just you know they've just blown away this power supply market so anyway our purse in the pudding so 300 watts it's a 95% efficiency you'd be talking 15 watts in this thing and of course you'd need air flow to I get that out but yeah it's it's certainly doable sorry it's a 360 watts anyway I'm here's some basic specs as I said does 0 to 60 volts out it depends on the capability of power supply 10 millivolts are resolution output current setting 0 to 6 ends with 1 milliamp resolution that's absolutely fantastic apparently it's got a battery charging mode as well with 10 millivolt resolutions anyway output voltage accuracy is claimed at 0.3% plus 3 output current accuracy 0.5 plus 5 that's plenty 100 millivolts some output ripple so of course that'll change with the output current of course so it's not the world's best low output ripple power supply but that's not its job it's just diet job is to just be a cheap general-purpose high power lab power supply and it can do capacity and energy measurement as well I want to check that out and that's absolutely fantastic it claims there's a 2 percent error on that and a 1 volt drop that's why I said if you feed in say a 24 volt if you've got a 24 volt power supply pair in this thing you should be able to get to zero to 23 volts it doesn't come with a backup battery though which is interesting than to be for your real time clock so not necessary for general operation but if I've got one I'll whack it in there so we've got the optional Wi-Fi module here so we'll just work that in there make sure the pins are lined up and Bob's your uncle we're good to go sorry our temperature probe that'll go in there but all we do is just feed in and power supply into there and it'll do the business so I'm gonna hook up my external supply here which is on only 188 what capable so we can't push it all the way unless I parallel various supplies in these are not the proper cage clamp ones there the lever ones move you what do you expect for the price right so we should now have a fully working power supply and yes you could actually power this from batteries and you could and charge in tech are stuffed into this case if you wanted to build a portable power supply or you can even build into your own custom case whenever you want to do and the bench supply is on but the power supply is off just residual it's our drawing 611 milli watts there so let's turn it on tada see it boot up right and DC power wow that's really quick booting isn't it and the quiescent supply nine hundred and fifty million watts or so the screen is really quite good even at a high angle like this quite readable so it's all color coded on the sides quite nice there's not much glare on that of course if I hold it and put it up to the lights you can see my lights there but anyway yep that screens pretty good no workers and it's a pretty info dense display look at this so this is our output voltage of course this is our output current showing zero because that's not the set voltage and our output power like this so three decimal places on the current as we saw before in the specs 10 millivolts resolution for voltage and 10 milliwatts resolution for the power there and we're in constant voltage mode it's showing that we're using em memory address as zero there so it's got actually 10 memory positions does it and don't know what the tick is anyway oh it's reading 26 degrees here in the lab but it's you know it's near enough anyway that's using that temperature sensor probe that's plugged into the back and milli watt hours there's our capacity brilliant showing our Celsius and Fahrenheit there now it's got over voltage protection over current protection I believe they're only like software protections as in the previous supplies I don't believe it's got proper hardware cro independent hardware crowbar protection self the software fails a locks up or does whatever then I don't think that's going to save your product from you know over voltage the whole idea if you don't know of over voltage over current protection let's say you're pairing up you've built your new SuperDuper expensive board and it's got $10,000 worth of parts on it which is not uncommon trust me I've worked on boards that have many tens of thousands of dollars worth of parts on and you cross your fingers and you pair up the power supply for the first time and you fight pairing your five volt rail from your bench power supply but oops you've accidentally set it to 12 volts or something like that if someone comes along or they knock the knob well you would set your over voltage protection to say five point one volts so regardless of you know we stupid marketing manager comes along and twiddles with the knob and stuff like that you don't want to blow up your tens of thousands of dollars worth of prototype hardware so that's yeah that's an idiot marketing protections mode okay it's currently set to Y five volts and six point one ants and our input there you go thirty 2.01 so it's measuring our input voltage very nice so let's turn it on there we go and it sort of like I don't know if it ramps up like that way after you get the scope on it but let's try that again it's ramping down so it's ramping I don't know if it has it a ramp like that it should be sharper of course but there you go it's set to 5.0 whoa we're getting 5.0 oh by the way I think they have learnt their lesson that using those multi-layer ceramic caps on the board that caught fire so look at that they're not using our mlcc's anymore using those leader ones those are film jobbies or are they leaders ceramics either way we're not gonna give a stress fracture problem that's for sure okay let's hook it up to the lab electronic load I just got a constant current of our one ampere so I will just switch that on just the default five volts