Amazing Table Top Finish! - Epoxy and Wipe On Poly = Hand Rub Oil Finish

Video Statistics and Information

Video
Captions Word Cloud
Reddit Comments
Captions
all right right on folks john crane here in the shop and today i'm working on these redwood tables and specifically i want to show you how i apply the epoxy on these tables now if you want to go back and see how i flatten these you can go back and watch my last two videos where i show how to build a router sled and router table i'll put a link to those videos in the description while you're there drop a comment like subscribe you know the whole nine yards all right now there are many different ways of applying an epoxy finish and i use a variety of ways depending on how i want the finished product to turn out now in this case on these redwood tables i am not going for that eighth inch sheet of glass look now that has its time and it has its place it's good on a bar top or check out this ping pong table i did a few years ago now in this case i did a big tour it was a self leveling pour and i got about an eighth inch build of epoxy and that is great for that application but for these redwood tables i am a big fan of that hand rubbed oil finish look on wood i really like that i'm not a huge fan of the thick layer of epoxy so if you look at this right now it looks like a sheet of glass but i am in the process of putting several thin coats of epoxy on this table with a roller i sand in between coats and then ultimately i will put a top coat of wipe on poly on the top of this so essentially i'm using the epoxy to soak into the pores of this redwood now this is end grain and this is really soaking up a lot of epoxy and what's kind of how i like to use epoxy is put as much on as the wood will absorb and then sand it smooth and then put a coat of wipe on poly on the top and that turns into a real durable finish with that wipe on poly you can put a coat of that on any time you want to refresh the look of that table today i am using total boat table top epoxy now i also like using west system epoxy but for the nature of this redwood it has a very open porous end grain and it's going to drink up a lot of epoxy and the total boat epoxy is a little bit thicker and it's not going to suck up as much it also is less expensive than the west system epoxy all right here are a few tips to consider in detail now you want to have your room temperature between 70 and 80 degrees if you don't have the room temperature high enough your epoxy might not set up and the last thing you want to be doing is scraping that epoxy off of your project all right and now if you want your epoxy to run a little bit smoother there are some techniques to do that one is to put the epoxy into a water bath and heat that epoxy up i like to just set it on a bench next to my wood stove i let that heat up for a couple hours and that gets the epoxy nice and thin and easy to spread with a roller one thing to note when heating up your epoxy is that is going to kick off a little bit faster so you're going to have to work a little bit quicker all right you're also going to want to get some good mixing containers with some gradation marks on the side now this total boat tabletop epoxy is a one-to-one mix ratio you're going to want to hit that right on the head get that exact and mix it very thoroughly once you think you're done mixing mix it a little bit more scrape the sides get it thoroughly mixed all right now when it's go time you want to make sure you have some things ready ahead of time such as gloves brushes rollers you want a map gas torch you want some acetone for cleanup i tell you there's nothing worse than having your epoxy mixed up and ready to rock and roll and you can't find your roller now speaking of rollers i like to use these fiberglass resin roller covers made by red tree now these go for about 14 bucks a pop so i like to cut these into thirds with the multi tool and then i put these onto a smaller roller handle before i do that i like to take a lighter and torch any frayed ends so i don't get any residue into the epoxy [Music] [Applause] [Music] all right here we go the first coat of epoxy that i'm putting on is the seal coat on the bottom of these rounds and i tell you these rounds are just drinking up this epoxy like gatorade on a football field you can see here i am just spreading the epoxy around with an eight inch piece of plywood i'm not really concerned with spreading this around with a roller right now as this wood is just drinking it up so let this cure overnight all right here now it's the next day that bottom has cured i'm flipping this round over doing the old he-man actually this wood isn't very heavy it is quite dry it's been drying for several years so now i'm going to prep the top surface i'm just blowing off any residual dust and we will do the same process on the top of the round [Music] all right now this redwood bark is extremely thirsty as well so i'm going to put a coat over the whole perimeter of the bark [Music] all right good morning folks it's the next day and the seal coat that we put on top of our round is nice and dry so now we have a seal coat on the top of the round on the bottom on the edge of the bark everything is nice and sealed that's going to prevent air bubbles from coming through so the next step is to sand this i'm going to sand the top i'm also going to hand sand the bark so there's no little prickly thing sticking out i want this to feel really nice to the touch all right so i'm going to get busy i'm going to sand this then i'm going to mix up some epoxy and i'm going to roll that out here on the top all right let's rock and roll [Music] top of the morning to your royal [Music] [Music] do [Music] all right here i'm using some ca glue this is some 2p10 thick super glue and i'm filling in some of these deeper open cracks just getting a jump start on these it's nice to do this now you can fill these with epoxy and if you do fill these all the way up with epoxy sometimes they go all the way through to the bottom you can seal the bottom with this this is this hvac aluminum tape and that is great for sealing up those cracks it really sticks good to the wood you can also use tyback tape