ANOTHER AMAZON Returns MYSTERY Box from eBay? Can I FIX it?

[Music] hello there my name is Vince from mymave Vince and here we have another Amazon return box from eBay yes 50 items for 50 pounds I got this one for 45 pounds because eBay was offering a 10 discount and I took them up on it and that's the reason it's 45 pound I already did one of these a few weeks ago and it was really well received so here we have another one now the seller did actually watch my video on the first one and then I said well I've ordered another one for you because I actually ordered another one before the first video went live because I really enjoyed doing it even if the video wasn't going to do well I thought it'd be fun for me to do another one and uh yeah I don't know whether this one has been tailored a little bit because it's my mate Vince not too sure but I was very happy with the first one and that was just completely random I don't know what's in here that's part of the fun oh look at this right straight away what we got here discover our portable smart speaker excellent a little light mini that might actually do for filming batteries can never get enough batteries fantastic you can check them later oh a battery charger for I don't know for what make obviously it's a third-party one yeah you know like Makita or something like that another speaker next space dash cam power a Xbox controller well there certainly seems to be some big ticket items in this box here considering that it's a pound an item you can see that if you were a reseller there would be profit to be made now I do think this has been tailored for me the Box seems a lot heavier than the first one I got so I think the set has done me a favor because he would have sold quite a lot of boxes from my first video because it done well it got I think 80 000 views so far so uh yeah this wouldn't be indicative of an item that you would buy from eBay but my first one definitely was but hopefully with this one here we have some bigger items that might make for more interesting fixes so I'm going to sort through them now see what's working what's not working and then we can start fixing so first up we have this and this is a little ultrasound it says here pocket fetal doppler so if you're pregnant you would put some ultrasound gel or it says on the bottom here that you could use olive oil or baby oil and then you'd rub this across your belly and hopefully you would hear the heartbeat but look there's batteries in it and when I turn it on it's not doing anything and I've measured these batteries and they are measuring okay they're brand new so what is the problem gonna be I think maybe it's something to do with a power switch or maybe there's a context between here and the circuit board but if you look here we've got 1.6 volts in them 1.62 and one point six two so they're brand new batteries so let's try to get into this let's see a little screw here so start by undoing that and then what we've got here a little RJ 10 I think that might be well RJ 11 bit small I think that might be an rj10 uh Let's uh undo that screw and I presume it just prizes apart already I can tell that I'm really going to enjoy this slot here because there's so much to get through and some items I would have never thought to buy or look at there we go so it is clipped there we go can you see already I'm not going to say anything I'm just going to zoom in this is what I love about honest faults move my blue mat around to help you do you see anything on here that doesn't look right there you go boom there's no power getting to there because this wasn't plugged in properly either from manufacturer or maybe in shipping it's got knocked out so if we put that in there there you go I mean that goes in with a nice click I don't think that was put in properly to begin with because look that doesn't seem to want to come out easily you really have to yank that that was never put in from uh from from new let's see now if we have life in it come on there we go resolved what an easy fix well do you know what I don't mind just here because I've got many things to go through I was going to say I'm going to add some glue to it but it really is no need you see how hard that was to unplug so uh let's just put it back together here [Music] and I'll flash up on screen Hammer actually no I want to know myself how much it costs all right looking on Amazon I thought there would be loads of them for sale but now it's only this one for 48 pound and that one's unavailable and after that it's like using gels so when you turn it on here you've got the volume so you've got like a volume up here I've just had a little guy myself and personally I can't actually feel it so uh presume you do have to have some gel to make it conduct yeah I thought I'd be able to hear my heartbeat I can't anyway I'm going to assume it's working because the thing is we've seen a visible full and it also looks like there's other settings as well so if I was to go uh that's volume one second if I press this one here one two and something like that so I need to read up about it but I'm not in the market for one at the moment anyway but still and I said it was fixed let's move on to the next thing right now let's get the next item oh oh what a nice subtle way to introduce the sponsor of today's video so if you like fixing things like me maybe you might also like making things as well and if you do if you want to bring your project to life in a nice professional way then look into PCB way PCB we have over a decade experience in the PCB industry they have state-of-the-art manufacturing facilities and they use the latest technology to produce high quality pcbs that meet your specification at PCB way they have a range of services including PCB prototyping PCB assembly flexible pcbs high density pcbs CNC Machining and 3D printing now if your project is going to be using components that produce a lot of heat you could think about