out so point nine nine seven so that's accurate the voltage of course is drop you could see there that it was actually up yep it's spot-on there to the least significant digit no worries whatsoever and of course we're going to have some the reason this doesn't match is because we've got the loss in the little piddly cables here we could of course do a remote sensing so it won't be lazy Dave I will actually connect the external sense and by the way when you're doing the external sense make sure you get it around the right way I've got the sense this is the sense banana plug on the inner part of here if I actually put the sense on the outer part so you're not going to be including the the voltage drop across this banana plug here so just make sure that your sense one is in there like that and then your load on the other side it's a little trap for young players okay now I've enabled sense mode over here so it would have read the voltage from here instead of the input terminals so if we switch this on the voltage here should now match the one here because if there's no voltage drop across the lines cool so this is more than meeting its specs very nice so if I want to set my current all I've got to do is press I set here and you can see it put a little purple highlight there and of course you can move that digit like that all right so I'll set it to what six amps now so five volts or six amps there we go five point nine nine five point nine nine eight it's measuring bang-on and we're now joined 30 Watts from this puppy and when I switch the load off you can see that the fan to stop so it is certainly temperature control to switch it on and the fans going to be running but can hear a little were maybe but nothing offensive okay so I'm going to go into voltage set here I really don't like the the beat beat like that sounds like a Geiger counter or something like that anyway there's no real velocity control properly on here but of course if we want to go do our 30 volts we can just go thirty into like that and bingo straight up to thirty and another thing is unless you go into some sort of art mode none of these buttons will do anything and that's what you want these control shouldn't do anything unless you choose a particular mode so that's nice tell you what one thing I think is a bit of an oversight if you go voltage set okay and you want to go say 30 volts you have to be hit enter you can't just press that it doesn't work I would have liked to have seen into like it'd be the same and for those playing along at home for the efficiency at 60 watts with this voltage input because it could certainly change focus a bastard could certainly change with the input voltage you'd have to fully characterize this thing so it's only about eighty six point eight percent efficient so it's dissipating nine Watts this thing but it's not getting hot it's not blowing much at all inductor they're fine the heatsink can put my finger on that no worries whatsoever so that's that's doing hunky-dory now this case supports a couple of different art power supplies one of them is a standard 150 millimeter by 50 millimeter and my power supply just turned up today it's a mean well our SP 320 series I got it from far Nels and it's a it's a 320 watt job so not quite the 360 watt max capability but it was cheap and mean well or you know a reasonably decent brand power supply but as I said you could like salvage a power supply out of practically anything and whack it in this case it's it's big enough to do that you may okay it may not have the standard mounting holes like this one is going to have so this one was our 83 Aussie bucks so roughly about the same price as the actual unit itself but you can get cheaper on a try to get the recommended one from another Aliexpress store but they refunded my money and just didn't send it yeah you can get a much cheaper there there's tons of different variants of our power supplies out here this one has a little art temperature-controlled art fan and the case comes with all the mounting hardware the fan a little our fan temperature controller with a probe and all the cables and all the screws and all the mains connectors all pre-terminated and insulated brilliant okay a mini teardown inside this meanwhile power supply doesn't that look really good i Rubicon main cap down here very nice old-school dip and that Lynx look at this single sided as you'd expect it all looks quite nice lots of our liberal silastic down there and what are our output cups Nippon chemi-con output caps absolutely fantastic this is Bobby Dazzler for all you fan fan boys out there get it I'm here a week anyway um yeah this looks really top quality looks ceramic fuse they're worth every cent these mean well ones quite nice and is that a temperature sensor they're running off farther than primary side switching trainees I think it might be pro tip don't daydream when you're installing your power supply cuz you'll install it backwards don't well that went together nicely that's a beautiful build it's even got the standoffs built into there for the temperature controller which supports up to our six to 70 volts power supply same as the module itself and it comes with all the cables they're all pre done absolutely brilliant I don't recommend having them tinned like that when they go into the clamp connect this but the only thing you didn't get was a couple of shape proof washers which would have been nicer but yeah everything's just pre done don't disorder anything just screw it all in Bob's your uncle well they just a reminder if you do want a properly earth case not that this power supply has an earth terminal on it because as I said that one is not an earth terminal maybe you could add your own to the back or something like that if you're really wanted to you just have to