Hello friends, today we are going to introduce the water head of the basin and the actual replacement operation. Today we are going to take a look at the hot water head of this basin and washstand . Then we will actually operate it here. First of all Let's introduce the material of this drain head. As for the material, you can obviously see that this one is made of plastic, then this one is made of copper , and this one is made of stainless steel. As for the price, this one is made of copper plus electroplating. Well, as for the price, this one is probably around 250-300, this one is around 200, uh, this kind of one , I don’t know the price. This kind of social one should be cheaper , maybe 100 yuan. I said cheap , uh, the utility store may not sell it. What I’m talking about for such a cheap price may be that for example, you can buy it at a cheaper price on the Internet , because the price difference is not said to be very large. If it were my personal choice, I would choose stainless steel. Then
let’s take a look at this style. Okay, this one looks quite different from these two. This one, we call it the pull-rod type water head . There is a pull rod here, and there is a pull rod here . And this pull rod is installed during installation. When there is a hole on the side of the water head, you have to go through this hole and then rely on this lever . This is connected to the back of the Longlong faucet. Then relying on the lever, he can control this and control this to turn on the light. Close . This one is a bouncing type or we say push type . It bounces like this. Bouncing type. This one is also a bouncing type. I personally think I prefer this type of bouncing type. Why? Because the most important thing is that there will be some dirt, hair, and dirt accumulated on the water head . These two bounce types are easier to clean. Which one? Because the hole in the water head will be penetrated by the iron. So there is no way to take out this head that has fallen into the water . Unless you take this mechanism, open it here and pull out the iron, then you can pick it up. So this kind of thing is relatively difficult to clean , so I can't. It is recommended to use this type for the sake of cleaning. What about this kind of pop-up water head? It is relatively easy to clean like the stainless steel one. It can even get up by pumping it like this. This one does not need to be locked. It can be cleaned very conveniently. The pop-up type like this one cannot be pulled out. It has to be rotated. It has teeth, so if you buy it then, you can choose something like this one in the middle. There is a circle of teeth here on my thumb , so it won’t be easy to pull it out when he puts it on his hand. This kind can be taken out directly. This is the white circle on my thumb. He has no teeth. So he can directly extract it like this. What if your bounce switch is broken? Sometimes it stops bouncing after being used for a long time , or the bounce switch is broken. This bounces the heart. Haha, this can be bought separately. You don’t need to buy this whole set. You don’t need to buy this whole stick. You only need to buy this core . Then when you choose, you have to choose this kind of toothless one or this kind of toothless one. After introducing the material and style of the teeth , let’s take a look at the design. Basically, it’s the core, right? Let’s start with this part here. The drain head is installed at the washbasin. The structure here is the same. This is metal. We will touch the part of the washbasin . There is a rubber washer on the top here . There is also a washer on the bottom here. The washbasin is in the middle, right between the two pieces of rubber, below this piece of rubber. There will be a plastic gasket. Let you see it clearly. The plastic gasket looks like this. This plastic gasket is used to make you press the ring. 6 This is a hexagonal hexagonal copper ring . Well, what happens when it presses? This rubber will not be torn because when it rotates, it will press on the plastic piece. If it is designed like this , please remember that any place where hard metal like this contacts hard ceramic must have this rubber pad . When installing this drain head, we will wrap a thin layer of anti-leak tape under the first rubber gasket. The purpose of this anti-leak tape is to make the teeth This rubber gasket can better seal the water material and prevent it from leaking out from the teeth and this part of the rubber gasket. Then we can even add a little anti-leakage tape on the rubber gasket, everyone
. Pay attention to the rubber gasket. If you remove it like this , this rubber gasket is flat on this side. The flat side is at the bottom , and then this one is slightly curved and convex. This is where it touches the washbasin . On the side, this anti-leak tape is wrapped. It should be thin. It doesn't need to be too many, about 5-6 turns. That's it. Then there are two holes on this side. You can see this side, this side and this side. There are two holes on the side. This is the overflow hole. Wait a minute. If we need to fix it during installation, we can use the screwdriver to pass through the overflow hole from here to fix it. Otherwise, it will not work when we lock it during installation. It may be rotated well. Let's do the actual operation now. Let's disassemble the drain head. This is a tie-rod type. The tie-rod drain head . Then we will disassemble the P-pipe together with the P-pipe later. We won't replace the part , so we will only replace the part of the drain head. The so-called pull-rod drain head means if there is a rod here, I have already removed it because when I replaced the faucet, I already had a pipe running down the top of the faucet. You can control this control. You can control the opening and closing of the water head. This U-shaped one is a water storage bay. The water storage bay is where we drain water every time. If the water is drained, there will still be water in the u. Well, the main use of this is to prevent cockroaches and odor. Cockroaches can't crawl in because the U-shaped interior is full of water, so the odor won't rush upward. So it's designed like this. In the past, other