10.6.10 Packet Tracer - Back Up Configuration Files

Video Statistics and Information

Video
Captions Word Cloud
Reddit Comments
Captions
markup configuration files in this activity you will restore a configuration from a backup and then perform a new backup due to an equipment failure a new router has been put in place fortunately backup configuration files have been saved to a triple file transfer protocol server the ftp server establish connectivity to the dftp server because this is a new router the initial configuration will be performed using a console connection to the router click pci the desktop tab okay pca click desktop tab terminal access rta command line terminal okay using this console cable you will access console on rta router okay and press return enter configure and activate gigabit 0 interface the ap address should match the default gateway for the tftp server okay review the tftp server desktop ip configuration or command prompt and ipconfig and should match the default gateway of this server 132 1611 and use the same subnet mask this is very very important subnet mask 24 you go to pca and router remember gigabit 0 enable configure terminal interface with zero zero ip address 172 16 1 1 subnet mask 24 enter and enable this interface now shut down enter now you can see the green indicator on the server side test connectivity to tftp server okay tftp server ip address is 172.16.1.2 go to pca and you are on router and to privilege exact mode and ping the server ping 172.16.12 success transfer the configuration file from the dftp server from privilege exact mode okay this privilege xml copy tftp to running config okay copy from tftp server is the source and running config will be the destination the router okay copy tftp to running dash copy enter and the address of the server 136 1612 192.16.12 and the source file rta.com rta dash conf g okay case sensitive enter the destination file by the file running config okay use the default enter the router should return the following okay very good copy it okay 785 bytes very good issue the command to display the current configuration so running dash config enter and now you can see the host name the interface you can beat zero zero you can be zero one it is shut down you can be two when we shut down you could be 0 passwords on bty lines password on console banner okay what changes were made okay previously the router hostname is by default router and when you copy the configuration file from tftp server to running config now the hostname is rta the host name is rta and in configurations like enable secret might be the main lookup interfaces configurations banner line console and bty lines issue the appropriate show command to display the interface status okay so ip intel interface brief are all interfaces active okay um you can be zero zero status up protocol protocol app gigabit zero one status administratively down protocol now okay the answer is gigabit 01 is shut down corrupt any issue is related to interface problems and thus connectivity between pca and the tftp server okay first enable gigabit zero one for your terminal interface gigabit zero one enter no shut down now you can see the green indicator here and there's connectivity between pca and dftp server okay this is pca close the terminal go to command prompt and ping the tftp server 172.16.12 success backup configuration and ios to dftp server change the hostname of rta to rta-1 okay you are on pca close this open terminal okay and continue configuring rta exit and on global configuration mode change the hostname hostname rta dash one right enter now the hostname is rta-1 save the configuration to mbram okay add to from privilege excel mode copy from running config to start copy enter enter okay running config is the configuration on ram and startup config is the mbram now copy the configuration to tftp server using the copy command the copy from running configuration on ram is the source the destination is tftp server okay copy running config to the ftp column okay and the address of the remote host the server 132 16 1 2 and destination file rta 1 okay use the default press enter use that file name enter ok 151 bytes copied very good issue the command to display the files in flash so flash column enter okay here this is the ios image the image of this router rta backup the ios in flash to the tftp server using the following commands copy from flash on this router is the source destination the tftp server copy from flash column source the destination tftp server column enter source file name is this just this okay c 1900 universal k9 mz dot spa okay sensitive 15 1 [Music] okay this name and press enter address or name of remote host the server ip address 172 1612 destination file name use the same name as the destination enter okay about 33 megabytes copied what special character repeatedly displays indicating that the ios file is being copied to the tftp server successfully okay this character okay the exclamation point open tftp server and click the services tab select tftp and scroll through the list of ios files go to tftp server close command prompt open service stop tftp and now you can see the rta one config this file and also the [Music] the image of the router and the image was c 1900 universal volcanic amc spa 15 1 4 and 4 beam and is this cn1903 universal gain imc spa 15 1-4 and 4-beam very good has the ios 5 cnic-00 universal k9 mz spa 15 1 4 and 4 being copied to the tftp server yes okay and it's listed in the dftp server completion 100 thank you very much you
Info
Channel: Christian Augusto Romero Goyzueta
Views: 2,921
Rating: undefined out of 5
Keywords: ensa, enterprise networking, security, automation, ccna, version 7, ccna 7, ios, image, upgrade, configuration file, config file, config, TFTP, running-config, nvram, startup-config, flash
Id: -sd14XfqMNA
Channel Id: undefined
Length: 13min 1sec (781 seconds)
Published: Sun Sep 13 2020
Related Videos
Note
Please note that this website is currently a work in progress! Lots of interesting data and statistics to come.