using aluminum pcbs because it will allow for better heat dissipation it will transfer heat away from those components and guess what PCB way do aluminum pcbs as well so a massive thanks to PCB way for sponsoring the my mate Vince Channel now let's move on to the next item a JBL waterproof speaker when I plug it in it's not drawing anything the light is coming up there's a little uh light that flashes I think here but it's not actually drawing anything from the meter so you might remember this from the first Amazon box that I did still working fine and if you have a look I'm gonna plug it in we will get a little light that flashes here not flashes but comes on but look it's not drawn anything yeah so that's not right it should be drawing something and we can't turn it on whether it's plugged in or not so let's tear it down that was also the same thought with this one here it wasn't drawn anything and it wasn't connected to the battery properly so let's see what's happening here now it's not the easiest thing to get into because it's held in with a lot of Clips it's also got screws and also there's some sticky pads on it as well but it is waterproof so it's going to be a little bit harder to get into start off by just prizing off the ends on each end and also on the back there's a big rubber pad that's stuck down so you can peel that back and once you do that it uncovers screws once you wonder what the screws I think there was four or five on the back and then a couple on each end then what happens is the whole kind of fabric cover comes off it splits into uh it only splits down one side but you can hinge it off then and then bit by bit there's other screws so you want to do on the inside and then it will give you access to the board and the battery now what's happening why are you not charging is going on so it's all glued in so the battery is there let's plug it in and see if we have any voltage across here because I can see it grounds and then maybe I can zoom in and see what uh what other test points there are V batteries let's go between ground and the battery so you know what let me just see if we plug it in the other way just in case no because it's USBC right let's have a little look here so there's no voltage getting this let's unplug that right so we've got nothing there let me just go on the actual prongs let's see if that changes when I plug it in plug it in now let's change a tiny bit to be fair but it's just incredibly low the dragon a battery has just failed because it is giving me something I think we need to unplug the battery and see what we have it should be 3.7 that's going to be awkward because it's had a load of stuff put on it which looks a little bit like the Loctite there we go annoyingly that has actually broken that a bit you see I've got a crack there now I think it'd be okay though right let's see what we got it was the outer two wasn't it I can't even see the color wires there you go black and red so let's go on the outer too no so there's nothing in this battery whatsoever it's called great power as well anything but great power unless of course there is a short on the board and it's causing no voltage let's have a look you know it's drained it completely Forum shorts hmm maybe maybe that's the problem maybe there's something on here which is gone tell you what let's see if we can get anything in the battery to begin with right so I've got this here which is a tp4056 there you go on my little battery charger here let me zoom out a bit it's gone to Red well let me leave it on there for a little while and uh would be nice is if I could get my probes on here I could actually see it going up on my meter here you go yeah let's climbing nicely all right let's just take that off and see if we've got anything in the battery now because I just need that initial little jump start 3.5 yeah okay let's plug it in just to see if that was enough to let this take over the charging let's see what it's going to do now still not drawing anything hmm okay I'll tell you what we'll do I think there's something on the board I don't believe the battery is 40. I think there's something on the board that's causing a problem which is fine but let's just first of all get a little bit of charge into this so while I'm getting some charge into this battery let's take out the board and see if we can see anything obvious because it looks like we have a short coming from somewhere we're free we are free now a little Mark on that ship there let's zoom in there we go that's 40. isn't it and zoom right in on that right luckily I can get a nice good reading off that still so it's ev4c I think that's a 2pf2 so I'm going to write that down let's scrape it a bit and see if that's where it's blown I would say yes I could still go in now yeah it's still down yeah I don't think that's just a little imperfection I think that's where it's gone oh that's a shame let me pop the chip off the board well I'll tell you what let's just see if we've got shorts around it on these caps because I presume these caps here are probably treating it let's see if these caps are shorted no no yes it's going to own reading on that if I just do my leads to begin with on their own so my leads right now are showing a 10 ohm shot and these are so annoying 10 ohms so now what are these 12.9 so basically this is where that four ohm short is coming from that we've seen on the other side I'm sure of it so let's just get out of curiosity uh get the hot air station on let's pop this one off let's see if that gets rid of the shorts if it has then I think we can safely say that that is the problem don't think I'm going to be able to get one of them but I will I will look it up let's not wanting to release itself from the board problem is I can't sort of do any sideways pressure because the board's moving all over the place let's see if anything else is loose yeah I can't get it off I thought I'm gonna have to clamp the board