Best Ceramic Coating? $8 vs $120? Let’s Find Out!

Video Statistics and Information

Video
Captions Word Cloud
Reddit Comments
Captions
an unprotected car paint finish is just not going to last nearly as long as one is properly protected so the question is is that $8 ceramic coating just as good is it one to cost $150 well let's find out in the first test we'll see how well the ceramic Coatings protect car paint we'll also see how well they protect plastic before I apply the ceramic Coatings I'll wash the front hood which will serve as a test area of the vehicle pour 2 to 3 ounces of strip wash into the bucket spray hose directly into the wash pad to dispense soap and create SIDS fill bucket 2/3 full now that I've washed the vehicle with strip wash I'll need to remove all the contaminants from the paint a clay bar is designed to remove environmental contaminants which can deteriorate a paint's finish it does a great job removing brake dust that becomes lodged inside the clear coat the clay bar that I purchased comes with this lubricant which allows a clay bar to slide freely sometimes a clay bar isn't able to remove all the brake dust so I'll go ahead and apply an iron remover which will quickly break down any remaining iron just to be sure the test area is completely clean I'll go ahead and wash the vehicle one more time with the strip wash at a price of only $8 is this shine armor brand it claims to offer your vehicle a waterless wash coat and shine it even includes two microfiber towels the shine armor is made in USA let's first measure the slickness of the paint without any waxes or Coatings the digital angle gauge shows that the front hood is level I'll use a brand new sponge with 5 lbs of weight on top of the sponge and the unprotected paint just isn't very slick as it's taking right at 4.5 lbs of force for the sponge to slide since we're testing eight different ceramic Coatings I'll go ahead and create eight different test areas on the flattest areas of the front hood spray onto a clean damp microfiber cloth and onto the surface you are cleaning gently wipe the surface with the first pre-wetted folded microfiber cloth quickly switch to a clean folded dry microfiber cloth and buff off the remaining Haze before it dries repeat this process until the entire vehicle is clean streak free and Ultra glossy it's also safe to use on glass paint and metal and plastic headlight covers are made of polycarbonate and it takes quite a bit more Force to slide the sponge across a polycarbonate panel at 12.7 lb let's apply each ceramic coating that we'll be testing to a brand new po carbonate sheet for additional testing and it's all about ease of application the shine armor is very easy to work with and Buffs to a nice shine with very minimal effort at a price of $15 is this hybrid Solutions on the previous review on ceramic Coatings the hybrid Solutions did an amazing job so let's see if it's still performs well it claims to offer extreme water repellency we're going to test that they claim it's long lasting and it can last over 6 months the hybrid Solutions is made in USA for best results do not over apply the active formula use two sprays per panel spread it and wipe with a clean folded microfiber cloth use a separate microfiber cloth to remove you can also use this product on exterior glass Plastics and more just like the shine armor the hybrid Solutions is very easy to apply and Buffs to a shiny finish with minimal effort at a price of $17 is this SRA coat brand it claims to offer unsurpassed slickness we're going to test that it also comes with a microfiber towel it claims to be extremely hydrophobic and the S coat is made in USA Park the vehicle in the shade or out of the sun gently Shake bottle for approximately 10 seconds evenly spray a light coat directly onto the surface using one side of the towel wipe the coating evenly across the surface immediately flip the towel to a clean dry side and buff the coating to an incredible shine inspect each section after buffing to ensure no Haze remains if Haze is present buff the haze away to a high gloss shine it'll be fully cured in about 2 hours during this time you'll notice the gloss level and slickness increases dramatically do not exposed to moisture during the 2hour Cure and the aak coat is also very easy to apply just like the shine armor and the hybrid Solutions at a price of $25 is this Chemical Guys brand instructions for use include shaking the container well spray onto the surface working one section at a time use a clean microfiber towel to gently wipe the area clean for best results do not apply in direct sunlight the manufacturer claims extreme hyperactive water beating they claim it offers protection against UV rays extreme weather and contamination The Chemical Guys is made in USA and The Chemical Guys is very easy to apply but it did take just a little bit more effort to buff to a shine compared to the cak co at a price of $38 is this Nano Bond brand in addition to the bottle of ceramic coating it also includes a sponge microfiber towel and micro SED applicator and gloves the Nano bond is made in China the first step is to wrap the cloth over the coating sponge Put liquid on the cloth spread the liquid on the car and wait for 1 to 2 minutes for the liquid to dry use the towel to