remember to scrape off some of the paint on the bottom side of here because this case is earth but if you want it to go to here or you can add your own separate wire to proper earth like whatever okay so quickly before I put it in the case I just want to run some basic characteristic performance curves just to get an idea of the efficiency over various output power so I'll just start with our 32 volts cuz that's the maximum there and it might be a typical voltage for example 0 to 30 volt power supply and just a reminder it's taking nine hundred and forty odd milli watts quiescent okay I'm sure 150 watts output here and really there's the thermal the hot spot the biggest hot spot down there is like 47 degrees and I can I can certainly touch that with my touch the heat sink with my finger and I really can't you feel anything nothing on the inductor over here so and that's dissipating now there's six watts that's at 150 watts output at 24 volts so firmly it's okay but of course if you take it right up to it so 320 and I set it to 48 volts total so I've got them in series in there we go 48 volts input so that's going to be exactly the output of my mean world power supply but of course the thing about this is whilst it is a 360 what capable power supply really because of its maximum are 6 amp output current capability you can't really get that 323 60 watts unless you're at the extreme ends of the voltage and most people just aren't going to be powering things at 48 volts you know 50 volts a 60 volts so yeah you might have that capability but if you don't have the output current and then alright so you take all that data and bingo please excuse the crew D the model didn't have time to build a scale or to paint it the efficiency versus output current for a 25 volt output voltage for a 0 to 6 amps that they gave me 0 to 150 watts so that's you know typical of what sort of a maximum most people would use it at and I did it I got two characteristic curves for different input voltages so for a 32 volt input and for a 48 volt input this is the 48 volt input is the one that I'll be using with my mean will and you can put in a higher voltage of course but at a 25 volt output a higher voltage you're going to get less efficiency you expect a drop here there could be some inverse in the characteristic but that's unlikely generally a higher voltage you'll see the same curve again not sure what happened to this data point over here I entered my data correctly maybe I measured it wrong anyway there is a little step down here at our 4 amps which is rather interesting maybe it switches switching mode there the the controller at 4 episode that's interesting both of them showed that and you know it's a pretty decent efficiency so you know like 90 I 95 odd percent but the efficiency does drop with the output voltage so I've done another little short one where got down to like a like a maximum of 88 at 10 volts output but anyway you could do these characteristic curves for every single parameter until the cows come home but you know it's pretty decent I thought it was supposed to have a temperature controlled fan but like it's switched off like the unit is off and the fans going full blast and I can hear that sure I've got the lid off but still it's going like the clappers so I don't like that at all unless I don't know there's an internal jumper or something out and I maybe have to read the manual but I not happy with that it's constantly going alright let's check the ramp on time from 0 to 5 volts bingo there we go that's about that's 50 milliseconds per division so about 50 milliseconds there there's no a bad overshoot or anything like that so that's clean as a whistle all right let's try a 0 to 45 volts same time base there we go exactly the same but you'll notice if we switch it off it is reading on the output terminals look how long it takes for those output caps to discharge so yeah large output capacitance as I said not ideal for a LED power supply because when it goes into constant current mode those caps can potentially deliver over current so yeah gonna be careful of that and off let's see how she ramps down I mean we've only got the the 1 Meg load on the import bingo there it is ramps right down it's you know it's clean but yeah take some oil check this out we've got common mode noise to buggery and yeah it's not great is it and I've done whole videos on that No well unfortunately I'm now using an isolated scope and it's still there so that's obviously coming either from the right and supply module and or from the mean will last supply and it's just passing straight through so what I'm going to do now is pair it back from the lab bench power supply so we get rid of the mean world 1 and see if that goes away and well nope that's not coming from the mean well supply that's coming from the ridin module unbelievable look at that yep that switching noises absolutely horrible Wow I mean that that is really terrible that's that's under no-load so at 45 volts output that is a 20 millivolts per division I've changed my probe here we are at 50 millivolts per division let's drop it down to 5 volts bingo it's higher at 5 volts look at that that's 100 millivolts per division so that's peak to peak you know that's like a 100 200 300 400 or might like 500 millivolts peak to peak of course if you take the RMS of it it's not much but I didn't like that that is that's with no load that's terrible Miriah so this is with my rohde & schwarz lab supply and let me switch the mean well in and that's exactly the same with the mean well supply there okay that's off let's switch on a 1 at 1 amp constant current load yeah you can start to see the ripple there so that's off it'll be thinner and flat and on is that so if we could just get rid of the high-frequency crap this thing would