down there we go oh yeah it's got a little have a look underneath and that's why it's harder to take off I wonder if that's the ground well so that's what was hard to take off because listen yeah so when I go to the ground like the USB port here and here you can hear it so the ground was sucking all away and you can see it it's nice that the ground goes all the way up here yeah so that was probably uh you know helping to cool it all right let's see if the short on these have gone yes they have all right let's get an ohms reading so what was it before three ohms or something all right so that side is three ohms and this side it's now completely open yeah there we go I think we've proved there we've proved what the thought is now I wonder if it's obviously it's not going to work because I presume that's to do with charging it up I wonder though if we were to put the battery in would it come to life but maybe not charge I think we should try that all right let's see if it will turn on yes look listen did you hear that there you go out of curiosity let's see what will happen if we do try and charge it so it's not drawn anything and also there's no light on here either yeah so obviously that is the charged chip right so again our curiosity let's see if it will connect to my phone so this is the Bluetooth one here and we'll go to buy it fix it highly recommend you do check out his videos it really really knows this stuff yeah I watched all of his videos and I really like them now let's go to here well where's the volume on this thing it's up the top isn't it from eBay I'm successfully repaired it can be called that's the loudest actually uh seen that video and the Very kindly asked right okay so I need to look into that chip okay I don't think I'm gonna be able to get this chip if I type in ev4c ic or chips not bringing anything up if I type in ev4c and then the rest of it it's still not bringing anything up whether I type in chip or IC is still the same thing yeah I mean and let's see that too let me try three that two was where the burn was but you would think it would that you think there'd be enough digits there to bring it up now I'm sure it was a two so I don't think I'm gonna know what one of these chips are and this device isn't going to be popular enough for people to be kind of selling those aspares for it I was a real shame about that one I'm just going to keep the chip in here how long with this bit of paper you never know if the viewers can work out what it is then I can they're a revisit video on that feels so feels nice it feels a real nice little quality product all right let's move on to this weird sprocket thing okay so this is the HP sprocket the tiny little printer with sticky photos in it but it doesn't seem to be drawing anything or a tiny tiny amount and it's been plugged into the corner charging for quite a few hours and if you look that's all it's doing and it just has that flashing red light but it doesn't seem to want to go any further than that and as far as I can see that's that's too little off a charge yeah doesn't seem right especially when it's been plugged in for hours now so let's see if we can take it apart and see if we can work out what's going on with it now how do you come apart see there's an on and off button here but it's not doing anything when I press it but again I don't think it's a button problem because it would still charge up if it didn't turn on I'd say it's a button problem wow it's actually coming apart very easy do I spy oh no I thought it was going to be one of those uh 18650 batteries right okay well that was a lot easier than I thought this is nice and look at the gear and everything so is it like a little printer with a little rubber roller wheel okay I won't mess with that too much so now when we plug it in why these are not charging this battery what we got here red and black should we do the same as before plug it in here and see uh what voltage we're getting it's going to be out of two nothing now let's unplug it see what we're getting around about the same there's not much of a difference there is there just wiggling let's see if it makes any difference to the amp drawer no all right let's unplug that see if we can unplug this battery [Music] all right it's okay always says charging limited voltage 8.4 volts oh I didn't I didn't dream it'd be that high okay so it's uh yeah 8.4 volts let's see what we have in it we don't appear to have anything in this one either so it looks like the battery is completely dead now has something on the board made it completely dead or has the battery failed has it just been uncharged for a long time so what I'm going to do is get my bench power supply on this and I'm going to set it to around about eight volts but only 200 milliamps and let's see if it starts charging and see if we can get some charge into the battery and then maybe the HP sprocket will then take over and start charging once the battery's risen to a safe amount where it's happy to charge now obviously if a battery is flat you shouldn't be charging it up like this because it could be dangerous I'm just doing this with a bench power supply on low milliamps so I feel safe doing it I'm also going to monitor the temperature of the battery by feeding it every few minutes to see if it's getting warm okay I'm jumping in the next day now I was actually editing up the video and this was getting the better off me I didn't have a conclusive answer so I visited it again now and I've got more info hence the reason I'm re-filming this bit here so basically yesterday what I did I put my bench power supply straight into the red and black wires here and sure enough this did take a charge I've got it up to something like seven point something volts basically this is two 3.7 lithium cells together in series so we have 7.4 volts or 8.4 volts Max charging and uh when I got charged into this and put it into the HP sprocket connected to my phone