but i always seem to be using this and it works out just fine all right it's time to roll on our first coat with the roller this is going to be a nice thin coat i mixed up 16 ounces of epoxy eight ounces per table i'm gonna roll this out with this small roller and as you see here as i'm rolling it out it gives it a little bit of a stippled look don't worry about that i'm gonna come back with the map gas torch heat the epoxy and help that to level out [Music] aside from leveling the epoxy the map gas torch also helps to pop any air bubbles that are in the epoxy sometimes they come from the roller and sometimes they rise right out of the grain of the wood all right our second coat here has dried nicely and you can see it is still absorbing that epoxy in some places so we're going to put another coat right on top of this one [Music] [Music] all right here's what it looks like after sanding now this is sanding after our second roll on coat and it's looking pretty good there's a couple little voids here and there that need filling in and some places where there were some air bubbles i'm going to touch up some of these bigger ones just dab some epoxy on there and hit it with a torch if you're lucky sometimes you can reuse these mixing cups by peeling out the leftover epoxy in these after it's dry so you can pull that right out and then you get a nice [Music] all right look at this folks this is looking nice and smooth now the end grain is pretty well filled in with epoxy and i got gotta say this end grain is quite a different animal than just a regular flat slab of wood it really sucks up a lot of epoxy and it takes a lot to fill in all this end grain and get all the air bubbles out and all the little cracks but right now this is looking great on a regular slab of wood it might not take this many coats to get to this state so you just gotta observe your wood and see how many coats it's gonna take to get it done so right now i'm ready to put another thin coat on top of here i have the epoxy over by the wood stove heating up it's nice and warm right now so that's gonna enable it to be nice and runny so i'm gonna roll on another coat i'll sand that and then we'll do our top coat of wipe on polly [Music] so [Music] all right just a quick tip on some sanding pads a hand sanding pad i've had a couple of these for years they are great i just ordered in a new set by dura gold and i use six inch hook and loop for my sander and this is great because you can just use your six inch hook and loop right on these pads just set these down and you have a nice sanding block right there it's got some form fitted things for your fingers i'll put the link to this in the description definitely get a set of these if you got the hook and loop for your regular sander all right so now i'm going to take this i'm going to go around the perimeter of the bark and just make sure i got this all smooth around the edges all right now i'm getting ready for the wipe on poly so i'm going to go over the whole surface with the air gun and then i'm going to wipe down the top with a tack cloth [Music] all right now the time has come to put a coat on of wipe on poly i am using the minwax wipe on poly now wipe on poly is just essentially polyurethane cut with some mineral spirits that's all it is and i am using the clear satin this has some ground up silica in it it takes a little bit of that sheen away gives it a nice satin look i really like that now because it has that ground up silica in it you want to give it a really good shake here and so what i'm going to do is i'm going to take this cup i'm going to pour a little bit in here and then with the brush i'll go around the perimeter do the bark and then i'll wipe some over the top [Music] all right this is always a fun time in the process putting these final coats on and you really see the grain come out it's a really nice reveal of the grain so always exciting to pour on a little wipe on poly i'm just putting this on with a all cloth look at that redwood coming out it's beautiful beautiful such a nice looking slab of tree here huh gorgeous so i'll probably end up putting a a couple coats on i'll put this coat on right now i got the wood stove going and i'll come back here in a few hours all right look how nice that looks i was saying i'll come back in a few hours after this has dried and i'll put another coat on just gorgeous look at that what an amazing looking table huh [Music] all right i ended up putting two coats of the satin wipe on poly and this third coat i'm rubbing on is the clear gloss wipe on poly and this will give it a nice semi satin look you know i changed things along the way now i wanted to bring out a little bit more shine you know it's your painting you want to put a nice little happy tree right in the center you go right ahead [Music] [Music] [Music] all right right on folks look at that table it looks just amazing if you can see it in person it is just so beautiful i hope these pictures do it justice and i hope you can see in these pictures that it doesn't look like an eighth inch sheet of glass like some of those thick epoxy pores i really don't care for that look i really like this hand rubbed oil finish look and that we achieved that here it just looks dynamite all right i hope you enjoyed this video please like subscribe tell your buddies tell your friends all right hope you're doing great and i'll see you soon all right right on [Music] do [Music] you
Info
Channel: Right On With Jon Crane
Views: 40,468
Rating: undefined out of 5
Keywords: saw mill, right on with jon crane, john crane, live edge table, live edge epoxy table, live edge furniture, totalboat epoxy, west system epoxy, slab table, redwood table, epoxy table, river table, fixing cracked table, crack in wood, japanese saw, table glue up, woodworking, carpenter, woodwrights shop, this old house, totalboat table top epoxy, table top epoxy, wipe on poly, wood finish, wood finishing, epoxy resin, wipe on polyurethane, wood working
Id: P-AbEy1ND_Y
Channel Id: undefined
Length: 18min 5sec (1085 seconds)
Published: Sun Apr 03 2022
Related Videos
Note
Please note that this website is currently a work in progress! Lots of interesting data and statistics to come.