be alright but that's all over the shop don't worry about that that extra stuff out there is just a triggering thing there we go that's 6 amps so I think that that's where they're getting their hundred milli volt spec font yeah that'd be two divisions yeah so that would be a hundred millivolts our peak to peak is what the spec sheet says but they don't tell you about the switching noise so they're just talking about the lower frequency ripple there which at four microseconds per division one two three and a half divisions there you can calculate that yourself what the switching frequency is so that's five volts at 6 amps hundred millivolts per division like seven hundred milli volts peak-to-peak not great is it I guess that's the price you pay for your fifty bucks at 300 watts in a tiny little module like this it's yeah and they've got to cut corners somewhere but G's can add our own an output filtering but that'll have to be another video well let's go back to the key site here five volts at six amps there we're looking at you know once again the RMS noise isn't very bad if you want to look at it that way now for 70 millivolts peak to peak alright I knew this defibrillator tester had come in handy it's got a big-ass 50 ohm resistor in here so let's a single shot capture are turning on 40 volts here and that'll give us a 30 watt load boom there we go nice and we'll switch that off and that's a clean switch off too and that is turning on into constant current mode you can see the CC down there and that's clean as a whistle as well and let's try that going from 45 volts into constant current mode yep there we go a little bit of undershoot there but that's no it's not doing anything strange not oscillating so that's quite nice and then we'll have it coming back out of constant current mode a little bit overshoot there is a teeny-weeny bit let me try that again little bit of overshoot there but nothing to write home to your mom about so let's play around with the user interface here you can I do shift lock by the way and that just locks absolutely everything so you can't do a thing that's fantastic so let's go into the menu shift menu and we're in like Flynn now you have to press these arrow keys to go between the main options at the bottom there's a firmware for those playing along at home and here's where we set up all of our programmable settings m0 is the one when you are pair up will go up will go enter and we can go V set like that and we can just go 5 volts so let's say we wanted 5 volts at half an amp for m0 then we press enter like that and that will store it and it took me ages to figure out how to get out of the menu by the way you've got a press that again there's you can't do shift menu or anything to get out of it and then we can simply recall those so let's go out and we can go that'll be our boot so let's boot that up and see if it goes to 5 volts at half an amp there it is there beautiful then we can go to m1 for example and that'll show us and there's an option not to have that pop up so anyway if we want to select that then 5 volts at now 6.1 amps there you go so in the main menu were set up here what we've got is that call ok that's actually as I just said - what call out like when you press the memory buttons it pops up with that menu pair on is whether or not you want the output to switch on when you actually pair it on well not usually you know you wouldn't have that just in case beeper is obvious logos obvious English there you go it for those plan long at home English and Chinese that's it and the interface we the options we have are USB Wi-Fi or TTL TTL doesn't work apparently USB it looks like it's going to give us a serial port from the u.s. be 115200 board and measure here is how fast you want the voltage reading on the display to read back so that's the sample rate basically and in this menu here we can choose which display we actually want our voltage and current display or a waveform display so let's give that a bell shall we get out of there and bingo we got a graph so let's switch it on there you go and it just shows you the voltage and it just basically graphs over time that's you know kind of neat but yeah I don't know new shoes and then if we boot up after selecting Wi-Fi it comes up with our Wi-Fi config so I'm not sure what the deal is there they've got both Android and iOS app it's called adipower I'm only a hundred and plus people have downloaded so we'll install that Wi-Fi is not connected connected slave address says it was connected it's not slave address can you have more than one probably if I press connector says and connect it but it doesn't like turn green or anything like that I don't see anything changing nope I ain't working well that Wi-Fi didn't work at all I couldn't find the device in the list of Wi-Fi products so I don't know what the deal is the manuals are not the best let's just say that anyway USB does work it shows up I just plugged it in Windows 10 and it showed up as a serial port unfortunately I've tried a terminal program I can't get any response from it so it could be a custom interface it doesn't say anything about supporting Skippy commands or anything like that so we'll have to download the program but this is the manual here it's good to know it has no virus if you're any software prompts please allow it bla bla bla so we'll install the software okay it's just a single XE 282 kilobytes that's what I want to see it's be serial install Jesus really old-school done that's that's the driver okay PC software it was just the driver unzipped files and double check to install the driver operate the software is not there let me go to this one it's a different address okay we've got a RAR file now okay looks like that's gonna do the business failed virus detected love it more information