sure enough it worked and I printed out a lovely picture of the dog that visited me and I was really impressed about how good the actual quality was of that picture you know like it really does look just like the picture on my phone because this line and stuff was on my phone when I took it because it was a sunny day so uh it worked fine while I had charging the battery but bit by bit it kept dropping and dropping and it didn't matter if I plugged it in it just would not charge so I didn't know whether it was a fault with the battery or the board so now the battery cells have to be okay because they're taken and holding the charge even now I will have charge in here let me just show you that now you can see that I've got 7.3 volts in there and and it will hold you know it will hold it won't drop but you see we've got a little sort of battery management board here so we've got five wires The Two Reds are connected together on the same solar joint the two blacks is connected together so really we've only got three wires positive negative in this yellow wire that's like a temperature wire you will see that from this point here it goes through the board to here little fire to here and it says NTC now if you watch my airfryer video you know an NTC will change resistance with heat so what I did is I went across here with my meter and I got an ohm reading off like a 11 000 ohms I think it was so actually I went from the black wire to the yellow wire here it was 11 000 ohms when I heated it up very very gently with my hot air thing here just just very quickly obviously not applying heat to the lithium cells then the resistance changed quite dramatically so I know the little NTC thing's working so that said to me it's probably not the battery it's probably something on the board if you have a look at the middle wire here it goes down a little via this tiny little wire here into this chip so I presume this is like the charging chip so I thought to myself okay what about if I short out with tweezers the negative against here so in other words then the ohm reading is going to be you know just a a complete short and it didn't make any difference beg your pardon sorry these are the negatives here like that it didn't make any difference and then I went from the positive to here and as soon as I did that came alive which I thought was weird and now it's charging at a good rate so I don't know by doing that have i kick-started something because I've kind of gone via the virus here underneath here and they travel up through here into this area uh or have I blown something in the chip I mean there was no smoke there was no nasty smells or any uh bangs or anything like that just nothing I just did that and all of a sudden on my meter it just started to charge up I think it was like 0.6 of an amp or something like that and that's when I started filming so I could show you so I'm going to put it back together now and show you what I mean so yesterday didn't matter what I did I could not get this to charge it was always 0.0 if I plug this in now with nothing in it didn't make a difference if the battery was connected or not it always gave me the same reading yeah and that's not going to charge at that low reading there so when I plugged the battery in yesterday that's all it was doing just that right now watch gotta be careful with this battery now right let me just balance it here plug it in look what it's doing now see now we've got two red lights I don't know if you can see that two red lights there and look at that we've got a nice healthy charge going on now that to me looks like that well I know at that level there the battery is charging because yesterday when it was 0.04 I had it plugged in for two hours and it wouldn't charge have I somehow kick-started that chip did that chip get kind of locked latched into some position and by me going across the positive not the negative it was the positive I went across and that temperature wire that's when it came to life now I must stress I did this whilst it was charging so I had the micro USB plugged in charging and that's when I went across the red wire and the yellow wire so I really don't know let's just see what happens so I'm just gonna tape this battery up now get it all back together and then I want to show you a picture printed out because I think it looks pretty impressive right I've found one here that was me when I went on my skateboarding weekend even though I haven't stood in a skateboard in years and years and years attempting to a wall ride I didn't land that but at that moment in time it was looking promising so check this out I hit this here oh also look sorry you can do tiles which is clever so each one of these pictures are three inch by two inch but look you can build up bigger pictures by doing it in tiles can you see so you can have nine there to make big pictures all right let's just do that one there connecting to sprocket printer it's lovely the way it comes out oh here it comes and these are sticky as well so you can basically peel them there oh look at that looks so old my friend was taking it using an actual black and white camera you know a film not digital look at that how good does that look it's a novelty little device right okay so uh yeah that is it I'm gonna leave this plugged in and I want to see maybe I'm going to turn it off I want to see maybe if after half an hour or so if it goes green well this is good news it's been about 45 minutes to one hour still amber light here it's at 86 percent but look can you see now the currents dropped right down so it looks like it's more going to trickle charging now for the last bit which is fantastic right brilliant news has gone to 99 here and it's not drawn anything look at that zero amps fantastic oh and it's gone to Green news so it looks like it's working what's a result that's fantastic right okay uh let's move on to another item now obviously I'll only know over time