For those who have a high-pressure cleaner at home and are experiencing abnormal noise during use, the water is lighter, the machine heats up quickly, the motor cuts off quickly, and people who want to maintain the sprayer. High pressure water can be used for a long time. Definitely don't miss this clip. Hello, welcome to Daddy's Tips channel. I believe that at this moment most people don't know that high-pressure cleaners need to change the oil as well. Here I have a sample picture of the inside of the pump that has never been Maintenance by changing the engine oil. And then you will see the deteriorated engine oil inside. Looks like there will be thick sediment. In which this engine oil will act as a lubricant and will help to cool the pump as well. which if it deteriorates, it will cause many symptoms The symptom that we regularly encounter is that when the machine is working, the sound will be unusually loud. Then the water that comes out will also be lighter. And if the symptoms are heavier, the machine will be so hot that it cuts often. Worst of all, the motor burned out. In this clip, I will have a high-pressure cleaner from Flow energy, model B2 and model M9, which has been used for a while. I'll take both of these models to show you how to change the engine oil. For the replacement process, you can use a general tool like an L-shaped hex wrench like this. I'll start with the B2 model first. Notice that this model has a mask on it. We have to use a hex wrench to tighten the screw. Come out first. There are four screws on the mask. The tightening is normal. Tighten counterclockwise. These four screws we will use as a hexagon number three. At the front frame, we can remove it for the B2 model after the mask has been removed. We can see the oil change hole here. But for the M9 model, we don't have to remove the mask at all. We can see the oil change hole right here. Both of these models will be the new models of this year 2023. They will have an oil change hole for us to change easily, which is different from the previous model that he didn't have a hole to change. Give me the engine oil. For the original model, we can still change the engine oil as well. But we have to remove the pump head. Which I will show you how to remove the head in this clip. In a moment, I will come to manage the B2 machine that can adjust the pressure first. This one is recommended for us to set it up first. For the oil change port, we will use hexagon number six. We have rotated out, this time we can lift it. You can see that the engine oil here is still clear. But notice that there will be black sediment waiting everywhere. This one is a non-pressurized version of the M9. The change is the same. The oil change port will be in this position. which is the same position and if asked when to change If it is used every day, it should be changed every month. or if it is counted as working hours, we will count at 50 working hours, we will change it once. For home users, if it's not really used, after one year, it should be replaced. You can see that the oil that comes out is close to each other. But here I have a sample oil that has been taken out of a machine that has been used regularly for six months. Compare them clearly. Deteriorated oil will become thick and have sediment like this. The oil that can still be used will be like this. When adding engine oil, we will use it in a volume of 60 cc, which we can use general car oil. Whereas the engine oil number, we can use the front as anything. but behind us Use number thirty W. for machines not over two years old If it happens that the high pressure washer we have been using for two years now. We will use number fifty W. Because the piston device has been used for a long time. It may be loose. Not fit like buying a new one Therefore, we add a slightly higher viscosity number of engine oil. It will have better performance. Before we add the oil we should measure out the oil to the volume of sixty cc. It will make us work as easily as possible. But if we don't have a measuring place, we shouldn't add oil to more than seventy percent of the engine compartment. Because in the machine room during the machine is working, it will cut the oil to lubricate different parts. And there must be space to cause gas inside as well. As for the nine m engine, we will also use 60 cc as well. This one, relying on the cone will make it easier for us to fill. How is it? It's not difficult to change the engine oil for high-pressure cleaners, right? The Flow Energy high-pressure cleaner model B2 that I currently use. This model will not have an oil change hole. which I think the high-pressure cleaners on the market will be like this Therefore, I will come and change this photo for you to see as well. The first step is the same for me. Then will use a hex wrench to remove the screw. I'm in the same position. And as before, we can remove the mask. Now we set it upright. You will notice that we are unable to place it upright. and then take one of the pliers and put it back like this Here it will be able to stand upright and Note that there are four screws here. and then use it as a hexagon number five in screwing it out You will notice that the screws are not the same. We also have to remember the location that Which screw is in which position? And inside it will have a spring. So when we remove the last screw We have to support the head with me because otherwise Be careful it pops out. This is a screw in short Let us be careful with the wires here too. It will be the wire that goes to the switch. And would like to notice that at the edge here, there will be one O-ring. If it comes off, let us put it back in before we put it back together. If it happens that we come to see the place in the oil room, I These will be a set. This one will be a ring. And this one will be a bullet. There will actually be another ring. But let's pour the oil out first. Let us prepare some tissues to absorb. If we meet like this, it is not possible anymore and should be changed urgently. Which removing the engine compartment like this will have advantages. That is, we can see if there is damage inside this piece or not. We were able to come and change it. if there is damage Then we wipe the engine oil that still remains a bit. in order to wipe the sediment stains out as well and notice that it will have a groove and put the bearing in the groove here and then try to check if it can rotate or not and then take another part of the bearing set Let's make the part smoother. and then put the groove on the bearing and see if it rotates or not If it can be rotated, it's fine. If it happens that it's opening the engine compartment like this When we fill the engine oil, let the level of engine oil flood the knots. That's enough. Because we need about thirty percent of the space left in the engine compartment as well. which the volume of about sixty cc. would be just right for me don't forget me It will have an O-ring here. If it comes off Put it in the groove like this too. Here it will have a piston spring. Therefore, when we put down We will press the piston spring a little. and then press down on the springs, we screw them in one by one A little bit of each Where we start to fix it from the bottom two first. It will be easier for me. When the bottom two can go in a little bit, then we can start to wind the top two. Then we screw it in until it's tight enough. And this is the old oil that was drained out. I can see that it has sediment and it's quite thick. Then it's the same, we take the mask and assemble it, friends will see that if there is an oil change compartment, it will be much easier. Although we use a model with oil changing channels. We use it for many years. We may take off the engine oil room to see once in order to see if there is a spareor that has to be changed or not. with me Which, if friends, friends can follow this, they will be able to use the high-pressure water sprayer for a long time. And both of these high-pressure cleaners I have reviewed. In the previous clip, including how to clean the air conditioner. Including how to clean the air conditioner as well. I will leave a link Put it in the description under the clip and will also pin it in the comments. which I would like to conclude that whatever tools we have already purchased In order to use the most worthwhile, it must be maintained on a regular basis. So that he can work at full efficiency and can be used for a long time as well. And if anyone likes the techniques shared in this clip, don't forget to like. and then share it for your friends to see too If you haven't subscribed to Daddy's TIps channel yet, don't forget to subscribe. There will always be a clip of good knowledge for you. As for this clip, I leave it for now. Hello.
