453. Throwing a 7-Lb Large Platter with Hsin-Chuen Lin 林新春 7磅大盤拉坯示範

Video Statistics and Information

Video
Captions Word Cloud
Reddit Comments
Captions
so this time I'm using a larger bat and again I'm kind of pushed down so the the pace is going to be a wider [Music] this piece of is a power around seven pounds so after I initial push out my pay slider I'm going to start to drill the hole [Music] so take it to the right thickness first I'm checking it so that's about a little bit more than maybe three eighth of inch and after that I'm going to just push the clay from the bottle try to squeeze it out so my fingertip is going in the corner and since I am making a platter so I don't need the the clay too high so after I push the corner I'm going to push down the clay right one more time pushing the corner using the fingertip here this is my fingertip the push and then my right arm is holding there to help in the meantime kind of smooth it see that there is a clear about some you know bum in here so I'm going to spread it out make sure it is slippery and then still quite a bit of a clay here so I'm gonna push one more time you so now as my index finger my right index finger is squeezing the clay from the bottom this ham is pinching so the left-hand side of a slightly pinch the clay and move up here index finger is squeezing it down so that I don't have too much play in the corner on the left hand is lifting right so there now I'm gonna bring my wooden rib the compressing rip to my wrong rep to compress this is the scientist and then since I have lots of wooden texture from the wooden ribs so I'm gonna remove it using a metal rib to that first time I will take care of the ascender by just moving my rib real quick well that take care of the very center and they're not away from the very center I hope my rib move out the horizontal way and slowly and when moved to here first I hold my rib more horizontal and then I compress it and smooth it and once my rig move to the very corner there's a curve here so I am my both hands and in the rib so there's a forming a little curve there so it's fitting right on the curve here okay so that's the large platter the key is that you need to have a real white base so that the outer prop is in the slump because you have a more support if you don't have support your foot is too narrow unless your clay is very firm otherwise it's easy to us come down so usually I when I'm making a ladder logic platter I use it a little bit softer so it's easy for me to move around but not to sell because you still need to have so I'm gonna support on the side so it'll be softer but not too soft and then spread out so you have a wider based supported okay so before you lift up from the wheel you might want to run the wire to cut it separate otherwise wasn't your pirate pride is gonna be a two hour are to cut it to cut it off from the bottom all you need to do is get a wire and then I slowly spin the wheel that we go to the chart okay you want to have a longer this one it'll be the bit too short a longer string and then one of your thumb is holding against the the wheel where the wheel spinning clockwise and then we're doing the job you don't need to use the whole strands to cut just spin your wheel slowly be able to cut it easily [Applause] right this is the demonstration on seven pound of clay the witness of power I would say about 15 15 inches wide the wheel has 14 so they'll have been hanging over you
Info
Channel: Hsinchuen Lin
Views: 4,297
Rating: 5 out of 5
Keywords: ceramics, pottery, wheel throwing, stoneware, porcelain, mypots, mypots.net, casserole, lidded jar, Vase, glazing, Hsinchuen Lin, 林新春, 手拉坏, 陶藝, Teapot, Teabowl, Chawan
Id: Ft2Ppj7ajrs
Channel Id: undefined
Length: 12min 29sec (749 seconds)
Published: Wed Jun 03 2020
Related Videos
Note
Please note that this website is currently a work in progress! Lots of interesting data and statistics to come.