whether this is fully fixed but it's certainly doing a lot more than it did yesterday and it's showing all the signs that it's working safely because it's no longer charging when it gets to 99 which is just great excellent on to the next item right next up we have this thing here which is basically like a handheld gimbal thing and it is doing certain things but it has a bit of a mind of its own it seems to uh not stay focused on where it needs to stay focused to be fair it's doing pretty good now there you go it's gone off again but anyway you can see here that there's a joystick bit missing and the remains of it are in here but even if I put this in here can you see it just keeps moving because I presume it's uh I don't know what's going on there I think we need to take it apart and see what's going on with this joystick because right now I can't seem to get it to do what it needs to do and now gone again so I think what's happening is is it this is like in some weird position in here that keeps throwing it off so let's take it apart and see if we can work out what's going on luckily with this one there's just some Torx screws to undo and then we have a little sticker cover around one of the mounts we peel that off there's more screws under that the main handle that we actually need to get into is all just clipped together and it actually comes apart okay this one so basically the joystick is snapped as we look at the joystick closer we just have to undo the board some little screws the joystick is in on the other side what it actually is is a potentiometer if you imagine like an Xbox controller or a PlayStation controller the thumb sticks on that very similar to that but unfortunately different I can't just use that so uh the potentiometer is broken the axle or your the thumbstick attaches to is completely snapped off so it doesn't matter what you do with a joystick it's not actually moving the X and Y axis at all obviously it needs a replacement potentiometer but unfortunately I can't find one as I show you in this next part of the video and then I'll also show you a close-up of the potentiometer well I've looked on my phone for gimbal potentiometer and there's nothing that resembles this one here what I'll do is I'll zoom in because obviously it's just going to be an off-the-shelf part and maybe some of you will actually recognize the symbol and then you might be able to find out which one it is or tell me the manufacturer and then I'll be able to find one because I'm sure they're only going to cost a few pounds you see this symbol up here it kind of looks like an s it's a good workout what that is then we'd have a better chance of finding out so what I've done is I've dismantled this and you can see now this is how it works so we have that on the board we've got a carbon track up here and a carbon track here and we've got fingers that rub along it here and here one for this one one for this one and basically we need something to go in between the bottom here and this one here to be able to move around and then this to go on top so what I'm thinking is I've got a tiny little cable clip with a little nail if I was to grind it down and make this as flat as could be but still with a head on it then you see I'll be able to slide one end one hopefully all the way down there the other one all the way down here and then it still might be enough to where you know I might be able to whack it on there obviously when it's cut down to size so right now I need to do quite a bit of grinding I haven't got anything smaller than this at the moment but if I grind it down here and here with the Dremel tool then I'll put a grinding disc on then I might be able to get this to work and there should be quite a bit of strength in that more strength than plastic Theory me it really is like living in the days before the internet I just can't seem to get any of these things working because of lack of spares like you know nothing's coming up on Google and eBay and that's not the norm normally you will find something often it will be from AliExpress and you might have to wait a month or two for it to arrive but normally you can find some kind of record off it so I I feel like I've been a little bit unlucky so far anyway here I am just grinding this nail down trying to get this together I don't really know why I'm wasting my time on this to be honest with you it's just that I'm sort of thinking it'd be nice to see if it could move because when you move the joystick it's supposed to pan the phone left and right and up and down so it would be quite nice to see it work even if it's not going to work well anyway look let's get a move on with it and we'll give a shout out to the my mate Vince massive at the same time as you're watching this so the members this month are kidsdigital.com Kip hakes and Max rocketansky having fun repairs will Michaelis Chris seal Felipe mrkeeps.com djvg pigsy Robert from timsey's auto air Daniel Watson Zeke Anthony Dean Baza II operational 117 Russ and melonson Edis garbert and Gaspar Heller big big big thank you to each of you right so now I've got this bodge offer potentiometer back together let's see if it is actually going to work or not let's see now if it's going to do anything oh my word that's left and right doesn't want to Center very well though it does go left and right I just can't stop it I can't find the middle right okay does it go up oh yes it does look look that's pretty clever does it go the other way yes it does look excellent I just can't use it with my thumb because it's pivoting rather than you know moving like that but look we've proved it we've definitely proved this to potentiometer that's wrong now I should be ending this video here because it's already long enough and this length video will do better than a 50 minute video but I've had two fixes and two failures and I need is a need that fixes to win so I'm going to look through the box to find something