people here, uh, I I haven't mentioned it before. If you open it here, you can remove water or some dirty things . Is there water inside ? If you have dirt, it will come out from here. The dirt will gather inside this U-shaped shape. If you need to dismantle this, it will be very simple. I will loosen two of them here . Ring and loosen it. Then it can be pulled out like this . If we want to dismantle this pull-rod-type drain head, we must first remove it here and take out the pull rod . Then we can take out the drain head on top. Only then can he pick up the plug for the sinking head. Let me show it to you . Is there any design for the sinking head? There is a hole here, this plug. I have already picked it up. There is a hole here, this one. This pole goes through this hole, and then up and down, you can control the upper and lower corners of the drain head. When installing, it is the same. You need to insert the drain head into the hole first , and then I have to align the iron rod below with this one. Hole, go through it. Next, we can rotate down the unique section of this lever-type water drop head. This is the hole that the lever just went through. After rotating down, there is a 6-corner 6 here. The corner ring is good. Then we need to use a wrench to turn it down. This is a forced ring. We turn it down. Remove the forced ring and it will look like this. 6 hexagonal hexagonal one. Then there will be a plastic gasket. That's because it may be relatively close to the rubber , so we can use this flat-blade screwdriver to fiddle with it a little so that there is a plastic gasket , and then there is the rubber , because my head that fell into the water is still fine, so I may want to I prefer to keep it , so I may have to be more careful when disassembling the eraser. I hope the eraser doesn't rot. It's already rotten. If you don't want this eraser , you can just pull it. After removing the rubber ring, if it looks like this, this one actually pushes up. Then the leaking head can be taken off. After removing it, is the leaking head on the top like this? You can pick it up. Then we will clean it up a little later. Clean it up at once . Clean the top and bottom . Then we want to replace the push-type drain head . So let's install this drain head now. First, start from the top. Remember to have a piece of this black rubber . Then let's put the hot water head through this hole first. As a reminder, the lower section can be rolled down. You can also add some anti-leak tape at the connection between the lower section and the upper section, just in case. If the length needs to be cut, you can remove the lower section . First, put the hot water head in place. After installing the water head from above, we need to put this piece of rubber pad first , and then the protruding part will be upward . I have already put some anti-leak tape on it , so we can slowly push it up like this. The main purpose of using the anti-leak tape on the rubber pad is to make the contact area between the rubber pad and the basin closer. Ah, because sometimes the washbasin may have burrs or uneven edges. If we look like this, it can be more dense. After the rubber pad is installed, we use this plastic pad at home. After the plastic pad, we need to use this 6-cornered one like this. As for the nut, he then forces the rubber pad to lock it until the hand cannot lock it, so we need to use a tool to turn it. When you lock the whole nut, the head will rotate when it falls into the water. Then we can use a screwdriver like this. Isn't there a water hole next to it ? Well, let's insert it into that hole because it's hard to fix it like this so that it doesn't rotate . Then we can use this screwdriver to help. Then we finally put this Don't turn it too tight. The head that falls into the water will not move or rotate. It will be stable. This is enough. If it is too tight, the basin may be damaged. Next, we will install the P pipe below this time. There is a piece of rubber on the side that is stuffed into the hole to prevent water from flowing back out. This is called the butt, this rubber pad. Then we first insert this rubber pad into the tube. If we want this rubber pad to have a better tightness, then we You can also wrap some anti-leak tape on the outside first. We will insert this section first. Sometimes this section will be long or short. You can cut it, including this one . If it is metal, you can cut it. You can use a pipe cutter to cut it . The main thing we need to do is put it in first and then put it in the bag. If we put it in, the pipe must be perpendicular to the wall. We cannot hang down or go up like this. This will cause special effects here. For example, if you go this way, often if this side is higher down here, it is very likely that the dirt will gather on this side of the pipe, so we should at least be level, level, that level, let's take a look at this Is there a big difference between the distance between this tube and this tube ? If it's a little longer like this, it's acceptable. It's still about a finger's distance away. Then it's acceptable. We won't cut him if he reaches into this. It 's about 5 centimeters long. Don't push it all at once. If you push it all the way, it may be that there will be poor drainage. I just forgot to remind you that the cover we are modifying needs to be put on first . Let's just measure the approximate distance. Okay, OK, no problem. Finally, let's put this on again. Turn around and put it on first, then tighten it. You need to pay a little attention . Don't insert the tube too deep at one time. Inserting too deep will affect the drainage . Once you are sure there is no problem, lock these two buttons. If there is a rubber in it, you will grab the tube after pressing it. This way it will not move or loosen. Then it is OK. Then we can try it. Now let's push the modification cover to the wall. Finally, test the water storage in the washbasin and then drain it. Then try to see if there is water leakage here or in this place or all. If the joints are not leaking , then it is done. Then today our video will be shared with you here. If you like my video, please give me a like and share my video.