wipe and polish it's supposed to leave a glass-like finish they claim it offers outstanding water beating that makes the water almost jump off the surface it's supposed to offer protection for up to 36 months the Nano bond is made in China instead of a spray and wipe like the other brands the Nano bond is a wipe and weight system that takes about four to five times as much time to apply at a price of $60 is this topco f11 Pro the kit includes 16o f11 Pro spray bottle 2 oz travel bottle and two microfiber towels they claim that their product is the most advanced water-based ceramic coating the f11 is made in USA Spray f11 Pro directly on the surface coating one area at a time immediately hand buff f11 Pro in with a dry and clean top coat microfiber towel use a second Dy microfiber cloth for final buff to ensure the entire surface area is polished and potential areas of overspray are removed repeat this process until all areas are coated inside and out let cure for 24 hours it's supposed to last up to 12 months and the f11 top coat sprays on quickly and wipes away easily at a price of $90 is this Advanced graphine coating the claim it last up to 10 years includes two microfiber towels it also comes with a couple pairs of gloves wrap the cloth around the sponge and apply four drops of graphine coating apply in straight lines first apply horizontally and then vertically to an area about half the size of the hood make sure to apply one to two drops whenever the sponge feels dry or when you don't see the product being applied to the surface immediately after buff the surface gently in circular motions with the microfiber cloth they recommend folding the cloth and using one side for the first stage of the initial buffing and then the other side of the cloth for the more thorough buffing the advanced graphine is made in USA there's no way time before wiping off the advanced graphine making making it just about as quick to apply as a sprayon products at a price of $150 the most expensive coating we'll be testing is made by Adams and cost $150 the kit includes Surface Prep graphine boost and the coating it also comes with a couple of applicators two micro suede ceramic towels it comes with a couple of soft plush towels they claim it offers 9 years of protection apply Surface Prep to remove polish residue wipe away using a single soft microfiber towel apply numerous drops of graphine ceramic coating to the suede applicator work a 3ftx 3 foot area at a time use a cross-hatch pattern to ensure full coverage once the coating is applied to the surface it will begin to cure and have the appearance of a rainbow or oil slick as the rainbow color starts to dissipate on the paint it's time to begin wiping away the surface oils using the micro suede coating towel first lightly wipe and level the coating surface oils if excess oils persist use a plush microfiber towel to fully wipe away the ceramic residue allow the coating to cure for a full 24 hours it offers 10h hardness it's supposed to be extremely hydrophobic slick and versatile they claim to offer 110% satisfaction the atom ceramic coating is made in USA and the atom seems to take just as much time to apply as a nano Bond coating and cannot be wiped away immediately after application assessing ease of application is highly subjective however the spray on products are definitely easier and faster to apply compared to the products that require use of a sponge or applicator all of the ceramic Coatings have had well over 24 hours to cure in a temperature controlled environment that's very close to 77° f plus once again measure the slickness of the paint and the sponge is sliding on the shine armor with 2.4 lbs of force which is quite a bit better than the bare paint at 4.5 lbs of force for the sponge to slide and the hybrid Solutions is very slick at only 1.5 lb which is almost a pound better than the shine armor and the cak co performed well and moves into second place at 2 lb or half a pound behind the hybrid Solutions and a chemical gu is only 1/10 of a pound behind the hybrid Solutions at 1.6 lb which is good enough to move into second place and the Nano bond isn't nearly as slick as the spray on products at 3.3 lb to move the sponge and the f11 performed well at 2 lb the same as the cerakote just like the nanobond the advanced graphine isn't quite as slick as some of the spray-on Coatings at 2.4 lb and the adds performed very well at only 1.7 lb so the hybrid Solutions finished in first place at 1.5 lb but the chemical guides at atoms weren't too far behind at 1.6 and 1.7 lbs respectively the tape is definitely going to get in the way of the testing I'll go ahead and outline the test area using a permanent marker and I'll remove the tape now that the tape is off I'll go ahead and use a larger marker just to make sure we can see the test area boundaries throughout the testing before we kick off testing on the ceramic coatings on the vehicle let's kick off testing on the polycarbonate sheets ceramic Coatings are a great option for protecting headlights from becoming oxidized so let's place the polycarbonate sheets inside of the dishwasher to see how they hold up to relatively warm water I won't use any detergents or additives and we'll check back on this later in the video and the shine armor is performing