that hopefully will be an easier fix that would just push the win to the fixes come on now Vince I need this right here we have Amplified hearing assistant so if you're hard of hearing you can put some headphones in and this is supposed to amplify the sound for the room into you and it looks brand new but look check this out turns on when I go to put my headphone jack in it just feels loose so it's got a little lithium battery inside but here there's nothing happening so fingers crossed this might be just a solder job I'd love to end on a positive I really like these surprise boxes because again something like this I would have never normally looked at right okay now what are we looking at something up here oh look at the microphone oh cool that's nice that it's got a proper little uh you know a bit of foam around it as well proper microphone here we go excellent there we go look at that completely off taking the pads with it though right let's zoom in and see if we can work out what's going on so we've got one feeding it here so that's no problem I can just scrape that back and we'll be able to sold it back onto that one fine this one here right that will take okay so that's fine I can take that straight from that little point there so this should be nice and easy have we got little holes no see look if we had little prongs here then it might have given a little bit more we have got one oh yeah they've broken off because they would have given it strength you see they would have given it a bit of insertion strength all right well what I'm gonna have to do is I think I'm gonna have to I haven't got any epoxy here it's in the Rolls-Royce otherwise I'll epoxy in should I just use a bit of super glue and then a bit of hot glue I think that's what I'll do I'm going to put it all around here and then I can maybe put some hot glue on the end bit all right so I'm going to let that set right so that's been drying for 10 minutes now with me holding it like this so hopefully it's going to be all right now I don't have much faith that the that is going to be that strong because you see those little bits have gone through here I was thinking about shoving something in but I can't there really is not enough height there it's just going to interfere with the Jack going into it so rather than just using using solder I am going to use a little bit of wire on each one and that means then that even if it was to push back a tiny bit there's a chance the wire may stay intact and also the wire might just give it a little just a tiny little bit of strength so this is just some solid core telephone wire for my sold it does have flux built in but I'm just going to add a little bit of flux and clean it up with some isopropyl alcohol at the end [Music] [Music] [Music] okay so that's it there now lots are sold on it and also a wire as well so I'm going to put it back in its home and then add the hot glue to it if it needs to come apart in the future a little bit of isopropyl alcohol removes the hot glue no problem at all foreign plugs in now we're on that one there let's turn it on oh I can already hear wow hello my God Hello Hello Hello Hello whoa that is seriously loud right let me put these up to the mic and speak into here and hopefully you'll be able to hear them even from here I can hear it really easily wow I wasn't expecting it to be quite so loud testing testing testing yeah so if you were hard of hearing then uh whoa that is so so so loud it really is yeah amazing right okay let's uh let's recap well that concludes this video so I only tested these items so I might have lots more videos in that box there you didn't see this one here this is the key Light mini it gives off a serious amount of light it's made by Elgato so they're the ones that do their video capture so for example you know when you're streaming and stuff like that so that would actually be useful for me because maybe I could get some good light on close-ups and stuff like that it's uh an expensive bit of kit that one there I think is 80 or 90 pounds as far as I can see it's fully working from what I've tested maybe the battery doesn't last long this one here is fully working looks to be around about 40 pound ish this one here is fully working believe it or not that is about another 80 pound the sprocket now appears to be working again 80 or 90 pounds and these two things here were failures but not through one-off trying it was just that I need a chip for that if I can get a chip for that I know 100 that will be working and if I can get a potentiometer for that one I know that that will 100 be working so if you were a reseller you've really made your money back on these items out of everything here I like this for the novelty point of view this one here I probably will use but the other stuff I wouldn't have been in the market for but it still makes for interest viewing and that's why I like these Amazon mystery boxes because I don't know what's going to turn up and I find out about things like this and this and this that I've never seen before so yeah massive thanks to the seller for sending these out hopefully there'll be another interesting video coming out of this box who knows after the comment section I might be able to get this one and this one fully working and then I conclude that it may be part two of this Amazon Mystery Box take care everyone [Music] foreign [Music] thank you and all of these [Music]

Channel: My Mate VINCE

Views: 265,255

Keywords: another Amazon Returns Box, fixing amazon returns, repairing Amazon returns, Amazon Return Box repair, another amazon returns mystery box, fixing electronics, fixing and flipping, repairing broken items, learning to fix electronics, fixing returned items, right to repair, my mate vince returns box, my mate vince amazon, fixing ebay items, repairing eBay products, fixing eBay items for profit

Id: hd3KKyKkLHY

Length: 43min 52sec (2632 seconds)

Published: Fri Apr 28 2023