wow this is not a good look I got exactly the same our virus warning error under opera here and I'm not logged in there just yet it detected it no I am NOT going to bother I if that's like sorry I just look here it is here's the software this is what it's going to look like it's probably under work it doesn't support looks like it doesn't support standard Skippy commands although I guess you can debug this and see what it's actually sending and things like that because it is a serial port should be pretty easy to decode it and stuff like that you can have multiple units and things like that and this is where you can do firmware update so you've got to install this software which does not contain a virus to download your firmware and I don't know why you might need the driver because the did install is a serial port anyway I'm just not gonna bother no sorry someone else can do it now let's try out this battery charging functionality there's nothing in the menu that you can do for this it's like completely automatic so let me actually hook a battery up here and watch this symbol here it turns red and it's detected it there you go one point two seven volts so like I don't know where you set up the charging parameters for different types of batteries um I I don't get it so I can only presume that we have to manually do it like this so 1.5 volts for example half an amp whatever we've got our battery connect it's 1.27 let's press on its constant current charging at half an amp where she cut off voltage I guess I could set my over voltage protection could you its rudimentary but that's no different to a regular bench power supply like you can do exactly the same thing so I don't get it okay it might give us a total lie capacity but like geez I'm not gonna write home to my mom about it now there is a table of like different battery types in the manual and things like that but it doesn't really make sense of how it works and they're linked to an operational video of the battery charging mode there's no video there so I don't know so there you go that's the right and rd6 w6r lab at power supply and 453 US bucks delivered for the module it is actually very impressive value for money sure there's a few issues with it but geez you know the user interfaces is pretty good it's performance apart from other noise on it is pretty good and of course you can't complain about the flexibility and the specifications really apart from our to be nice if it did some boost converting as well but geez you know that's a tough ask for something like this so jewels they do have other modules if you're into combined a buck boost or Sepik converters you have a specific need for that like you might want to run it from a single lithium ion battery lithium polymer polly put the kettle on battery or whatever and you need to get like zero to thirty volts out then there's they have different modules for that but the previous one we looked at grant it was only twenty bucks this is no 50 bucks I'm another $23 or whatever for the case which is really quite remarkable it's quite a nice case and how it all bills together and how it supports you know many different times and types of both open frame clothes frame or other types you can even put a linear supply in there if you're really wondered into you know drill a few holes and put in a big title transformer and you know a bridge rectifier and all that sort of you know old school our business and very flexible in terms of being able to power this thing from many different sources so if you want to roll your own case and provide your own power solution then you know you really don't have to pay any more than your 53 US dollars delivered for this thing so it's absolutely remarkable value of course there's there is that issue with the noise we might do another video maybe looking into ways to reduce that perhaps but yeah this video is long enough already but yeah this is remarkable value but we did have issues I couldn't get the app working I couldn't get the PC software I didn't want to get the PC software working everything's a bit how are you doing in in that respect but the build quality is great and the performance is there so yeah I'm really like this I said the shame about my I mean well power supply inside this thing the fans just constant I might have to look into that yeah this is a really great banker bike so oh link it in down below even though this one does have a few issues geez the value for money you've got to give this thing a thumbs up it really is quite remarkable if you know of any better value than this in a similar like performance spec wise then you know please let us know but and if we can improve the noise that'd be fantastic and and it'd be nice if they added skippy support for example serial you know just a regular serial support but I'm sure as someone out there or just a decode the serial protocol and Bob's your uncle so anyway these things it's pretty impressive so I'll leave a link down below to ride and Riaan text the Olly official Aliexpress our webstore I recommend you buy it directly from there our resellers around and things like that but I don't know what the deal is so yeah anyway if you liked the video please give it a big thumbs and as always you can discuss it down below catch you next time [Music]
Info
Channel: EEVblog
Views: 486,256
Rating: undefined out of 5
Keywords: eevblog, video, rd6006 review, rd6006 power supply, rd6006w, lab power supply, bench power supply, riden, riden rd6006, wifi power supply, switching noise, lab power supply design, power supply review
Id: 0qjLx_HsKUQ
Channel Id: undefined
Length: 38min 3sec (2283 seconds)
Published: Wed Nov 27 2019
Related Videos
Note
Please note that this website is currently a work in progress! Lots of interesting data and statistics to come.