Delta VFD Factory Reset, Basic Set Up, Digital Keypad Start Up, Parameter Reset VFD-E. Potentiometer

hi what's up so i've just recently purchased this vfd it's the delta vfd um it's really good quality um i bought it but it arrived but it was missing this um keypad this digital keypad um so i had to buy this separately so i bought this it just pops off like that okay so i bought it um and also before i continue if anyone knows this about what this is supposed to be this was all on off if you look here see them three buttons there um they were all on off i've left it so the first one there's uh there's ready run and fault ready run and fall so i've put the ready on and run on i've left the fault one on um off so if anyone knows more about that but it seems to be working now anyway but they were all on off so if you've got it on off i think it might be wise to put it on except for the fault one which i left off but anyway okay so that's the vfd so you just connect it straight back inside i think you put it this way connecting like that and just push it that's it job done okay so bought it so i can um control so it's a single phase vfd i bought it to control the speed control of this three-phase motor which i've connected all up you can see it okay so as soon as i receive this digital keypad let me just switch it on right now always use a power breaker it's always best to um the thing is it wasn't working so and i used i did everything i can to make it work you know this thing here was just not working it's working now but it wasn't working before so i did everything to make it work and it just wasn't working and every time i kept putting the code in the code which is on here and by the way you need to make sure you keep this safe the delta parameter manual this has got everything in it that you need need to know so i followed the code and everything um i did it um the codes were on like unity control which is um zero to zero zero which is there for the controlling of the i think it's the fourth one which is a digital keypad production but anyway um it was set on zero which is the up and down which is there but none of it none of it was working so i spent an hour kept doing it over and over and over again eventually i had to reset it now i didn't know how to reset i tried looking everywhere but i couldn't see it eventually i found it here so this is a video just to show you how to reset it anyway it says parameter reset all parameters are reset to factory settings if you follow this parameter um i tried this one which is the 50 hertz but it doesn't work so i tried it the 60 home when it worked on this so i made sure i wrote it down for the future so there's no messing around so zero zero zero two and ten that's to reset this one i'll show you right now anyway um so um before i also show you how to reset it if anyone knows why this fan is constantly staying on um just let me know because this fan just seems to be staying on all the time i don't know if there's a fault with it or something or what but if you know anything just let me know so here we go so i'm going to reset it right now okay what you do you press mode remember it's um zero zero zero the param parameter reset is zero zero the code zero two and 10 because it's the 60 hertz so let's go to mode quantum mode until you see frd then press enter okay you want 0 0 first you go to zero zero then enter and you want zero two go up twice to zero two enter and then you got this now i was going on to nine which is the 50 hertz wasn't working so then you go into 10 then enter it does that as well it does error quite a lot so if that ever happens you have to reset the thing you have to restart it so let me try again okay so enter on zero two and i'll go to ten again let me try it on nine see what happens okay it's end on nine r okay now it's on fifty hertz but i want it on 60 okay so i want to try that again mode mode okay i thought entel zero zero enter zero two enter i want ten enter okay now it's set on turn d comes up as soon as it said d that's it it's reset okay now let's see what happens let's see i've already connected the motor okay so let's see what happens it's not working at all right now because you've got to set this to work you've got to do the parameter of this to make it work okay okay another one is working okay now in order to turn this to make this work to make the let me see to make the motor turn it's all connected it's just not working okay this is what i need to do okay the first thing to do is on the let's just go to this one you want okay here it is i showed you earlier okay digital keypad up down keep as no i don't want that one because that i think controls the up and down there so i wanted this to i want to use this so what you do is go to digital you go zero two then zero zero then you go four for the digital keypad potentiometer i think the potentiometer is this thing here but anyway let's just see what happens okay so stay on f go to mode [Applause] oh sorry go back to f press enter so you want zero to [Applause] enter then zero zero which is already on then enter then you want one well right now it's set on one which is not going to work because it's the digital keypad um okay so you want four for the digital keypad potentio whatever you have is the potentiometer so let's try that four then enter end okay so let's see what happens now let's get out of there let's go to f okay now it's working but it's working perfectly but the motor ain't turning yet okay so in order to make the motor work i think you need to press run run but runs not working so now i need to figure out why running working so what i do then i go on to this further you stay on the same page there's got to be something here which shows you now let me just see okay i might have to focus on this stop method so you go to zero two zero two and then whichever one so i think it might be set on the wrong one so let's just see oh actually wait a minute digital keypad source of information okay let's try this one zero two zero one uh digital keypad it might be on an external one because i want it for internal so let's just try this zero two zero one so anyway go back to left okay uh enter 0 2 then you want enter then 0 1 enter 0 to 01 right now it's on external terminals keep keypad stop press enable you want digital keypad which is on zero so let's go into zero it was on it was on one that's factory reset to go to zero and then enter end now let's see if this soccer works um so mode okay now okay this works but let's see if you run if it works if you press run okay now it's on so in order to make it work you press now that run is working so let's see if it turns the motor now if i turn this yes it's working now okay so that's our 14.5 it's working perfectly so this video is just to show you the basics of how to set it up after you re-reset it to factory settings so yeah there it is um it's just to show you that yeah that's how you can start it off if you've got any problems with it how to reset it and just do the basics to kick it off the good thing about this book is i'm really surprised it's really fun this is actually really fun if you've got a lot of time it tells you everything and you if you've got a lot of time to go through it you can just do it and it's so easy it seems complicated but it's so easy make sure you hold on to the manual because this manual has got all the answers and just take your time and relax and do it and remember if you've got any issues where you do the code and it doesn't work it means it needs resetting once you've reset it it's back to your factory settings you won't need to do a couple of bits and bobs like i just showed you just to kick it off um and that's it so yeah i hope it goes all right for you but remember it's it is fun it's actually you enjoy doing it if you've got the time so i thought it was a bit of a new sense of being but i'm really enjoying it but like i said you need a lot of time and you need patience and you just read through it you just read to it don't ever panic or anything so it's all there and it will work it's a really good quality unit it's nice and heavy in comparison to others [Music] so yeah i mean it was worth buying anyway this this make particularly was worth buying more than any other mate so yeah there it is um and also like i said if anyone knows why the fan is continuously on i haven't got a clue ever since i bought and connected it the fan is just been on all the time for some reason so um if anyone knows why please let me know in the comments so i'll just do this again show you look at that beautiful you can set it to anything any speed you want that's the good thing about this video if you can do anything you want so right now this is a single face vdf it's running a three-phase motor so yeah it's great to have one okay thank you very much for watching please like and subscribe thanks

Channel: SJP1

Views: 40,718

Keywords: VFD, VFD-E, DELTA, delta, vfd, vfd-e, delta vfd, Delta VFD Factory Reset, Basic Set Up, Digital Keypad Start Up, Potentiometer, parameter, delta parameter, vfd parameter, parameter setting, vfd settings, vfd setting, delta setting, speed control, motor, electric, electrics, electronics, basic start up, start up, vfd start up, vfd set up, delta vfd set up, delta manual, parameters, parameters set up, electric motor, vibrating tumbler, tumbler, diy, news, war, rotation, rotate, motor set up

Id: CVaGyu7AVgQ

Length: 12min 24sec (744 seconds)

Published: Fri Nov 20 2020