well and the water is mostly beating and not forming a sheet and hybrid Solutions is definitely performing better than the shine armor and that's some pretty impressive water beating let's dial up the intensity and volume of water for a side by side shine armor is on the left and hybrid Solutions is on the right and the hybrid Solutions is definitely performing quite a bit better and a cerakote is performing better than the shine armor and about the same as the hybrid Solutions and the hybrid Solutions and zerak Cote are both performing very well and this one is too close to call and The Chemical Guys is looking really good but the hybrid Solutions in sakote might be just a little better and a side by side with more water volume and the cak Coe is definitely performing better than the chemical guys and the Nano bond is performing well with the water beating and no sheets of water forming there appears to be a vertical water flow pattern which indicates an inconsistent finish with the Nano Bond coating I did follow the manufacturer's instructions and waited 1.5 minutes before wiping and polishing the coating but that may have been a little too long and the f11 is performing well with most of the water beating but there's more sheading compared to most of the other brands a side by side with the Nano Bond and f11 and the Nano bond is performing quite a bit better and the advanced graphine is definitely performing better than the f11 but not quite as well as the hybrid Solutions in cak Co and there's a sheet of water covering the f11 and the advanced graphine but the sheet of water cleared up faster on the advanced graphine so Advanced graphine for the wind over the f11 and there's nothing but water beating with the atoms and it's doing by far the best yet very impressive increasing water volume and intensity and the atoms still refuses to let the water form a sheet very impressive assessing performance is highly subjective but the atom came out on top Nano Bond performed well finishing in second place and hybrid Solutions in cerakote tied for third strip wash is designed to wash away heavy dirt and even car wax I'll make just two passes across each ceramic coating with a light spray the shine armor is a solid sheet of water so the strip wash pretty much destroyed the shine armor even after the strip wash the hybrid Solutions continues to demonstrate excellent hydrophobic qualities and the cak co is also performing very well after exposure to the strip wash comparing hydrid solutions to sakote they both look about the and are performing very well water is also beating very nicely with the Chemical Guys comparing the sakote to The Chemical Guys sakote is doing a little bit better with the water forming a tighter bead and water is beginning to form a sheet on the chemical guys and the Nano bond is still performing very well with the water forming beads across the entire test area unfortunately the f11 is forming mostly a sheet across the test area and the Nano bond is definitely performing quite a bit better than the f11 after exposure to the strip wash and the advanced graphine is still performing well after the strip wash but the water is beginning to form a sheet in some areas however the advanced graphine is definitely performing better than the f11 and the hydrophobic quality of the atoms after the stripw wash exposure is by far the best yet between the Advanced graphine and the atoms is not even close definitely a win for the atoms after exposure to strip wash let's see how the Coatings hold up after exposure to iron remover it's a pretty powerful product that'll definitely cause some damage to some of the products and the iron remover really disarmed the shine Armor's protection and it's almost used up the hybrid Solutions is still performing well but the IR remover definitely had an impact and the serak code is also performing well after the iron remover however the hybrid solution seems to be holding up just a little bit better and chemical gu seems to be almost as good as a cak CO and the Nano bond is holding up the best so far with water forming mostly beads and the f11 is still offering a little protection but the water is mostly forming a sheet and the advanced graphine is still trailing the harbage solution serot and Chemical Guys and the Adams is still performing just as good as new with nothing but water bees very impressive bug andar remover is a another powerful product that'll really put these Coatings to the test I'll give the bug andar remover 3 minutes to go to work after a quick rinse with water I'll wash off the front hood with strip wash once again and the shine armor is completely used up and there doesn't seem to be any protection left and the bug andar remover definitely did some damage to the hybrid Solutions but water is still beating the bug Andre mover seems to have caused more damage to the cerak co with a heavy water spray it took 15 seconds for the sheet of water to dissipate with the hybrid Solutions the chemical gu also experienced a lot of damage a heavy spray and a sheet of water quickly formed the cerakote and chemical guys needed a full minute for the water to dissipate and the Nano bond is performing even better than the hybrid Solutions and the f11 top coat appears to be completely used up but the Nano bond is clearing up in only 4 seconds the best yet with a light water spray water is quickly forming a sheet over top of the advanced graphine and the atom still looks as good as new with only water beads even with the heavy water spray water is still beating up on the atoms and it took close to 45 seconds for the water sheet to dissipate over the advanced graph so the atoms remains on top without water forming a sheet over the atoms even with a heavy water spray Nano Bond finished in second place at 4 seconds and hybrid Solutions 15 seconds let's go Ahad and check in on the polycarbonate test pieces after 2 hours of warm water spray all the Coatings are still holding up just fine Dre sunlight exposure creates a lot of heat so let's simulate those conditions by running 2 and 1/2 hours using hot water spray after just a few minutes the water temperature is around 120° inside the dishwasher Wheel and Tire cleaner is in pretty powerful Stu I once again wash the test area with strip wash just to make sure that all the wheel and tire cleaner has been removed even with the light water spray water is forming a sheet over the hybrid Solutions and is pretty much used up and this a code is also used up with a sheet of water covering the entire test area and the chemicals have definitely taken their toll on the chemical guys and the Nano bond is performing the best so far with the water unable to form a sheet over the entire test area and the advanced graphine is pretty much used up and the YZ is performing by far the best so far with mostly water beating I put other review on degreasers a while back and we'll see if any of these products can survive the best degreaser that I tested I washed the test area once again with strip wash just to make sure that all the Degreaser has been removed the first four products are spray and wipe Coatings and they all appear to be completely used up the f11 and advanced graphine are also pretty much used up so it comes down to the Nano Bond and the atoms and the Nano Bond experienced quite a bit of damage from the Degreaser but it's still providing protection it took 15 seconds for the sheet of water to clear and the atams is still doing a great job with only a small water sheet forming and then clearing in about a second very impressive the Nano bond is on the left and the atoms is on the right and it's definitely a win for the atoms I dried off the front hood a couple of hours ago and it's completely dry it took 2.1 lb to move the sponge on the fresh shine armor coating and now it's at 3.7 the hybrid Solutions perform just a little bit better at 3.5 and a serot and chemical guys are both performing about the same as a shine armor at 3.8 and the Nano bond is performing the best so far at 2.4 lb and the f11 is at 3 2 lb in the advanced graphine 3.1 and the Adams takes the lead from the Nano Bond at 2.1 lb and 4 and 1/2 hours of warm and hot water spray took us toll on the shine armor about 13 seconds for the sheet of water to completely dissipate a much smaller sheet of water formed on the hybrid Solutions and cleared in only 4 seconds the serak co performed very close to the same as the hybrid Solutions and the water dissipated in close to 5 seconds and the sheet of water on top of the Chemical Guys cleared up in about 7 seconds and a small sheet of water formed on the Nano bond in 3 seconds seconds is the fastest time yet a larger sheet of water formed on the f11 and it took 7 seconds for the water to clear the test piece and the advanced graphine performed about the same as the f11 at around 7 seconds after 4 and 1/2 hours of warm and hot water spray the water is not able to form a sheet on the atoms very impressive so the atoms came out on top for warm and hot water exposure nond finished in second at 3 seconds and hybrid solution 4 seconds so which ceramic coating is the best and the atams totally dominated The Showdown finishing in first place however Adam is pretty expensive at a price of $150 and it does take more time and effort to apply compared to the sprayon products on the other hand Nano bond is a lot more affordable and finish in second place if it's all about finding a product that performs extremely well and is very affordable I really like the hybrid Solutions it did a great job finishing in third place and at $15 it's hard to beat the durability of these ceramic Coatings is pretty impressive all the videos in this channel including this one our viewers suggested so if you have a video idea I hope you'll take time to leave a comment thanks so much for watching please take care and look forward to next time
Info
Channel: Project Farm
Views: 863,756
Rating: undefined out of 5
Keywords: Ceramic coating review, best ceramic coating comparison, adam’s ceramic coating review, nano bond ceramic coating review, hybrid solutions ceramic coating review, cerakote ceramic coating review, chemical guys ceramic coating review, topcoat F11 pro ceramic coating review, shine armor ceramic coating review, 9h ceramic coating review, 10h ceramic coating review, graphene car sealant review
Id: O2lrXVV9kWU
Channel Id: undefined
Length: 17min 1sec (1021 seconds)
Published: Sun May 12 2024
Related Videos
Note
Please note that this website is currently a work in progress! Lots of interesting data and statistics to come.